NF S61-966-1999 Fire protection equipment Self-contained smoke alarms 《防火设备 配套式烟雾报警器》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

FORD WSS-M4D962-A-2011 THERMOPLASTIC POLYESTER ELASTOMERIC MOLDING COMPOUND 20% GLASS FIBER REINFORCED TO BE USED WITH FORD WSS-M99P1111-A 《20%玻璃纤维增强热塑性聚酯弹性体模塑材料 与福特WSS-M99P1111.pdf

FORD WSS-M4D963-A1-2011 THERMOPLASTIC ELASTOMERIC MOLDING COMPOUND INTERIOR TO BE USED WITH FORD WSS-M99P1111-A 《内部热塑性弹性体模塑材料 与福特WSS-M99P1111-A 一起使用》.pdf

FORD WSS-M4D964-A3-2011 THERMOPLASTIC ELASTOMERIC MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《热塑性弹性体模塑材料 与福特WSS-M99P1111-A 一起使用》.pdf

FORD WSS-M4D966-A-2010 THERMOPLASTIC ELASTOMERIC MOLDING COMPOUND (TEEE + PBT) INTERIOR TO BE USED WITH FORD WSS-M99P1111-A 《汽车内部用热塑性弹性体成型料(TEEE)+聚对苯二甲酸丁二醇酯(PBT) 与标准FORD WSS-M99.pdf

FORD WSS-M4D967-A1-2010 POLYKETONE (PK) GENERAL PURPOSE INJECTION MOLDING GRADE TO BE USED WITH FORD WSS-M99P1111-A 《通用注塑级聚酮（PK） 与标准FORD WSS-M99P1111-A一起使用 》.pdf

FORD WSS-M4D967-A2-2010 POLYKETONE (PK) GENERAL PURPOSE INJECTION MOLDING GRADE 15% GLASS-FILLED TO BE USED WITH FORD WSS-M99P1111-A (Shown on FORD WSS-M4D967-A1)《15%玻璃填充的通用注塑级聚酮.pdf

FORD WSS-M4D967-A3-2010 POLYKETONE (PK) GENERAL PURPOSE INJECTION MOLDING GRADE 30% GLASS-FILLED TO BE USED WITH FORD WSS-M99P1111-A (Shown on FORD WSS-M4D967-A1)《30%玻璃填充的通用注塑级聚酮.pdf

FORD WSS-M4D968-A-2010 POLYAMIDE (PA) 6 HEAT STABILIZED 30% GLASS FIBER MINERAL REINFORCED MINIMUM 25% PCR AND OR PIR CONTENT TO BE USED WITH FORD WSS-M99P1111-A 《热稳定30%玻璃纤维 矿物加.pdf

FORD WSS-M4D968-B1-2013 POLYAMIDE (PA) 6 HEAT STABILIZED 30% GLASS FIBER MINERAL REINFORCED TO BE USED WITH FORD WSS-M99P1111-A .pdf