1、raising standards worldwide NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BSI Standards Publication BS ISO 7207-2:2011 Implants for surgery Components for partial and total knee joint prostheses Part 2: Articulating surfaces made of metal, ceramic and plastics materialsBS IS
2、O 7207-2:2011 BRITISH STANDARD National foreword This British Standard is the UK implementation of ISO 7207-2:2011. It supersedes BS7251-14:1998 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee CH/150/4, Surgical Implants - Bone and Joint Replacements.
3、 A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. BSI 2011 ISBN 978 0 580 66597 4 ICS 11.040.40 Compliance wit
4、h a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 July 2011. Amendments issued since publication Date Text affectedBS ISO 7207-2:2011Reference number ISO 7207-2:2011(E) ISO
5、2011INTERNATIONAL STANDARD ISO 7207-2 Second edition 2011-07-01 Implants for surgery Components for partial and total knee joint prostheses Part 2: Articulating surfaces made of metal, ceramic and plastics materials Implants chirurgicaux lments de prothses partielle et totale de larticulation du gen
6、ou Partie 2: Surfaces articulaires constitues de matriaux mtalliques, cramiques et plastiques BS ISO 7207-2:2011 ISO 7207-2:2011(E) COPYRIGHT PROTECTED DOCUMENT ISO 2011 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any m
7、eans, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail cop
8、yrightiso.org Web www.iso.org Published in Switzerland ii ISO 2011 All rights reservedBS ISO 7207-2:2011 ISO 7207-2:2011(E) ISO 2011 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). Th
9、e work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-gov
10、ernmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
11、The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vo
12、te. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 7207-2 was prepared by Technical Committee ISO/TC 150, Implants for surgery, Subcommittee SC
13、4, Bone and joint replacements. This second edition cancels and replaces the first edition (ISO 7207-2:1998), which has been technically revised. ISO 7207 consists of the following parts, under the general title Implants for surgery Components for partial and total knee joint prostheses: Part 1: Cla
14、ssification, definitions and designation of dimensions Part 2: Articulating surfaces made of metal, ceramic and plastics materials BS ISO 7207-2:2011BS ISO 7207-2:2011 INTERNATIONAL STANDARD ISO 7207-2:2011(E) ISO 2011 All rights reserved 1Implants for surgery Components for partial and total knee j
15、oint prostheses Part 2: Articulating surfaces made of metal, ceramic and plastics materials 1 Scope This part of ISO 7207 specifies surface finish requirements for the articulating surfaces of total and partial knee joint prostheses classified in ISO 7207-1. This part of ISO 7207 is intended to prov
16、ide guidance for periodic validation of production processes. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document
17、(including any amendments) applies. ISO 4287, Geometrical Product Specifications (GPS) Surface texture: Profile method Terms, definitions and surface texture parameters ISO 4288:1996, Geometrical Product Specifications (GPS) Surface texture: Profile method Rules and procedures for the assessment of
18、surface texture 3 Surface finish requirements 3.1 General All surface finish measurements shall be performed according to the max.-rule in ISO 4288:1996, 5.3. The max.-rule states that no measurement values shall exceed the specified Ramax. 3.2 Knee joint prostheses 3.2.1 Metallic or ceramic femoral
19、 components When measured in accordance with ISO 4287, all articulating surfaces of a metallic or ceramic femoral component shall be measured across the full articulating surface at locations in an approximately square grid of locations no more than 10 mm apart. The component shall have an Ramax val
20、ue 0,1 m, using a cut-off value of 0,08 mm. NOTE The patellar flange is considered an articulating surface in bicompartmental, tricompartmental and patellar femoral replacement systems. BS ISO 7207-2:2011 ISO 7207-2:2011(E) 2 ISO 2011 All rights reservedThe following details should be reported along
21、 with the surface roughness, Ra, values: a) stylus tip radius; b) position of measurements on the specimen. When examined with normal or corrected vision, the articulating surface shall be free from embedded particles, defects and raised edges and from scratches and score marks. 3.2.2 Metallic or ce
22、ramic tibial articulating components of a mobile bearing knee When measured in accordance with ISO 4287, all articulating surfaces of a metallic or ceramic tibial component shall be measured across the full articulating surface at locations in an approximately square grid of locations no more than 1
23、0 mm apart. The component shall have an Ramax value 0,1 m, using a cut-off value of 0,08 mm. The following details should be reported along with the surface roughness, Ra, values: a) stylus tip radius; b) position of the measurements on the specimen. When examined with normal or corrected vision, th
24、e articulating surface shall be free from embedded particles, defects and raised edges and from scratches and score marks. 3.2.3 Plastics tibial and patella components When measured in accordance with ISO 4287, all articulating surfaces of a tibial and patella component shall be measured across the
25、full articulating surface at locations in an approximately square grid of locations no more than 10 mm apart. The component shall have an Ramax value 2 m, using a cut-off value of 0,08 mm. The following details should be reported along with the measured surface roughness, Ra, values: a) stylus tip r
26、adius; b) position of the measurements on the specimen. When examined with normal or corrected vision, the articulating surface shall be free from embedded particles, defects and raised edges and from scratches and score marks other than those arising from the finishing process. BS ISO 7207-2:2011 I
27、SO 7207-2:2011(E) ISO 2011 All rights reserved 3Bibliography 1 ISO 7207-1, Implants for surgery Components for partial and total knee joint prostheses Part 1: Classification, definitions and designation of dimensions BS ISO 7207-2:2011 ISO 7207-2:2011(E) ICS 11.040.40 Price based on 3 pages ISO 2011
28、 All rights reserved This page deliberately left blankBSI is the independent national body responsible for preparing British Standards and other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. It is incorporated
29、 by Royal Charter. British Standards Institution (BSI) raising standards worldwide BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK Tel +44 (0)20 8996 9001 Fax +44 (0)20 8996 7001 British Standards are updated by amendment or revision. Users of British Stan- dards should make sure tha
30、t they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and serv- ices. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical com- mittee responsib
31、le, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001 BSI offers Members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Tel: +44 (0)20 8996 7669 Fax: +44 (
32、0)20 8996 7001 Email: Buying standards You may buy PDF and hard copy versions of standards directly using a credit card from the BSI Shop on the website In addition all orders for BSI, international and foreign standards publications can be addressed to BSI Customer Services. Tel: +44 (0)20 8996 9
33、001 Fax: +44 (0)20 8996 7001 Email: In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national,
34、 European and international standards through its Knowledge Centre. Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005 Email: Various BSI electronic information services are also available which give details on all its products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email:
35、BSI Subscribing Members are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Ad- ministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding o
36、nline access to British Standards via British Standards Online can be found at Further information about BSI is available on the BSI website at www.bsi- Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardi
37、zation bodies. Ex- cept as permitted under the Copyright, Designs and Patents Act 1988 no ex- tract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not pre
38、clude the free use, in the course of implementing the standard of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copy- right & Licensing Manager. Tel: +44 (0)20 8996 7070 Email:
