1、 AEROSPACE STANDARD FITTING ASSEMBLY, TEE, AXIALLY SWAGED ON THE RUN, MALE FLARELESS ON THE SIDE, HYDRAULIC, UP TO 1500 PSI AS6123Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any me
2、ans, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org
3、ISSUED 2011-07REVISED 2015-06THIRD ANGLE PROJECTION CUSTODIAN: G-3/G-3B REV.A FEDERAL SUPPLY CLASS 4730AS6123 SHEET 1 OF 4 REV. A PROCUREMENT SPECIFICATION: /4/ AS6116SAE Technical Standards Board Rules provide that: “This report ispublished by SAE toadvance thestate of technicalandengineering scien
4、ces. Theuse ofthisreport is entirelyvoluntary, andits applicability and suitability forany particularuse,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabil
5、ized, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS6123A RATIONALE ADDED STANDARD CONFIGURATION 242424. FIGURE 1 - FITTING ASSEMBLY, TEE, AXIALLY SWAGED ON THE RUN
6、 MALE FLARELESS ON THE SIDE AEROSPACE STANDARD AS6123 SHEET 2 OF 4 REV. A FITTING ASSEMBLY, TEE, AXIALLY SWAGED ON THE RUN, MALE FLARELESS ON THE SIDE, HYDRAULIC, UP TO 1500 PSI TABLE 1A - DIMENSIONS A THROUGH EA BASIC NO. AS6123 /15/ SIZE CODE NOMINAL TUBE SIZE END 1 NOMINAL TUBE SIZE END 2 NOMINA
7、L TUBE SIZE END 3 A MAX A1 MAX B MAX B1 MAX C .015 E MAX EA MAX 040404 .250 .250 .250 1.112 .959 1.112 .959 .767 .435 .435 050505 .3125 .3125 .3125 1.258 1.110 1.258 1.110 .786 .503 .503 060606 .375 .375 .375 1.464 1.237 1.464 1.237 .846 .580 .580 080808 .500 .500 .500 1.765 1.505 1.765 1.505 1.032
8、755 .755 100808 .625 .500 .500 1.780 1.540 1.765 1.505 1.095 .929 .755 101008 .625 .625 .500 1.780 1.540 1.780 1.540 1.095 .929 .929 101010 .625 .625 .625 1.843 1.603 1.843 1.603 1.158 .929 .929 101012 .625 .625 .750 1.968 1.728 1.968 1.728 1.331 .929 .929 101016 .625 .625 1.000 2.093 1.853 2.093 1
9、853 1.465 .929 .929 121206 .750 .750 .375 2.103 1.823 2.103 1.823 1.112 1.150 1.150 121212 .750 .750 .750 2.103 1.823 2.103 1.823 1.346 1.150 1.150 161616 1.000 1.000 1.000 2.618 2.238 2.618 2.238 1.505 1.474 1.474 202020 1.250 1.250 1.250 3.069 2.654 3.069 2.654 1.627 1.768 1.768 242424 1.500 1.50
10、0 1.500 3.600 3.105 3.600 3.105 1.747 2.070 2.070 TABLE 1B - DIMENSIONS F THROUGH JA BASIC NO. AS6123 /15/ SIZE CODE NOMINAL TUBE SIZE END 1 NOMINAL TUBE SIZE END 2 NOMINAL TUBE SIZE END 3 F MIN FA MIN G .015 J /12/ TUBE DEDUCTION JA /12/ TUBE DEDUCTION 040404 .250 .250 .250 .253 .253 .438 .419 +.15
11、0/-.180 .419 +.150/-.180 050505 .3125 .3125 .3125 .3155 .3155 .465 .435 +.150/-.180 .435 +.150/-.180 060606 .375 .375 .375 .378 .378 .563 .492 +.150/-.195 .492 +.150/-.195 080808 .500 .500 .500 .503 .503 .750 .590 +.150/-.210 .590 +.150/-.210 100808 .625 .500 .500 .629 .503 .875 .600 +.150/-.200 .59
12、0 +.150/-.210 101008 .625 .625 .500 .629 .629 .875 .600 +.150/-.200 .600 +.150/-.200 101010 .625 .625 .625 .629 .629 .875 .663 +.150/-.200 .663 +.150/-.200 101012 .625 .625 .750 .629 .629 1.063 .788 +.150/-.200 .788 +.150/-.200 101016 .625 .625 1.000 .629 .629 1.304 .913 +.150/-.200 .913 +.150/-.200
13、 121206 .750 .750 .375 .754 .754 1.063 .783 +.150/-.245 .783 +.150/-.245 121212 .750 .750 .750 .754 .754 1.063 .783 +.150/-.245 .783 +.150/-.245 161616 1.000 1.000 1.000 1.004 1.004 1.304 .928 +.150/-.330 .928 +.150/-.330 202020 1.250 1.250 1.250 1.255 1.255 1.618 1.104 +.150/-.375 1.104 +.150/-.375
14、 242424 1.500 1.500 1.500 1.505 1.505 1.806 1.275 +.150/-.425 1.275 +.150/-.425 TABLE 1C - DIMENSIONS T THROUGH W1A BASIC NO. AS6123 /15/ SIZE CODE NOMINAL TUBE SIZE END 1 NOMINAL TUBE SIZE END 2 NOMINAL TUBE SIZE END 3 ( T ) THREAD PER AS8879 W MIN WA MIN W1 MAX W1A MAX 040404 .250 .250 .250 .4375-
15、20 UNJF-3A .185 .185 .604 .604 050505 .3125 .3125 .3125 .5000-20 UNJF-3A .180 .180 .724 .724 060606 .375 .375 .375 .5625-18 UNJF-3A .195 .195 .883 .883 080808 .500 .500 .500 .7500-16 UNJF-3A .210 .210 1.076 1.076 100808 .625 .500 .500 .7500-16 UNJF-3A .225 .210 1.076 1.076 101008 .625 .625 .500 .750
16、0-16 UNJF-3A .225 .225 1.076 1.076 101010 .625 .625 .625 .8750-14 UNJF-3A .225 .225 1.076 1.076 101012 .625 .625 .750 1.0625-12 UNJ-3A .225 .225 1.076 1.076 101016 .625 .625 1.000 1.3125-12 UNJ-3A .225 .225 1.076 1.076 121206 .750 .750 .375 .5625-18 UNJF-3A .235 .235 1.201 1.201 121212 .750 .750 .75
17、0 1.0625-12 UNJ-3A .235 .235 1.201 1.201 161616 1.000 1.000 1.000 1.3125-12 UNJ-3A .260 .260 1.566 1.566202020 1.250 1.250 1.250 1.6250-12 UNJ-3A .285 .285 1.829 1.829 242424 1.500 1.500 1.500 1.8750-12 UNJ-3A .310 .310 2.178 2.178AEROSPACE STANDARD AS6123 SHEET 3 OF 4 REV. A FITTING ASSEMBLY, TEE,
18、AXIALLY SWAGED ON THE RUN, MALE FLARELESS ON THE SIDE, HYDRAULIC, UP TO 1500 PSI TABLE 1D - DIMENSIONS W2 THROUGH W4A AND WEIGHTS BASIC NO. AS6123 /15/ SIZE CODE NOMINAL TUBE SIZE END 1 NOMINAL TUBE SIZE END 2 NOMINAL TUBE SIZE END 3 W2 .002 W2A .002 W3 MAX W3A MAX W4 MAX W4A MAX WEIGHT APPROX LB/EA
19、 040404 .250 .250 .250 .320 .320 .020 .020 .020 .020 .020 050505 .3125 .3125 .3125 .371 .371 .020 .020 .020 .020 .025 060606 .375 .375 .375 .463 .463 .020 .020 .020 .020 .040 080808 .500 .500 .500 .595 .595 .020 .020 .020 .020 .080 100808 .625 .500 .500 .758 .595 .020 .020 .020 .020 .100 101008 .625
20、 .625 .500 .758 .758 .020 .020 .020 .020 .105 101010 .625 .625 .625 .758 .758 .020 .020 .020 .020 .115 101012 .625 .625 .750 .758 .758 .020 .020 .020 .020 .170 101016 .625 .625 1.000 .758 .758 .020 .020 .020 .020 .255 121206 .750 .750 .375 .903 .903 .025 .025 .025 .025 .190 121212 .750 .750 .750 .90
21、3 .903 .025 .025 .025 .025 .200 161616 1.000 1.000 1.000 1.196 1.196 .035 .035 .035 .035 .365 202020 1.250 1.250 1.250 1.460 1.460 .035 .035 .035 .035 .580 242424 1.500 1.500 1.500 1.704 1.704 .035 .035 .035 .035 .700 NOTES: /1/ MATERIALS: CODE LETTER “D“ BODY - TYPE 6061-T6 ALUMINUM ALLOY BAR PER A
22、MS-QQ-A-225/8. RING - TYPE 7075-T73 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/9. 2. FINISH: BODY - CHEMICAL CONVERSION COATED PER MIL-DTL-5541 TYPE I CLASS 3. RINGS - ANODIZE PER MIL-A-8625, TYPE II, CLASS 2, DYED GREEN, SIMILAR TO NO. 14187, 14193, OR 14223 OF FED-STD-595 AND SHALL BE DUPLEX SEALED. /3/
23、COATINGS/LUBRICANTS: BODY a. DRY FILM LUBRICANT PER AS5272 TYPE I SHALL BE APPLIED TO THE OD OF THE AXIALLY SWAGED FITTING END. ADDITIONAL LUBRICANT APPLIED SHALL BE SPECIFIED BY MANUFACTURER. THE LUBRICANTS SHALL NOT BE IN CONTACT WITH THE SYSTEM FLUID. b. POLYTETRAFLUOROETHYLENE (PTFE) COAT, LIGHT
24、 GREEN, SHALL BE APPLIED TO PORTIONS OF ID (BORE) UP TO THE FIRST GROOVE. OVERSPRAY IN GROOVE IS NOT PERMITTED. c. A MINIMUM OF TWO GROOVES (END SIZE -05 AND LARGER) SHALL BE FILLED WITH ELASTOMERIC DIMETHYL SILOXANE COMPOUND. FOR SMALLER SIZE ENDS, A MINIMUM OF ONE GROOVE SHALL BE FILLED WITH THE C
25、OMPOUND. /4/ PROCUREMENT SPECIFICATION: AS6116 EXCEPT AS SPECIFIED ON THIS STANDARD. PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST (QPL) PRI-QPL-AS6116 FOR THIS STANDARD. SEE www.eAu
26、ditN FOR THE CURRENT QPL ON-LINE. 5. DIMENSIONS AND TOLERANCES NOT DEFINED ON THIS STANDARD SHALL BE SPECIFIED AND CONTROLLED BY THE MANUFACTURER. THE MANUFACTURER IS RESPONSIBLE TO ENSURE COMPLIANCE WITH THE PROCUREMENT SPECIFICATION. /6/ IDENTIFICATION SHALL BE IN ACCORDANCE WITH AS6116 AND SHALL
27、BE IDENTIFIED ON EITHER RING IN THE AREA SHOWN. FOR SIZE -05 AND LARGER, THE RING OD SHALL HAVE TWO GROOVES INDICATING DUAL SEALING BACK UP FEATURE. 7. FITTINGS SHALL BE INSTALLED IN ACCORDANCE WITH AS6124. 8. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE S
28、PECIFIED, THE MAXIMUM MACHINED SURFACES SHALL BE 125 MICROINCHES Ra. AEROSPACE STANDARD AS6123 SHEET 4 OF 4 REV. A FITTING ASSEMBLY, TEE, AXIALLY SWAGED ON THE RUN, MALE FLARELESS ON THE SIDE, HYDRAULIC, UP TO 1500 PSI 9. BREAK ALL EDGES .003 TO .010 INCHES UNLESS OTHERWISE SPECIFIED. 10. DIMENSIONI
29、NG AND TOLERANCING: ASME Y14.5M-1994. 11. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .015, ANGULAR DIMENSIONS 0 30. /12/ DIMENSIONS “J” AND “JA” ARE THE ALLOWABLE TUBE END POSITIONING FOR SYSTEM LAYOUT DESIGN. /13/ DIMENSIONS “A” AND “B” ARE THE FITTING ASSEMBLY
30、LENGTHS PRIOR TO SWAGE AND “A1” AND “B1” ARE THE AFTER SWAGE ASSEMBLY LENGTHS MEASURED FROM THE SWAGED RINGS. /14/ PARTS FOR OXYGEN SYSTEMS SHALL BE IDENTIFIED IN THE PART NUMBER AS SUFFIX CODE “A” AND SHALL BE FURNISHED CLEANED, PACKAGED, AND LABELED IN ACCORDANCE WITH ARP1176 CATEGORY 1A. /15/ EXA
31、MPLE OF PART NUMBER: AS6123 D 10 08 08 A OPTIONAL OXYGEN CLEANING /14/ BASIC PART NUMBER END 3 SIZE CODE IN .062 INCH INCREMENTS(08 = .500 INCH) MATERIAL CODE LETTER /1/ END 2 SIZE CODE IN .062 INCH INCREMENTS (08 = .500 INCH) END 1 SIZE CODE IN .062 INCH INCREMENTS (10 = .625 INCH) 16. A CHANGE BAR
32、 (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
