SIS 22 68 01-1966 Asbestos-cement corrugated sheets《石棉水泥波纹板》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

SANS 1700-3-7-2003 Fasteners Part 3 Forms dimensions and designations Section 7 Fasteners - Ends of parts with external ISO metric thread《紧固件 第3部分 形状、尺寸和命名 第7子部分 紧固件 带ISO公制外螺纹的部件的端.pdf

SANS 1700-3-8-1996 Fasteners Part 3 Forms dimensions and designations Section 8 Thread undercuts for external metric ISO threads《紧固件 第3部分：形式，尺寸和名称 第8部分：ISO米制外螺纹用螺纹退刀槽》.pdf

SANS 1700-3-9-1996 Fasteners Part 3 Forms dimensions and designations Section 9 Cross recesses for screws《紧固件 第3部分：形式，尺寸和名称 第9部分：螺钉的十字槽》.pdf

SANS 1700-4-1-2003 Fasteners Part 4 Tolerances Section 1 Tolerances for fasteners - Bolts screws studs and nuts - Product grades A B and C《紧固件 第4部分：公差第1节：紧固件公差 螺栓；螺钉；螺柱和螺母 产品等级A，B和.pdf

SANS 1700-4-3-2003 Fasteners Part 4 Tolerances Section 3 Tolerances for fasteners - Plain washers for bolts screws and nuts - Product grades A and C《紧固件 第4部分：公差第2节：紧固件公差 螺栓，螺钉和螺母用平.pdf

SANS 1700-5-10-2003 Fasteners Part 5 General requirements and mechanical properties Section 10 Mechanical properties of corrosion-resistant stainless-steel fasteners - Set screws a《紧.pdf

SANS 1700-5-11-2003 Fasteners Part 5 General requirements and mechanical properties Section 11 Electroplated coatings《紧固件 第5部分：一般要求和机械性能 第11节：电镀涂料》.pdf

SANS 1700-5-13-1996 Fasteners Part 5 General requirements and mechanical properties Section 13 Surface discontinuities - Bolts screws and studs for special requirements《紧固件 第5部分 一般.pdf

SANS 1700-5-15-2008 Fasteners Part 5 General requirements and mechanical properties Section 15 Bolts screws studs and nuts《紧固件 第5部分 一般要求和机械性能 第15子部分 表面间断性 对于螺栓、双头螺栓和螺母的特殊要求》.pdf