SNI 0546-2009 《自行车辐条》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

EN 2395-2005 en Aerospace series Aluminium alloy AL-P2014A-T4 or T42 Sheet and strip 0 4 mm Less Than or Equal to a Less Than or Equal to 6 mm《航空航天系列 AL-P2014A-T4或T42铝合金 薄板材和带材 0 4.pdf

EN 2398-2008 en Aerospace series - Heat resisting steel FE-PA2601 (X6NiCrTiMoV26-15) - Rm greater than or equal to 900 MPa - Bars for machined bolts - D less than or equal to 25 mm.pdf

EN 2399-2008 en Aerospace series - Heat resisting steel FE-PA2601 (X4NiCrTiMoV26-15) - Rm Greater than or equal to 900 MPa - Bars for forged bolts - D less than or equal to 25 mm《航.pdf

EN 24-1975 en Doors Measurement of Defects of General Flatness of Door Leaves《门 门扇总平直度缺陷测量》.pdf

EN 2402-2014 en Aerospace series - Heat resisting nickel base alloy NiCr20Co3Fe3 - Annealed - Wire - D 10 mm《航空航天系列 耐热镍基合金nicr20co3fe3 退火 Wire - D = 10 mm》.pdf

EN 2422-2005 en Aerospace series - Aluminium alloy AL-P2124-T351 - Plate - 25 mm greater than a greater than or equal to 120 mm《航空航天系列 铝合金AL-P2124-T351 板材 25 mm≤a≤120 mm》.pdf

EN 2424-2008 en Aerospace series - Marking of aerospace products《航空航天系列 航空标记》.pdf

EN 2430-1995 en Aerospace Series Ethylene-Propylene Rubber (EPM EPDM) Hardness 70 IRHD《航空和航天系列 乙丙橡胶(EPM EPDM) 硬度 70IRHD》.pdf

EN 2431-1995 en Aerospace Series Ethylene-Propylene Rubber (EPM EPDM) Hardness 80 IRHD《航空和航天系列 乙丙橡胶(EPM EPDM) 硬度 80IRHD》.pdf