1、 AEROSPACE STANDARD CONNECTOR, RECEPTACLE, ELECTRIC, BOX MOUNTING, SOLDER CONTACTS, AN TYPE ASCopyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photoco
2、pying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED2004-06REVISED2017-01THIRD ANG
3、LE PROJECTION CUSTODIAN: AE-8/AE-8C1 REV.C FEDERAL SUPPLY CLASS 5935 AS SHEET 1 OF 6 REV. C PROCUREMENT SPECIFICATION: AS50151 6$(7HFKQLFDO6WDQGDUGV%RDUG5XOHVSURYLGHWKDW7KLVUHSRUWLVSXEOLVKHGE6$(WRDGYDQFHWKHVWDWHRIWHFKQLFDODQGHQJLneering sciences. The useof this report is entirely voluntary, and its
4、applicability andsuitability for any particularuse, includingany patent infringement arisingtherefrom,LVWKHVROHUHVSRQVLELOLWRIWKHXVHUSAE reviews eachtechnical reportatleast every fiveyears at whichtime it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and sug
5、gestions. SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS31021C RATIONALE REVISION IS REQUIRED TO ADD AN APPLICATION NOTE TO CLARIFY THE ENVIRONMENTAL SEALING PROPERTIES OF THIS CONNECTOR. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING THE
6、 PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS50151. FIGURE 1 - CONNECTOR CONFIGURATION AND DIMENSIONS AEROSPACE STANDARD AS SHEET 2 OF 6 REV. C CONNECTOR, RECEPTACLE, ELECTRIC, BOX MOUNTING, SOLDER CONTACTS, AN TYPE TABLE 1 - FIGURE 1 DIMENSIONS SHELL SIZE A COU
7、PLING THREAD B MIN USABLE THREAD D +.015 (0.4)/ -.000 INSIDE DIA I MAX INSERT DIA JJ 1/ +.031 (0.8)/ -.000 INSERT LOCATION 8S 1/2 - 28 .375 (9.5) .370 (9.4) .250 (6.4) .562 (14.3) 10S 5/8 - 24 .448 (11.4) .320 (8.1) 10SL .448 (11.4) 12S 3/4 - 20 .557 (14.1) 12 .625 (15.9) .750 (19.1) 14S 7/8 - 20 .3
8、75 (9.5) .682 (17.3) .525 (13.3) .562 (14.3) 14 .625 (15.9) .750 (19.1) 16S 1 - 20 .375 (9.5) .807 (20.5) .650 (16.5) .562 (14.3) 16 .625 (15.9) .750 (19.1) 18 1-1/8 - 18 .932 (23.7) .770 (19.6) 20 1-1/4 - 18 1.058 (26.9) .925 (23.5) 22 1-3/8 - 18 1.182 (30.0) 1.020 (25.9) 24 1-1/2 - 18 1.307 (33.2)
9、 1.145 (29.1) 28 1-3/4 - 18 1.526 (38.8) 1.365 (34.7) 32 2 - 18 1.776 (45.1) 1.615 (41.0) 36 2-1/4 - 16 1.995 (50.7) 1.830 (46.5) 40 2-1/2 - 16 2.245 (57.0) 2.045 (51.9) 44 4/ 2-3/4 - 16 2.495 (63.4) 2.300 (58.4) 48 4/ 3 - 16 2.745 (69.7) 2.550 (64.8) SHELL SIZE K THICKNESS MOUNTING FLANGE L MAX OVE
10、RALL LENGTH MAX MIN MIN CLASS A & C CLASS K CLASS A & C CLASS K 8S .156 (4.0) .062 (1.6) .062 (1.6) 1.191 (30.3) 1.375 (34.9) 10S 1.438 (36.5) 10SL 12S 12 1.713 (43.5) 1.812 (46.0) 14S 1.191 (30.3) 1.438 (36.5) 14 1.713 (43.5) 1.938 (49.2) 16S 1.191 (30.3) 1.438 (36.5) 16 1.750 (44.5) 2.062 (52.4) 1
11、8 .203 (5.2) .094 (2.4) .078 (2.0) 1.938 (49.2) 20 2.250 (57.2) 22 24 28 32 .359 (9.1) .125 (3.2) 36 .125 (3.2) 40 44 4/ N/A 2.188 (55.6) N/A 48 4/ AEROSPACE STANDARD AS SHEET 3 OF 6 REV. C CONNECTOR, RECEPTACLE, ELECTRIC, BOX MOUNTING, SOLDER CONTACTS, AN TYPE TABLE 1 - FIGURE 1 DIMENSIONS (CONTINU
12、ED) SHELL SIZE M +.031 (0.8)/-.000 MTG. FLANGE LOCATION N 3/ +.000/-.188 (4.8) OUTSIDE DIA O REF MOUNTING HOLE P +.015 (0.4)/-.000 KEY HEIGHT R .005 (0.1) CC - CL MTG. HOLE 8S .562 (14.3) .532 (13.5) .562 (14.3) .130 (3.3) .594 (15.1) 10S .656 (16.7) .688 (17.5) .165 (4.2) .719 (18.3) 10SL .782 (19.
13、9) .812 (20.6) 12S .224 (5.7) .812 (20.6) 12 .750 (19.1) 14S .562 (14.3) .906 (23.0) .938 (23.8) .263 (6.7) .906 (23.0) 14 .750 (19.1) 16S .562 (14.3) 1.032 (26.2) 1.062 (27.0) .325 (8.3) .969 (24.6) 16 .750 (19.1) 18 1.156 (29.4) 1.188 (30.2) .385 (9.8) 1.062 (27.0) 20 1.282 (32.6) 1.312 (33.3) .46
14、3 (11.8) 1.156 (29.4) 22 1.406 (35.7) 1.438 (36.5) .510 (13.0) 1.250 (31.8) 24 .812 (20.6) 1.532 (38.9) 1.562 (39.7) .573 (14.6) 1.375 (34.9) 28 1.782 (45.3) 1.812 (46.0) .683 (17.3) 1.562 (39.7) 32 .875 (22.2) 2.032 (51.6) 2.062 (52.4) .808 (20.5) 1.750 (44.5) 36 2.282 (58.0) 2.312 (58.7) .915 (23.
15、2) 1.938 (49.2) 40 2.532 (64.3) 2.562 (65.1) 1.023 (26.0) 2.188 (55.6) 44 4/ 2.782 (70.7) 2.812 (71.4) 1.150 (29.2) 2.375 (60.3) 48 4/ 3.032 (77.0) 3.062 (77.8) 1.275 (32.4) 2.625 (66.7) SHELL SIZE S .031 (0.8) LENGTH SIDE T +.010 (0.3)/-.005 (0.1) MOUNTING BOLT HOLE CLASS A & C CLASS K 8S .875 (22.
16、2) .120 (3.0) .150 (3.8) 10S 1.000 (25.4) 10SL 12S 1.094 (27.8) 12 14S 1.188 (30.2) 14 16S 1.281 (32.5) 16 18 1.375 (34.9) .177 (4.5) 20 1.500 (38.1) 22 1.625 (41.3) 24 1.750 (44.5) .147 (3.7) 28 2.000 (50.8) 32 2.250 (57.2) .173 (4.4) .208 (5.3) 36 2.500 (63.5) 40 2.750 (69.9) 44 4/ 3.000 (76.2) 48
17、 4/ 3.250 (82.6) 1/ WHERE RESILIENT INSERTS ARE USED, JJ MAY BE .109 (2.8) LESS THAN INDICATED. 2/ SOCKET INSERT OF HARD MATERIAL SHALL EXTEND .016 (0.4) BEYOND OR .032 (0.8) MAXIMUM BELOW SHELL. SOCKET INSERT OF RESILIENT MATERIAL SHALL EXTEND .047 (1.2) +.000/-.047 (+0.00/-1.19) BEYOND SHELL AS SH
18、OWN. SOCKET INSERT FOR CLASS K SHALL EXTEND .016 (0.4) BEYOND OR .032 (0.8) MAXIMUM BELOW SHELL. 3/ FOR SHELL SIZE 36 THROUGH 48 N TOLERANCE IS +.000/-.250 (6.4). 4/ NOT AVAILABLE FOR CLASS K. AEROSPACE STANDARD AS SHEET 4 OF 6 REV. C CONNECTOR, RECEPTACLE, ELECTRIC, BOX MOUNTING, SOLDER CONTACTS, A
19、N TYPE FIGURE 2 - CONNECTOR CONFIGURATION AND DIMENSIONS AEROSPACE STANDARD AS SHEET 5 OF 6 REV. C CONNECTOR, RECEPTACLE, ELECTRIC, BOX MOUNTING, SOLDER CONTACTS, AN TYPE TABLE 2 - FIGURE 2 DIMENSIONS SHELL SIZE A COUPLING THREAD B MIN USABLE THREAD D +.015 (0.4) -.000 (0.000) INSIDE DIA I MAX INSER
20、T DIA J +.031 (0.8) -.000 (0.000) INSERT LOCATION JJ 1/ +.031 (0.8) -.000 (0.000) INSERT LOCATION K THICKNESS MOUNTING FLANGE L MAX OVERALL LENGTH MAX MIN 8S 1/2 - 28 .375 (9.5) .370 (9.4) .250 (6.4) .562 (14.3) .484 (12.3) .156 (4.0) .078 (2.0) 1.188 (30.2) 10S 5/8 - 24 .448 (11.4) .320 (8.1) 10SL
21、.448 (11.4) 12S 3/4 - 20 .557 (14.1) 12 .625 (15.9) .750 (19.1) .672 (17.1) 1.625 (41.3) 14S 7/8 - 20 .375 (9.5) .682 (17.3) .525 (13.3) .562 (14.3) .484 (12.3) 1.188 (30.2) 14 .625 (15.9) .750 (19.1) .672 (17.1) 1.625 (41.3) 16S 1 - 20 .375 (9.5) .807 (20.5) .650 (16.5) .562 (14.3) .484 (12.3) 1.18
22、8 (30.2) 16 .625 (15.9) .750 (19.1) .672 (17.1) 1.625 (41.3) 18 1-1/8 - 18 .932 (23.7) .770 (19.6) .203 (5.2) .094 (2.4) 1.938 (49.2) 20 1-1/4 - 18 1.058 (26.9) .925 (23.5) 22 1-3/8 - 18 1.182 (30.0) 1.020 (25.9) 24 1-1/2 - 18 1.307 (33.2) 1.145 (29.1) 28 1-3/4 - 18 1.526 (38.8) 1.365 (34.7) 32 2 -
23、18 1.776 (45.1) 1.615 (41.0) .359 (9.1) .126 (3.2) 36 2-1/4 - 16 1.995 (50.7) 1.830 (46.5) 40 2-1/2 - 16 2.245 (57.0) 2.045 (51.9) 1/ WHERE RESILIENT INSERTS ARE USED, JJ MAY BE .109 (2.8) LESS THAN INDICATED. SHELL SIZE M +.031 (0.8) -.000 (0.0) MTG. FLANGE LOCATION N 2/ +.000 (0.0) -.188 (4.8) OUT
24、SIDE DIA O REF MOUNTING HOLE P +.015 (0.4) -.000 (0.0) KEY HEIGHT R .005 (0.1) CC - CL MTG. HOLE S .031 (0.8) LENGTH SIDE T +.010 (0.3) -.005 (0.1) MOUNTING BOLT HOLE 8S .562 (14.3) .532 (13.5) .562 (14.2) .130 (3.3) .594 (15.1) .875 (22.2) .120 (3.0) 10S .656 (16.7) .688 (16.7) .165 (4.2) .719 (18.
25、3) 1.000 (25.4) 10SL .782 (19.9) .812 (20.6) 12S .224 (5.7) .812 (20.6) 1.094 (27.8) 12 .750 (19.1) 14S .562 (14.3) .906 (23.0) .938 (23.8) .263 (6.7) .906 (23.0) 1.188 (30.2) 14 .750 (19.1) 16S .562 (14.3) 1.032 (26.2) 1.062 (27.0) .325 (8.3) .969 (24.6) 1.281 (32.5) 16 .750 (19.1) 18 1.156 1.188 .
26、385 (9.8) 1.062 (27.0) 1.375 (34.9) 20 1.282 1.312 .463 (11.8) 1.156 (29.4) 1.500 (38.1) 22 1.406 1.438 .510 (13.0) 1.250 (31.8) 1.625 (41.3) 24 .812 (20.6) 1.532 1.562 .573 (14.6) 1.375 (34.9) 1.750 (44.5) .147 (3.7) 28 1.782 1.812 .683 (17.3) 1.562 (39.7) 2.000 (50.8) 32 .875 (22.2) 2.032 2.062 .8
27、08 (20.5) 1.750 (44.5) 2.250 (57.2) .173 (4.4) 36 2.282 2.312 .915 (23.2) 1.938 (49.2) 2.500 (63.5) 40 2.532 2.512 1.023 (26.0) 2.188 (55.6) 2.750 (69.9) 2/ FOR SHELL SIZE 36 AND 40 N TOLERANCE IS +.000/-.250 (6.4). AEROSPACE STANDARD AS SHEET 6 OF 6 REV. C CONNECTOR, RECEPTACLE, ELECTRIC, BOX MOUNT
28、ING, SOLDER CONTACTS, AN TYPE REQUIREMENTS: ALL REQUIREMENTS SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS50151. 1. DESIGN: THE CONNECTORS SHALL BE DESIGNED IN ACCORDANCE WITH FIGURES 1 AND 2 AND TABLES 1 AND 2. DIMENSIONS ARE IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: DECIMALS .
29、016 (0.4). METRIC EQUIVALENTS ARE GIVEN FOR GENERAL INFORMATION ONLY AND ARE BASED UPON 1 INCH = 25.4 MM (MILLIMETERS ARE IN PARENTHESES). 2. MATERIAL: IN ACCORDANCE WITH AS50151. 3. PART OR IDENTIFYING NUMBER (PIN) EXAMPLE: SEE BELOW MS3102 A 18 - 5 S Y BASIC PART NUMBER CLASS (A, C, K, E, AND R) S
30、HELL SIZE INSERT ARRANGEMENT NUMBER STYLE (P OR S) ALTERNATE INSERT POSITION (W, X, Y, OR Z) LEAVE BLANK FOR NORMAL POSITION 4. CONNECTORS MS3102 REPLACE AND ARE INTERCHANGEABLE WITH CORRESPONDING AN3102 CONNECTORS OF THE SAME CLASS. 5. INSERT ARRANGEMENTS SHALL BE IN ACCORDANCE WITH MIL-STD-1651. A
31、PPLICATION NOTES 1. THE FRONT FACE OF THIS CONNECTOR (CLASS R) PROVIDES ENVIRONMENTAL SEALING WHEN COUPLED TO ITS CORRESPONDING PLUG CONNECTOR. THE REAR OF THIS CONNECTOR IS NON-ENVIRONMENTAL AND THE CONNECTOR IS INTENDED FOR USE ON BOXES WHERE THE REAR ENVIRONMENTAL SEAL IS ACHIEVED BY SOME OTHER M
32、EANS. 2. SIZES 8S THROUGH 40 OF CLASSES A AND C ARE CANCELLED AFTER 1 JANUARY 1991. FOR REPLACEMENT PURPOSES, USE MS3102R, FOR NEW DESIGN USE MS3452W. 3. SIZES 44 AND 48 OF CLASSES A AND C ARE NOT RECOMMENDED FOR NEW DESIGN. 4. CLASS K AND R ARE INACTIVE FOR NEW DESIGN AFTER 1 JANUARY 1991. FOR NEW
33、DESIGN CLASS R USE MS3452W. FOR NEW DESIGN CLASS K USE MS3452K. FOR SHIPBOARD JACKETED CABLE USE MS3402. 5. CLASS E IS CANCELLED AFTER 1 JANUARY 1991. FOR REPLACEMENT PURPOSES USE MS3102R. FOR NEW DESIGN USE MS3452W. FOR SHIPBOARD JACKETED CABLE USE MS3402. SPECIFICATION NOTES 1. REVISION INDICATOR:
34、 A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
