1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 87B Standard for Power-Operated Dispensing Devices for Diesel Fuel, Biodiesel Fuel, Diesel/Biodiesel Blends with Nominal Biodiesel Concentrations up to 20 Percent (B20), Kerosene, and Fuel O
2、ilUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Power-Operated Dispensing Devices for Diesel Fuel, Biodies
3、el Fuel, Diesel/Biodiesel Blends with Nominal Biodiesel Concentrations up to 20 Percent (B20), Kerosene, and Fuel Oil, UL 87B First Edition, Dated February 13, 2015 Summary of Topics This rst edition of the Standard for Power-Operated Dispensing Devices for Diesel Fuel, Biodiesel Fuel, Diesel/Biodie
4、sel Blends with Nominal Biodiesel Concentrations up to 20 Percent (B20), Kerosene, and Fuel Oil, Ul 87B, apply to power-operated dispensing devices, rated 600 V ac or less, for use with fuels. The requirements are substantially in accordance with Proposal(s) on this subject dated October 17, 2014. A
5、ll rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form by any means, electronic, mechanical photocopying, recording, or otherwise without prior permission of UL. UL provides this Standard as is without warranty of any kind, either
6、expressed or implied, including but not limited to, the implied warranties of merchantability or tness for any purpose. In no event will UL be liable for any special, incidental, consequential, indirect or similar damages, including loss of prots, lost savings, loss of data, or any other damages ari
7、sing out of the use of or the inability to use this Standard, even if UL or an authorized UL representative has been advised of the possibility of such damage. In no event shall ULs liability for any damage ever exceed the price paid for this Standard, regardless of the form of the claim. Users of t
8、he electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold UL harmless from and against any loss, expense, liability, damage, claim, or judgment (including reasonable attorneys fees) resulting from any error or deviation introduced while purchaser is storing an electroni
9、c Standard on the purchasers computer system. The requirements in this Standard are now in effect, except for those paragraphs, sections, tables, gures, and/or other elements of the Standard having future effective dates as indicated in the note following the affected item. The prior text for requir
10、ements that have been revised and that have a future effective date are located after the Standard, and are preceded by a SUPERSEDED REQUIREMENTS notice. FEBRUARY 13, 2015 UL 87B tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL FEBRUARY 13
11、, 2015 UL 87B tr2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL February 13, 2015 1 UL 87B Power-Operated Dispensing Devices for Diesel Fuel, Biodiesel Fuel, Diesel/Biodiesel Blends with Nominal Biodiesel Concentrations
12、 up to 20 Percent (B20), Kerosene, and Fuel Oil Prior to the rst edition, the requirements for the products covered by this standard were included in the Outline of Investigation for Power-Operated Dispensing Devices for Diesel Fuel, Biodiesel Fuel, Diesel/Biodiesel Blends with Nominal Biodiesel Con
13、centrations up to 20 Percent (B20), Kerosene, and Fuel Oil, UL 87B. First Edition February 13, 2015 This ANSI/UL Standard for Safety consists of the First Edition. The most recent designation of ANSI/UL 87B as an American National Standard (ANSI) occurred on February 13, 2015. ANSI approval for a st
14、andard does not include the Cover Page, Transmittal Pages, Title Page, or effective date information. Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time. Proposals should be submitted via a Proposal Request in ULs On-Line Collaborative Standards Develo
15、pment System (CSDS) at http:/. ULs Standards for Safety are copyrighted by UL. Neither a printed nor electronic copy of a Standard should be altered in any way. All of ULs Standards and all copyrights, ownerships, and rights regarding those Standards shall remain the sole and exclusive property of U
16、L. COPYRIGHT 2015 UNDERWRITERS LABORATORIES INC. ANSI/UL 87B-2015UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL FEBRUARY 13, 2015 UL 87B 2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION W
17、ITHOUT PERMISSION FROM UL CONTENTS INTRODUCTION 1 Scope .5 2 General 6 2.1 Components .6 2.2 Units of measurement .6 2.3 Undated references .6 3 Glossary .6 CONSTRUCTION 4 General Construction 9 4.1 General .9 4.2 Hose assemblies .9 4.3 Strainers .10 4.4 Electrically operated valves .10 4.5 Hose noz
18、zle valve .10 4.6 Mechanically operated valves .10 5 Materials 11 5.1 Metallic materials 11 5.2 Nonmetallic materials 12 5.3 Materials - system level 15 5.4 Casting impregnation materials 15 5.5 Internal parts .15 6 Frame and Enclosure 15 6.1 Base .15 6.2 Pedestal .16 6.3 Housing 16 7 Vapor Barrier
19、.18 8 AirGap.20 9 Pumping Units .21 10 Pressure Relief .21 11 Springs 22 12 Strainers .22 13 Valves .23 13.1 Electrically operated valves 23 13.2 Hose nozzle valves .23 13.3 Shear valves 23 13.4 Mechanically operated valves 23 14 Mechanical Line Leak Detectors 23 15 Piping and Fittings 24 16 Hose As
20、semblies .25 17 Control System .25 18 Meter 26 19 Breakaway Couplings and Swivel Connectors 26 ELECTRICAL EQUIPMENT 20 General 26 21 Motors .29 FEBRUARY 13, 2015 UL 87B 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 22 Switches .29 23 Clas
21、s I, Group D, Division 2 Location, Lighting, Electrical, and Electronic Equipment 29 24 Wiring Methods .30 25 Locking Mechanism .33 PERFORMANCE 26 General 33 27 Test Sequences 34 27.1 General .34 27.2 General dispenser test sequence 34 28 Long Term Exposure Test .34 28.1 General .34 28.2 Samples 34
22、28.3 Method .35 28.4 Results .36 29 High Pressure Leakage Test .36 30 Hydrostatic Strength Test 37 31 Start-To-Discharge Test .37 32 Dimensional Stability of Floats 38 33 Weight Change of Floats 38 34 Endurance Test Hose Retrieving Mechanism .39 35 Endurance Test Hose Fastening Means .40 36 Marking
23、Adhesion Test 40 37 Torque Test 40 38 Rain Test 41 39 Temperature Reduction Test .44 40 Leakage of Wire Seal Test .44 41 Tests on Sealing Compounds 44 42 10 Day Moist Ammonia-Air Stress Cracking Test .45 MARKING 43 General 46 43.1 Details 46 43.2 Cautionary markings 47 INSTRUCTION MANUALS 44 General
24、 47 45 Instructions Pertaining to Risk of Fire, Electric Shock, or Injury to Persons .48 46 Installation Instructions 49 47 Operating Instructions .49 48 Maintenance Instructions 50 SUPPLEMENT SA - Test Fluids SA.1 Representative aggressive combustible test fuel mixtures SA1 FEBRUARY 13, 2015 UL 87B
25、 4UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL INTRODUCTION 1 Scope 1.1 These requirements apply to power-operated dispensing devices, rated 600 V ac or less, for use with fuels. Fuels, as dened by these requirements, include one or more
26、of the fuels described in 1.2. 1.2 Dispensing devices covered by these requirements are intended for use with one or more of the following: a) Diesel fuel and diesel fuel/biodiesel blends with nominal biodiesel concentrations up to 5 percent (B0 B5) formulated in accordance with the Standard Specica
27、tion for Diesel Fuel Oils, ASTM D975. b) Diesel/biodiesel blends with nominal biodiesel concentrations from 5 percent up to 20 percent (B6 B20) formulated in accordance with the Standard Specication for Diesel Fuel Oil, Biodiesel Blends (B6 B20), ASTM D7467. c) Biodiesel (B99.9/B100) formulated in a
28、ccordance with the Standard Specication for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels, ASTM D6751. d) Kerosene formulated in accordance with the Standard Specication for Kerosine, ANSI/ ASTM D3699. e) Fuel Oil (heating oil) formulated in accordance with the Standard Specication f
29、or Fuel Oils, ASTM D396. 1.3 Requirements for the installation and use of dispensing devices are included in the Code for Motor Fuel Dispensing Facilities and Repair Garages, ANSI/NFPA 30A, and the National Electrical Code, ANSI/NFPA 70. 1.4 These requirements apply to wiring methods used to install
30、 or interconnect such control equipment when the equipment is located directly on or within the housing of the dispensing device. 1.5 These requirements do not apply to control equipment that may authorize, monitor, or interrupt operation of a power-operated dispensing device, nor other auxiliary eq
31、uipment. These products would be covered under the Standard for Control Equipment for Use with Flammable Liquid Dispensing Devices, UL 1238. 1.6 These requirements do not cover dispensing devices for use with gasoline or gasoline/ethanol blends of any concentration. These dispensing devices are cove
32、red under the Standard for Power-Operated Dispensing Devices for Gasoline and Gasoline/Ethanol Blends with Nominal Ethanol Concentrations up to 85 Percent (E0 E85), UL 87A. 1.7 These requirements do not cover dispensing devices for use with LP-Gas, which are covered under the Standard for Power-Oper
33、ated Dispensing Devices for LP-Gas, UL 495. FEBRUARY 13, 2015 UL 87B 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 1.8 These requirements do not cover equipment intended for diesel/biodiesel blends with a biodiesel concentration between B
34、20 and B99.9/B100. 2 General 2.1 Components 2.1.1 Except as indicated in 2.1.2, a component of a product covered by this standard shall comply with the requirements for that component. 2.1.2 A component is not required to comply with a specic requirement that: a) Involves a feature or characteristic
35、 not required in the application of the component in the product covered by this standard, or b) Is superseded by a requirement in this standard. 2.1.3 A component shall be used in accordance with its rating established for the intended conditions of use. 2.1.4 Specic components are incomplete in co
36、nstruction features or restricted in performance capabilities. Such components are intended for use only under limited conditions, such as certain temperatures not exceeding specied limits, and shall be used only under those specic conditions. 2.2 Units of measurement 2.2.1 Values stated without par
37、entheses are the requirement. Values in parentheses are explanatory or approximate information. 2.3 Undated references 2.3.1 Any undated reference to a code or standard appearing in the requirements of this standard shall be interpreted as referring to the latest edition of that code or standard. 3
38、Glossary 3.1 For the purpose of this standard, the following denitions apply. 3.2 AIR GAP A minimum of 1 inch (25.4 mm) free air space provided between the planes of Division 1 and Division 2 hazardous locations and an unclassied area of a dispensing device. 3.3 BASE The part of the assembly that is
39、 intended to be secured to the foundation on which the device will be installed. 3.4 CLASS I HAZARDOUS LOCATIONS Locations in which ammable gases or vapors are or may be present in the air in quantities sufficient to produce explosive or ignitable mixtures. For the purpose of these requirements, as
40、applied to dispensing systems of other than the overhead type, the following classied areas are further dened. The area of the dispensing system covered by these requirements is the envelope dened by the maximum outer dimensions. a) Class I, Group D, Division 1 FEBRUARY 13, 2015 UL 87B 6UL COPYRIGHT
41、ED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 1) The area within a dispenser housing up to 4 feet (1.2 m) vertically above the base, except for that area dened as Division 2 or unclassied. 2) Any area within a nozzle boot. b) Class I, Group D, Divisio
42、n 2 1) Areas within a dispenser housing above the Division 1 area. 2) The area surrounding the dispenser housing within 18 inches (46 cm) horizontally in all directions from the Division 1 area located within the housing. 3) The area within 18 inches horizontally, in all directions from the opening
43、of a nozzle boot not isolated by a vapor tight partition, except that the area is not required to be extended around a 90 degree or greater corner. 3.5 DISPENSER, REMOTE CONTROL TYPE A dispensing device that does not contain a power- operated pump as part of the assembly, and which is intended for c
44、onnection to a uid piping system containing the power-operated pumps at a remote location. Also commonly identied as a “dispenser”. 3.6 DISPENSER, SELF-CONTAINED A dispensing device that includes a power-operated pump as part of the assembly. Also commonly identied as a “pump” or “suction dispenser”
45、. 3.7 DISPENSING DEVICE A product consisting of various components as applicable, which are used to control and meter the ow of liquid from an upstream storage device. 3.8 ELECTRICAL CIRCUITS a) High Voltage Circuit A circuit having a potential of not more than 600 volts and having circuit character
46、istics in excess of those of a low voltage or Class 2 circuit. b) Low Voltage Circuit A circuit involving a potential of not more than 30 volts ac (rms) (42.4 volts peak or dc) and 1) Supplied by a Class 2 transformer, or by a battery, by a battery and xed impedance, or by a transformer and xed impe
47、dance each of which, as a unit, is in compliance with what is required for a Class 2 transformer, or 2) Limited to a maximum of 100 volt-amperes. A circuit derived from a source of supply classied as a high voltage circuit, by connecting resistance in series with the supply circuit as a means of lim
48、iting the voltage and current, is not considered to be a low voltage circuit. c) Intrinsically Safe Circuit A circuit incapable of releasing sufficient electrical energy under normal or abnormal conditions to cause ignition of a specic hazardous atmospheric mixture. Abnormal conditions include unint
49、entional damage to any part of the equipment or wiring, insulation or other malfunction of electrical components, application of overvoltage, adjustment and maintenance operations, and other similar conditions. 3.9 DIESEL/BIODIESEL BLENDS Blended fuels composed of a diesel component and a biodiesel component. The numerical value corresponding to the biodiesel component determines the blend rating (such as B20 for 20% biodiesel, 80% diesel). FEBRUARY 13, 2015 UL 87B 7UL COPY
