1、 AEROSPACE STANDARD CONNECTOR ACCESSORIES, ELECTRICAL, MOUNTING DEVICE, FLANGE TYPE, CATEGORY 7, 3/4 PERIMETER AS85049/95Copyright 2016 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, elec
2、tronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED200
3、1-07REVISED2011-04REAFFIRMED2016-08THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C1 REV.C FEDERAL SUPPLY CLASS 5935 AS85049/95 SHEET 1 OF 5 REV. C PROCUREMENT SPECIFICATION: AS85049 SAE Technical StandardsBoardRulesprovidethat:“ThisreportispublishedbySAE toadvancethestateoftechnicalandengineering scien
4、ces. The use of thisreport isentirelyvoluntary, andits applicability andsuitability for any particularuse, includingany patent infringement arising therefrom,is the soleresponsibility of theuser.”SAE reviewseachtechnical reportatleasteveryfiveyearsatwhichtimeitmayberevised,reaffirmed,stabilized,orca
5、ncelled. SAEinvites yourwritten comments andsuggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AS85049/95C RATIONALE AS85049/95C HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. NOTICE THE REQUIREMENT
6、S FOR ACQUIRING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS SPECIFICATION SHEET AND THE LATEST ISSUE OF SAE AS85049. FIGURE 1 CONFIGURATION AND DIMENSIONS AEROSPACE STANDARD AS85049/95 SHEET 2 OF 5 CONNECTOR ACCESSORIES, ELECTRICAL, MOUNTING DEVICE, FLANGE TYPE, CATEGORY 7, 3/4 PERIMETER REV.
7、 C TABLE 1 - DIMENSIONS DASH NUMBER CLASS THRD UNJC -3B A .005 1/ B MAX 1/ C .015 D E .030 1/ 3 A 4-40 .625 (15.88) .940 (23.88) .641 (16.28) .106 (2.69) .166 (4.22) .325 (8.26) 7 A 4-40 .719 (18.26) 1.034 (26.26) .688 (17.48) .106 (2.69) .166 (4.22) .433 (11.00) 8 A 4-40 .594 (15.09) .900 (22.86) .
8、570 (14.48) .106 (2.69) .166 (4.22) .308 (7.82) 10 A 4-40 .719 (18.26) 1.034 (26.26) .720 (18.29) .106 (2.69) .166 (4.22) .433 (11.00) B 6-32 .812 (20.62) 1.202 (30.53) .749 (19.02) .123 (3.12) .183 (4.65) 12 A 4-40 .812 (20.62) 1.119 (28.42) .855 (21.72) .106 (2.69) .166 (4.22) .530 (13.46) B 6-32
9、938 (23.83) 1.327 (33.71) .938 (23.83) .123 (3.12) .183 (4.65) 14 A 4-40 .906 (23.01) 1.213 (30.81) .984 (24.99) .106 (2.69) .166 (4.22) .624 (15.85) B 6-32 1.031 (26.19) 1.421 (36.09) 1.031 (26.19) .123 (3.12) .183 (4.65) 16 A 4-40 .969 (24.61) 1.295 (32.89) 1.094 (27.79) .106 (2.69) .166 (4.22) .
10、687 (17.45) B 6-32 1.125 (28.58) 1.515 (38.48) 1.125 (28.58) .123 (3.12) .183 (4.65) 18 A 4-40 1.062 (26.97) 1.421 (36.09) 1.220 (30.99) .106 (2.69) .166 (4.22) .780 (19.81) B 6-32 1.203 (30.56) 1.593 (40.46) 1.234 (31.34) .123 (3.12) .183 (4.65) 19 A 4-40 .906 (23.01) 1.207 (30.66) .953 (24.21) .10
11、6 (2.69) .166 (4.22) .620 (15.75) 20 A 4-40 1.156 (29.36) 1.550 (39.37) 1.345 (34.16) .106 (2.69) .166 (4.22) .874 (22.20) B 6-32 1.297 (32.94) 1.703 (43.26) 1.359 (34.52) .123 (3.12) .183 (4.65) .865 (21.97) 22 A 4-40 1.250 (31.75) 1.680 (42.67) 1.478 (37.54) .106 (2.69) .166 (4.22) .968 (24.59) B
12、6-32 1.375 (34.93) 1.753 (44.53) 1.483 (37.67) .123 (3.12) .183 (4.65) .907 (23.04) 24 A 6-32 1.500 (38.10) 1.906 (48.41) 1.560 (39.62) .106 (2.69) .166 (4.22) 1.000 (25.40) B 6-32 1.375 (34.93) 1.800 (45.72) 1.595 (40.51) .123 (3.12) .183 (4.65) 1.031 (26.19) 25 A 6-32 1.500 (38.10) 1.906 (48.41) 1
13、658 (42.11) .123 (3.12) .183 (4.65) 1.125 (28.58) 27 A 4-40 .969 (24.61) 1.270 (32.26) 1.094 (27.79) .106 (2.69) .166 (4.22) .683 (17.35) 28 A 6-32 1.562 (39.67) 2.015 (51.18) 1.820 (46.23) .123 (3.12) .183 (4.65) 1.125 (28.58) 32 A 6-32 1.750 (44.45) 2.327 (59.11) 2.062 (52.37) .123 (3.12) .183 (4
14、65) 1.188 (30.18) 36 A 6-32 1.938 (49.23) 2.515 (63.88) 2.312 (58.72) .123 (3.12) .183 (4.65) 1.375 (34.93) 37 A 4-40 1.187 (30.15) 1.515 (38.48) 1.281 (32.54) .106 (2.69) .166 (4.22) .874 (22.20) 61 A 4-40 1.437 (36.50) 1.827 (46.41) 1.594 (40.49) .106 (2.69) .166 (4.22) 1.062 (40.69) 1/ DIMENSION
15、S A, B AND E SHALL BE MEASURED WITH THE MOUNTING FLANGE IN THE RESTRAINED STATE AEROSPACE STANDARD AS85049/95 SHEET 3 OF 5 CONNECTOR ACCESSORIES, ELECTRICAL, MOUNTING DEVICE, FLANGE TYPE, CATEGORY 7, 3/4 PERIMETER REV. C NOTES: 1. DIMENSIONS ARE INCHES. 2. UNLESS OTHERWISE SPECIFIED, TOLERANCE IS .0
16、10. 3. CLASSES REPRESENT SHELL SIZE VARIATIONS (SEE TABLE 1). 4. FOR MOUNTING FLANGE CROSS REFERENCE INFORMATION, SEE TABLE 2. REQUIREMENTS: DESIGN AND CONSTRUCTION: 1. DIMENSIONS AND CONFIGURATION SHALL BE IN ACCORDANCE WITH FIGURE 1, TABLE 1. 2. FIGURE 1, MOUNTING FLANGES SHALL BE OF A CONSTRUCTIO
17、N WITH PREDRILLED OR PUNCHED HOLES IN ALUMINUM ALLOY INCORPORATING SELF LOCKING NUTS, CLINCH TYPE. 3. MATERIAL AND FINISH: FLANGES, ALUMINUM ALLOY IN ACCORDANCE WITH SAE AS85049, CHEMICAL CONVERSION COATING PER MIL-DTL-5541, CLASS 1A. WHEN SPECIFIED IN THE PART NUMBER, BY LETTER A DESIGNATOR, 2 COAT
18、S OF EPOXY POLYAMIDE PRIMER PER MIL-PRF-23377, TYPE I, SHALL BE APPLIED EITHER BEFORE OR AFTER NUT INSTALLATION AND OVERSPRAY IS ALLOWED PROVIDED THE PERFORMANCE CHARACTERISTICS OF THE NUT ARE NOT DEGRADED AND ALL OTHER REQUIREMENTS ARE MET. 4. CLINCH NUTS: IN ACCORDANCE WITH NASM45938, CLEAN AND DE
19、SCALE IN ACCORDANCE WITH ASTM A 380 AND/OR PASSIVATED IN ACCORDANCE WITH AMS-QQ-P-35 OR AMS2700, FOLLOWED BY A SOLID FILM LUBRICANT COATING PER MIL-PRF-46010. 5. PART NUMBER: SEE EXAMPLE BELOW. EXAMPLE: M85049/ 95 - 8A - A BASIC PART NUMBER SPECIFICATION SHEET DASH NUMBER (SEE TABLE 1) PART COAT RE
20、QUIRED (SEE REQUIREMENT 3) 6. PARAGRAPH 6.1 PERIODIC QUALIFICATION: SEE AS85049, CATEGORY 7, WITH THE FOLLOWING ADDITIONS: A. LOCKING TORQUE IN ACCORDANCE WITH NASM25027. B. TORQUE OUT IN ACCORDANCE WITH NASM45938, EXCEPT THE REQUIREMENT SHALL BE 15 IN LBS MINIMUM FOR 4-40 THREADED NUTS AND 20 IN LB
21、S MINIMUM FOR 6-32 THREADED NUTS. C. PUSH OUT IN ACCORDANCE WITH NASM45938, EXCEPT THE REQUIREMENT SHALL BE 88 LB MINIMUM FOR 4-40 THREADED NUTS AND 105 LB MINIMUM FOR 6-32 THREADED NUTS. D. POST EXAMINATION. AEROSPACE STANDARD AS85049/95 SHEET 4 OF 5 CONNECTOR ACCESSORIES, ELECTRICAL, MOUNTING DEVI
22、CE, FLANGE TYPE, CATEGORY 7, 3/4 PERIMETER REV. C TABLE 2 - MOUNTING FLANGE CONNECTOR APPLICATION DATA 1/ AS85049/95 DASH NUMBER/CLASS MIL-DTL-38999 MIL-DTL-5015 AS81703 SERIES 3 SERIES I SERIES II SERIES III SERIES IV CONNECTOR SHELL SIZE 3A 3 7A 7 8A 8 8S 10A 9 10 9 (A) 10SL 10B 12A 11 12 11 (B) 1
23、1 (B) 12, 12S 12 12B 14A 13 14 13 (C) 13 (C) 14, 14S 19 14B 16A 15 16 15 (D) 15 (D) 16, 16S 27 16B 18A 17 18 17 (E) 17 (E) 18 18B 20A 19 20 19 (F) 19 (F) 20 20B 22A 21 22 21 (G) 21 (G) 22 22B 24A 24B 23 24 23 (H) 23 (H) 24 25A 25 25 (J) 25 (J) 27A 28A 28 32A 36A 37A 37 61A 61 AEROSPACE STANDARD AS85
24、049/95 SHEET 5 OF 5 CONNECTOR ACCESSORIES, ELECTRICAL, MOUNTING DEVICE, FLANGE TYPE, CATEGORY 7, 3/4 PERIMETER REV. C TABLE 2 - MOUNTING FLANGE CONNECTOR APPLICATION DATA 1/ (CONTINUED) AS85049/95 DASH NUMBER/ CLASS MIL-DTL-26482 SERIES 1 & 2 MIL-DTL-83723 SERIES III MIL-DTL-26500 NAS 1599 MIL-C-815
25、11 MIL-DTL-27599CONNECTOR SHELL SIZE 3A 7A 8A 8 8 8 8 8 10A 10 10 10 10 10 10B 12A 12 12 12 12 12B 14A 14 14 14 14 14 14B 16A 16 16 16 16 16 16B 18A 18 18 18 18 18 18B 20A 20 20 20 20 20 20B 22A 22 22 22 22 22 22B 24A 24B 24 24 24 24 24 25A 27A 28A 32A 36A 37A 61A 1/ THE INFORMATION ABOVE IS SHOWN F
26、OR REFERENCE ONLY. IT IS RECOMMENDED THE USER VERIFY CONNECTOR/ MOUNTING FLANGE DETAIL SHEETS FOR COMPATIBILITY SINCE SOME CONNECTOR SHELL SIZES AND CLASSES MAY NOT BE APPLICABLE. 7. SPECIFICATION NOTES A CHANGE BAR (|) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS
27、WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
