1、Best Practices Entry: Best Practice Info:a71 Committee Approval Date: 2000-03-09a71 Center Point of Contact: GRCa71 Submitted by: Wil HarkinsSubject: High Voltage Power Supply Design and Manufacturing Practices Practice: Practice: Thoroughly test high voltage power supply packaging on flight configu
2、red engineering models, in a simulated space flight environment, to evaluate corona effects.Programs that Certify Usage: This practice has been used on Space Electronic Rocket (SERT) Tests I and II, Communication Technology Satellite (CTS), 30 cm Thruster Bi-module.Center to Contact for Information:
3、 GRCImplementation Method: This Lessons Learned is based on Reliability Practice No. PD-ED-1202; from NASA Technical Memorandum 4322A, NASA Reliability Preferred Practices for Design and Test.Benefits:Process controls on design, manufacturing, and testing operations reduce component failure rates an
4、d improve reliability. The goal is production of power supplies that will operate in space for the mission duration.Implementation Method:Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-There are special requirements in packaging HV power supplies fo
5、r space use. The power processor should be voltage-partitioned and the low voltage circuits should be separated from the high voltage circuits. This is usually done with a metal wall. There still will be signals transmitted between the sections. All grounds should be isolated to provide a means to p
6、redict the currents when transients or arcs occur. When capacitors discharge, there can be current flows of several hundred amperes. The low voltage section should be protected from these current and voltage surges.Table 1 shows recommended design practices used for an 11 kV CTS TWT power supply. Al
7、l volumes must be vented. The pressure in any unvented volume will decrease gradually and result in corona or arcing. Allow for screens, RF traps, etc.; and count only the holes in the screens. Interior volumes, down to the capped nut plates, must also be vented.Table 1. High Voltage Power Supply De
8、sign Guidelines PHYSICAL LAYOUTVoltage Partitioning (Separate high and low voltage components)Isolated Grounds (Provide known current path for transients)Voltage Suppression (Suppress signal from high voltage to low voltage circuits)ELECTRIC FIELDSSolid Dielectric: DC Stress 50 Volts/MILAC Stress 10
9、 Volts/MILSurface Creepage 8 Volts/MILAir or Vacuum Gap 20 Volts/MILVENTING2 cm2per 1000cc of enclosed volume (screens and RF traps reduce vent size), including: Capped nut platesDielectric spacersPolyolefin shrinkable tubingHigh voltage connectorsFigure 1 shows the fabrication methods used to build
10、 this supply. Round off all edges on metal as well as dielectric materials. Use anti-corona spheres. Void-free encapsulation is important. Remove excess RTV from bolts to keep vent paths open. Use shrink tubing in strips for hold downs, to avoid Provided by IHSNot for ResaleNo reproduction or networ
11、king permitted without license from IHS-,-,-trapped air. Dielectric separators must be sized correctly for surface creepage. Anti-corona spheres should have a vent hole to eliminate voids in the solder. Dielectric inserts should be slotted to vent the interior volume.refer to D descriptionD Figure 2
12、 illustrates the special construction methods used in the HV compartment for the equipment to operate in the thermal and vacuum environment of space. Table 2 shows the testing methods that should be used to check out the HV power supply. The glass epoxy boards should be scanned ultrasonically to che
13、ck for density differences. The transformers and components mounted on the boards should be corona-tested. Corona discharges of less than 5 picocoulombs are allowed. Induced voltage in the dielectric testing should be done in vacuum at temperature per MIL-T-27. The corona tests should be repeated to
14、 detect internal degradation from the high voltage stress. Be careful to bake out the components at 65 degrees C for 72 hours in the vacuum chamber and cool the components down before the power supply is turned on.Provided by IHSNot for ResaleNo reproduction or networking permitted without license f
15、rom IHS-,-,-refer to D descriptionD Table 2. Testing Corona testing: Transformers Component Configuration on Boards 5 PicocoulombsProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Electric Testing: Induced voltage (twice-rated voltage) Dielectric withs
16、tanding (2.5 times rated AC and DC) Important to perform in vacuum at temperatureThermal Testing: Minimum of 10 temperature cycles at component level Minimum of 3 temperature cycles at box levelInitial thermal-vacuum test preceded by bakeout of 65C for 72 hoursUltrasonic Scanning of Glass Epoxy Boar
17、ds (NASA TM X-73432)Technical Rationale:These design criteria were developed experimentally. The various component configurations, board layouts, and component assemblies were tested to 125% of expected working voltage in air, vacuum, and full operating temperature with a requirement that the corona
18、 inception measured less than 5 picocoulombs.An example of an early flight failure caused by corona was a short that developed between two pins of a high voltage connector. Gas trapped inside connector voids gradually decreased in pressure until corona discharge began to decompose the insulating mat
19、erial. When the insulating material thickness was reduced to the point that leakage started increasing, a carbon tree formed and a short occurred, disabling the experiment. This can be easily avoided by running corona tests on all high voltage parts to ensure that no gases are trapped in high voltag
20、e circuits.References:1. MIL-T-27, “Transformers and Inductors (Audio, Power and High-Power Pulse), General Specification for,“ August 8, 1987.2. NASA CP 2159, “Spacecraft Transmitter Reliability,“ September 1979.3. NASA TMX-3287, Lalli, Vincent R., Nueller, Larry A., and Koutnik, Ernest A., “System
21、 Reliability Analysis Through Corona Testing,“ September 1975. Presented at Power Electronics Specialist Conference (sponsored by IEEE), Culver City, CA (June 9-11, 1975).4. NASA TMX-73432, Klima, S. J. and P. J. Riley, “Ultrasonic Evaluation of High Voltage Circuit Boards,“ June 1976.5. NAS3-17782,
22、 Cronin, D. L., “Modeling and Analysis of Power Circuits,“ TRW Systems Group, June 1975.6. NAVMAT P4855-1, “Navy Power Supply Reliability Design and Manufacturing Guidelines,“ December 1982.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-7. Foster, W
23、.M., “Thermal Test Report for the Space Acceleration Measurement System Circuit Boards“, NASA Lewis Code 6730 Internal Report, November 1987.Impact of Non-Practice: Impact of Nonpractice: Allowing High Voltage power supplies that have not been thoroughly tested for corona to operate in space has res
24、ulted in corona-caused shorts that disabled the power supply.Related Practices: N/AAdditional Info: Approval Info: a71 Approval Date: 2000-03-09a71 Approval Name: Eric Raynora71 Approval Organization: QSa71 Approval Phone Number: 202-358-4738Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
