1、raising standards worldwide NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BSI Standards Publication BS ISO/IEC 21117:2012 Incorporating corrigendum September 2012 Information technology Office equipment Copying machines and multi-function devices Information to be included i
2、n specification sheets and related test methodsBS ISO/IEC 21117:2012 BRITISH STANDARD National foreword This British Standard is the UK implementation of ISO/IEC 21117:2012. The UK participation in its preparation was entrusted to Technical Committee IST/3, IT Printers and Cartridges. A list of orga
3、nizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2012. Published by BSI Standards Limited
4、2012 ISBN 978 0 580 80539 4 ICS 37.100.10 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 August 2012. Amendments issued since publication Date Text affected
5、 30 September 2012 Title correctionBS ISO/IEC 21117:2012Reference number ISO/IEC 21117:2012(E) ISO/IEC 2012INTERNATIONAL STANDARD ISO/IEC 21117 Second edition 2012-06-15Information technology Office equipment Copying machines and multi-function devices Information to be included in specification she
6、ets and related test methods Technologies de linformation Machines de bureau Machines copiantes et dispositifs multifonctionnels Information inclure dans les feuilles de spcifications et les mthodes relatives dessai BS ISO/IEC 21117:2012 ISO/IEC 21117:2012(E) COPYRIGHT PROTECTED DOCUMENT ISO/IEC 201
7、2 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the coun
8、try of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO/IEC 2012 All rights reservedBS ISO/IEC 21117:2012 ISO/IEC 21117:2012(E) ISO/IEC 2012 All rights reserved i
9、iiContents Page Foreword iv 1 Scope 1 2 Normative references 1 3 Information to be included in specification sheets . 1 4 Specification sheets 2 4.1 Main unit . 2 4.2 Option devices . 2 4.3 Extended functions . 2 5 Test and measurement methods . 2 5.1 Test and measurement conditions 2 5.2 Test and m
10、easurement methods . 2 Annex A (informative) Specification sheets for copying machines and multi-function devices (main units) 21 Annex B (informative) Specification sheets for document feeders . 23 Annex C (informative) Specification sheets for auxiliary paper-supply devices . 24 Annex D (informati
11、ve) Specification sheets for sorters 25 Annex E (informative) Specification sheets for finishers . 26 Annex F (informative) Specification sheets for scanner functions . 27 Annex G (informative) Specification sheets for printer functions . 28 Annex H (informative) Specification sheets for facsimile f
12、unctions . 29 Annex I (informative) Specification sheets for Internet facsimile functions (including e-mail transmission functions) 30 Bibliography 31 BS ISO/IEC 21117:2012 ISO/IEC 21117:2012(E) iv ISO/IEC 2012 All rights reservedForeword ISO (the International Organization for Standardization) and
13、IEC (the International Electrotechnical Commission) form the specialized system for worldwide standardization. National bodies that are members of ISO or IEC participate in the development of International Standards through technical committees established by the respective organization to deal with
14、 particular fields of technical activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other international organizations, governmental and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information technology, ISO and IEC have
15、 established a joint technical committee, ISO/IEC JTC 1. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of the joint technical committee is to prepare International Standards. Draft International Standards adopted by the joint
16、technical committee are circulated to national bodies for voting. Publication as an International Standard requires approval by at least 75 % of the national bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. I
17、SO and IEC shall not be held responsible for identifying any or all such patent rights. ISO/IEC 21117 was prepared by Joint Technical Committee ISO/IEC JTC 1, Information technology, Subcommittee SC 28, Office equipment. This second edition cancels and replaces the first edition (ISO/IEC 21117:2005)
18、, which has been technically revised. BS ISO/IEC 21117:2012 INTERNATIONAL STANDARD ISO/IEC 21117:2012(E) ISO/IEC 2012 All rights reserved 1Information technology Office equipment Copying machines and multi-function devices Information to be included in specification sheets and related test methods 1
19、 Scope This International Standard specifies the information to be listed in specification sheets for electrophotographic digital copying machines and multi-function devices. The intention of this International Standard is to allow purchasers and users to compare the characteristics of different mod
20、els of copying machines and multi- function devices so that they can more easily select copying machines and multi-function devices that meet their requirements. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, on
21、ly the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 7779:2010, Acoustics Measurement of airborne noise emitted by information technology and telecommunications equipment ISO 9296:1988, Acoustics Declared noise em
22、ission values of computer and business equipment ISO/IEC 24734, Information technology Office equipment Method for measuring digital printing productivity ISO/IEC 24735, Information technology Office equipment Method for measuring digital copying productivity ISO/IEC 29183, Information technology Of
23、fice equipment Method for measuring digital copying productivity of a single one-sided original 3 Information to be included in specification sheets Table 1 defines a name and a short description for each parameter entry. These constitute the information to be included in specification sheets. Furth
24、ermore, test and measurement methods are defined for parameters where applicable in the “Definitions and methods of measurement” column. Specification sheets shall use the parameter names listed in Table 1. Specification sheets must include all applicable parameters in the given order. Parameters th
25、at do not function, however, may be omitted. NOTE When extracting parameters and specification values from specification sheets for use in catalogs, there are no particular provisions on the parameter numbers or on the order in which the parameters are listed. BS ISO/IEC 21117:2012 ISO/IEC 21117:201
26、2(E) 2 ISO/IEC 2012 All rights reserved4 Specification sheets 4.1 Main unit Refer to Annex A. 4.2 Option devices a) document feeder: refer to Annex B. b) auxiliary paper-supply devices: refer to Annex C. c) sorters: refer to Annex D. d) finishers: refer to Annex E. 4.3 Extended functions a) scanner
27、function: refer to Annex F. b) printer function: refer to Annex G. c) facsimile function: refer to Annex H. d) e-mail / internet facsimile function: refer to Annex I. 5 Test and measurement methods 5.1 Test and measurement conditions The test environment, including temperature and humidity, shall be
28、 within the ranges recommended by the manufacturer for operating the device. If no recommendation is available, the following ranges shall apply. Temperature: 23 C 5 C Relative humidity: (50 20) % Supply voltage: rated input voltage Supply frequency: rated frequency Paper size: A4 Paper weight: 60 g
29、/m2 to 90 g/m2 If a different paper size other than A4 is used, the size should be stated in the specification sheets. The paper used in the tests should be conditioned under the environmental conditions given above. 5.2 Test and measurement methods Test and measurement method for each parameter is
30、specified in Table 1. BS ISO/IEC 21117:2012 ISO/IEC 21117:2012(E) ISO/IEC 2012 All rights reserved 3Table 1 Parameters to be included in specification sheets Parameter Description of the entry Remarks and examples Definitions and methods of measurement 1 Main unit Refer to Annex A. 1.1 Name Product
31、name and model number. 1.2 Type States if the machine is a portable, desktop, or floor-standing (console) type and if the machine is an all-in- one or multi-component type. 1.3 Copying method Analog or digital 1.4 Colour States if single-colour or full-colour copying is supported for machines that s
32、upport colour copying. 1.5 Type of photoreceptor Organic material, a-Si or Selenium. 1.6 Scanning light source States the type of light source used for scanning and its rated power consumption in watts. 1.7 Type of platen Moving or stationary. If no platen is provided and the original is fed into th
33、e machine by hand or with a document carrier, indicate the platen as “feed-through”. 1.8 Scanning method States the method by which originals are scanned and the type of scanning device. 1.9 Writing method States the method by which the latent image is written to the photoreceptor. 1.10 Developing m
34、ethod Mono or dual components. 1.11 Copy density adjustment Manual or automatic. If manual, indicate the adjustment method, such as continuous or discrete. 1.12 Fixing method Heat-roller, flash, oven, or pressure fixing. 1.13 Paper-supply device/paper- supply capacity States the paper-supply method
35、(automatic or manual) and the number of cassettes, decks, and trays (attached to the main unit). Also, indicate the loading capacity in sheets for each cassette, deck, and tray for a defined paper weight (in g/m2). If there are multiple pickup trays, indicate the loading capacity for each pickup tra
36、y. For machines that use roll sheets, list the width and length of roll sheets. BS ISO/IEC 21117:2012 ISO/IEC 21117:2012(E) 4 ISO/IEC 2012 All rights reservedTable 1 (continued) Parameter Description of the entry Remarks and examples Definitions and methods of measurement 1.14 Scanning resolution St
37、ates the main and sub scanning resolutions as needed, expressed in “dpi” or “dpi (number of dots/25.4 mm)”. Example: Optical resolution:1,200 x 1200 dpi 1.15 Writing resolution States the main and sub write resolution, expressed in “dpi” or “dpi (number of dots / 25.4 mm)”. Writing resolution equals
38、 to the print engines native addressability. Example: 1,200 x 1200 dpi 1.16 Scan colours The tones may be specified if they vary when the machine operates in copying mode. Example: 24-bit colour (8-bits per colour plane) 1.17 Acceptable originals Lists sheets, books, computer forms, and other accept
39、able originals. 1.18 Copy paper Indicates any specially processed copy paper that is used. Also, states the paper weight that can be transported in the machine. The recommended unit is g/m2. 1.19 Original sizes States the maximum size in millimeters. The specification sheet should indicate any limit
40、ations on the thickness of originals as well as the maximum weight that can be placed on the platen. 1.20 Copying dimensions States the maximum and minimum dimensions that can be copied in millimeters. If the copying size varies by the paper-supply method (manual or automatic), this is indicated. 1.
41、21 Non-image area Non-image area is the area that cannot be copied on when copying an original without margins on a given paper size. States in millimeters the width of the non-copy area at the top, bottom, and side of the page. The non-image areas at each edge shall be indicated. The non-image area
42、s shall be measured from the top, bottom, and sides of the copy paper to the image, copied under normal usage conditions. BS ISO/IEC 21117:2012 ISO/IEC 21117:2012(E) ISO/IEC 2012 All rights reserved 5Table 1 (continued) Parameter Description of the entry Remarks and examples Definitions and methods
43、of measurement 1.22 Possible enlargement and reduction Indicates the possible enlargement and reduction expressed as a normalized ratio to the length of the original. The ratio is stated for enlarged copies, reduced copies, and direct (1:1) copies to two decimal places. Express the error deviation o
44、f direct (1:1) copying as a percent. The deviation percentage (%) shall be the maximum deviation, including variations between machines of the same model. 1.23 Number of continuous copies Indicates in pages the maximum number of copies that can be set for continuous copying when the machine operates
45、 as a copying machine. 1.24 Continuous copying speed States the number in pages/minute that can be made under normal usage conditions (A4 paper, 1:1 magnification, and standard feed direction) in continuous copying mode. Specify if copying speeds vary by paper size. For colour copying machines, spec
46、ify the copying speeds for both colour copying and monochrome (black and white) copying. Specify if copying speeds vary by copying process. Each respective copying speed should be indicated. The number of copies is expressed in Copies Per Minute (CPM) in the following formats. a) Less than 10 CPM: R
47、ound off to two decimal places and express as two significant figures: X.X b) 10 CPM to 99 CPM: Express with either of the methods below: 1) Round off to one decimal place and express as two significant figures: XX 2) Round off to two decimal places and express as three significant figures: XX.X c)
48、100 CPM or more: Round off to one decimal place and express as three significant figures: XXX ISO/IEC 24735 shall be used to describe the copying productivity of copier and MFP devices. (See parameter 1.42 Copying Productivity) The machine shall be set to copy 11 copies under normal usage conditions
49、 (A4 paper, 1:1 magnification, and standard feed direction). Measure the time (that is, obtain the value t in seconds) from when the first copy is fully ejected to when the 11th copy is fully ejected. This value shall be converted into the number of copies per minute with the following equation: 60 (t/10) = the number of copies per minute For continuous passed pages, a number of pages equivalent to the number of copies per minute + 1 may be passed. In this case, “10” in the equation above
