1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA
2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any
3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-23656-4 SANS 1639:2010Edition 2SOUTH AFRICAN NATIONAL STANDARD Reconditioned pneumatically powered chain hoists Published by SABS Standard
4、s Division 1 Dr Lategan Road Groenkloof Private Bag X191 Pretoria 0001Tel: +27 12 428 7911 Fax: +27 12 344 1568 www.sabs.co.za SABS SANS 1639:2010 Edition 2 Table of changes Change No. Date Scope Foreword This South African standard was approved by National Committee SABS TC 1020, Lifting equipment,
5、 in accordance with procedures of the SABS Standards Division, in compliance with annex 3 of the WTO/TBT agreement. This document was published in March 2010. This document supersedes SANS 1639:2008 (edition 1.2). Reference is made in 3.1 to the “relevant national legislation“. In South Africa this
6、means the Engineering Profession Act, 2000 (Act no. 46 of 2000). Annex A forms an integral part of this document. SANS 1639:2010 Edition 2 1 Contents Page Foreword 1 Scope. 3 2 Normative references 3 3 Definitions 3 4 Quality management requirements . 4 5 Before reconditioning. 4 6 Reconditioning re
7、quirements. 4 7 Apparatus. 5 8 Methods of test 5 9 Documentation and test certificates 6 Annex A (normative) Notes to customers. 8 SANS 1639:2010 Edition 2 2 This page is intentionally left blank SANS 1639:2010 Edition 2 3 Reconditioned pneumatically powered chain hoists 1 Scope This standard specif
8、ies repair and test requirements for the reconditioning of pneumatically powered chain hoists. All repairs performed in accordance with this standard comply with the original manufacturers specifications and SANS 1638. 2 Normative references The following referenced document is indispensable for the
9、 application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. Information on currently valid national and international standards can be obtained from the SABS Standards D
10、ivision. SANS 1638, Pneumatically powered chain hoists. 3 Definitions For the purposes of this document, the definitions given in SANS 1638 and the following apply. 3.1 competent person person with the knowledge, training, experience and qualifications specific to the work or task being performed as
11、 specified in the relevant national legislation (see foreword) 3.2 original manufacturers specification specification in accordance with which the pneumatically powered chain hoist was originally manufactured 3.3 reconditioner person, body of persons or company contracted to recondition pneumaticall
12、y powered chain hoists in accordance with this standard 3.4 reconditioning repair of pneumatically powered chain hoists in accordance with the original manufacturers specification SANS 1639:2010 Edition 2 4 4 Quality management requirements 4.1 General The quality management system of the reconditio
13、ner shall comply with the applicable provisions of SANS 1638. 4.2 Control of non-compliant material Any material deemed unsuitable for incorporation into reconditioned pneumatically powered chain hoists shall immediately be identified as such by an appropriate method. Such material shall then be so
14、segregated that it cannot be used inadvertently until its disposition is determined. Such material shall be disposed of as agreed upon (see annex A). 4.3 Control of inspection, measuring and testing equipment The reconditioner shall provide and maintain sufficient calibrated (in accordance with an a
15、greed national or international standard) inspection, measuring and testing equipment to demonstrate compliance with the relevant requirements of this standard. 5 Before reconditioning When identifying pneumatically powered chain hoists to be reconditioned, the following details shall be recorded: a
16、) the traceable reference number of the hoist; b) the customer name; c) the name of the original manufacturer; d) the brand name; e) the type of product; and f) the working load limit (WLL). 6 Reconditioning requirements 6.1 General When reconditioned, the pneumatically powered chain hoist shall be
17、restored to its original functional condition and performance specifications in accordance with SANS 1638. 6.2 Dismantling and cleaning Pneumatically powered chain hoists shall be completely dismantled and reduced to their component parts for initial evaluation before reconditioning is started. When
18、 dismantled, the hoist shall be cleaned of all rust, scale and foreign matter by an acceptable method to enable inspection for cracks and measurements to be taken. SANS 1639:2010 Edition 2 5 6.3 Replaced components Replaced components shall be disposed of as agreed upon between the customer and the
19、reconditioner (see annex A). 7 Apparatus Dynamic test rig, calibrated and certified every six months. 8 Methods of test 8.1 Operational test 8.1.2 Load the repaired pneumatically powered chain hoist with a test load of between 2% and 5% of the WLL. 8.1.2 Raise and lower the load through a height of
20、between 250 mm to 500 mm and apply rotational force to the load. Ensure that the hooks swivel. 8.1.3 Remove the load and operate the hoist over the entire length of load chain in both directions. The chain shall travel smoothly through the hoist and the limit devices shall be activated when the trav
21、el limits are reached. 8.2 Proof load and braking test 8.2.1 Load the repaired pneumatically powered chain hoist with a proof load equal to 125% of the WLL and conduct the test in accordance with the manufacturers specifications. 8.2.2 Raise and lower the test load of the pneumatically powered chain
22、 hoist through a minimum distance of 2 m to ensure that every part of the hoist mechanism and each part of the gearing come under load. 8.2.3 When releasing the operating control four times at random intervals while raising and lowering the load a) the brake shall immediately engage and prevent the
23、proof load from descending when the operating control is released, b) there shall be no visible defects, and c) the swivel hook shall continue to operate smoothly. 8.3 Performance test Subject each reconditioned pneumatically powered chain hoist to a) a performance test relating to the WLL, loaded l
24、ifting speed and rated air pressure in accordance with the manufacturers specification, and b) an appropriate load limiter function test, if applicable. SANS 1639:2010 Edition 2 6 9 Documentation and test certificates 9.1 General Pneumatically powered chain hoists reconditioned in accordance with th
25、is standard shall be accompanied by all the relevant documentation. 9.2 Test certificate A test certificate shall be issued for each reconditioned pneumatically powered chain hoist and shall contain at least the following information: a) the original manufacturer/brand name; b) the original serial n
26、umber or, if missing, a traceable reference number of the hoist; c) the WLL; d) the loaded lifting speed; e) the test operating air pressure range; f) the proof load; g) the range of lift; h) the load chain size and grade; i) the production batch number of the load chain; j) the batch number of the
27、top and bottom hook; k) the date and place of the test; l) a statement of compliance with this standard (for example “Reconditioned in accordance with SANS 1639”); and m) the name, trade name or trademark of the reconditioner. The competent person conducting the tests shall sign, date and record his
28、/her registration number on the certificate. 9.3. Load chain test certificate If the load chain has been replaced during the reconditioning process, a load chain test certificate shall be supplied with the reconditioned hoist. The certificate shall be numbered, signed and dated by the chain manufact
29、urer and shall contain at least the following information: a) the manufacturers name and production batch reference; b) the manufacturing proof force; c) the guaranteed minimum breaking force; SANS 1639:2010 Edition 2 7 d) the date and place of test; e) the agreed-upon standard or specification in a
30、ccordance with which the chain is manufactured (see annex A); f) the size and grade of the load chain. 9.4 Repair records The reconditioner shall keep a record/job card of all work conducted on each hoist. A completed copy of the document shall be returned with each reconditioned hoist. SANS 1639:20
31、10 Edition 2 8 Annex A (normative) Notes to customers The following requirements shall be agreed upon between the reconditioner and the customer: a) the disposal method of non-compliant material (see 4.2); b) whether the original manufacturers specification shall be SANS 1638 and the original manufa
32、cturers standard (see 9.3(a); c) how long records shall be kept if for more than five years (see 9.4); d) corrosion protection requirements; and e) whether spark resistance requirements/specifications shall be stipulated. SABS SABS Standards Division The objective of the SABS Standards Division is t
33、o develop, promote and maintain South African National Standards. This objective is incorporated in the Standards Act, 2008 (Act No. 8 of 2008). Amendments and Revisions South African National Standards are updated by amendment or revision. Users of South African National Standards should ensure tha
34、t they possess the latest amendments or editions. The SABS continuously strives to improve the quality of its products and services and would therefore be grateful if anyone finding an inaccuracy or ambiguity while using this standard would inform the secretary of the technical committee responsible
35、, the identity of which can be found in the foreword. Tel: +27 (0) 12 428 6666 Fax: +27 (0) 12 428 6928 The SABS offers an individual notification service, which ensures that subscribers automatically receive notification regarding amendments and revisions to South African National Standards. Tel: +
36、27 (0) 12 428 6883 Fax: +27 (0) 12 428 6928 E-mail: salessabs.co.za Buying Standards Contact the Sales Office for South African and international standards, which are available in both electronic and hardcopy format. Tel: +27 (0) 12 428 6883 Fax: +27 (0) 12 428 6928 E-mail: salessabs.co.za South Afr
37、ican National Standards are also available online from the SABS website http:/www.sabs.co.za Information on Standards The Standards Information Centre provides a wide range of standards-related information on both national and international standards, and is the official WTO/TBT enquiry point for So
38、uth Africa. The Centre also offers an individual updating service called INFOPLUS, which ensures that subscribers automatically receive notification regarding amendments to, and revisions of, international standards. Tel: +27 (0) 12 428 6666 Fax: +27 (0) 12 428 6928 E-mail: infosabs.co.za Copyright
39、The copyright in a South African National Standard or any other publication published by the SABS Standards Division vests in the SABS. Unless exemption has been granted, no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means without prior written permi
40、ssion from the SABS Standards Division. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any purpose other than implementation, prior written permission must be obtained. Details and advice can be obtained from the Senior Manager. Tel: +27 (0) 12 428 6666 Fax: +27 (0) 12 428 6928 E-mail: infosabs.co.za
