1、ASD STANDARD NORME ASD ASD NORM prEN 3155-015 Edition P 4 October 2005 PUBLISHED BY THE AEROSPACE AND DEFENSE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATION Gulledelle 94 - B-1200 Brussels - Tel. + 32 2 775 8126 - Fax. + 32 2 775 8111 - www.asd-stan.orgICS: 49.060 Supersedes edition P 3 February
2、 2000 Descriptors: ENGLISH VERSION Aerospace series Electrical contacts used in elements of connection Part 015: Contacts, electrical, female, type A, crimp, class S Product standard Srie arospatiale Contacts lectriques utiliss dans les organes de connexion Partie 015 : Contacts lectriques, femelles
3、, type A, sertir, classe S Norme de produit Luft- und Raumfahrt Elektrische Kontakte zur Verwendung in Verbindungselementen Teil 015: Elektrische Buchsenkontakte, Typ A, crimpbar, Klasse S Product Norm This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The Eu
4、ropean Association of Aerospace Industries - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this pre-standard, the technical conten
5、t shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement of ASD-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee
6、for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. Edition approved for
7、publication 31 October 2005 Comments should be sent within six months after the date of publication to ASD-STAN Electrical Domain Copyright 2005 by ASD-STAN prEN 3155-015:20052 Foreword This standard was reviewed by the Domain Technical Coordinator of ASD-STANs Electrical Domain. After inquiries and
8、 votes carried out in accordance with the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication. Contents Page Introduction .3 1 Scope 3 2 Normative references 3 3 Terms and definitions .4 4 Required characteristics.4 4.1 Specific characte
9、ristics.4 4.2 Dimensions and mass.4 4.3 Marking by colour code 6 4.4 Material and surface treatment.7 4.5 Permissible cables 7 4.6 Tooling 8 4.6.1 Crimping tools8 4.6.2 Insertion/Extraction tools .8 4.7 Cable stripping.9 4.8 Tests9 4.9 Gauges. 10 5 Designation . 11 6 Marking 11 7 Technical specifica
10、tion 11 prEN 3155-015:20053 Introduction The contacts defined by this standard are derived from those of SAE-AS-39029/63 and, intermateable with those of SAE-AS-39029/64. They are specified as a 200 C class instead of 125 C class as detailed in the MIL standard. 1 Scope This standard specifies the r
11、equired characteristics, tests and tooling applicable to female electrical contacts 015, type A, crimp, class S, used in elements of connection according to EN 3155-002. It shall be used together with EN 3155-001. The associated male contacts are defined in EN 3155-014. 2 Normative references The fo
12、llowing referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 8843, Aircraft Crimp-removable contacts for electri
13、cal connectors Identification system. EN 2083, Aerospace series Copper or copper alloy conductors for electrical cables Product standard. EN 2591-*, Aerospace series Elements of electrical and optical connection Test methods. EN 3155-001, Aerospace series Electrical contacts used in elements of conn
14、ection Part 001: Technical specification. 1)EN 3155-002, Aerospace series Electrical contacts used in elements of connection Part 002: List and utilization of contacts. 1)EN 3155-014, Aerospace series Electrical contacts used in elements of connection Part 014: Contacts, electrical, male, type A, cr
15、imp, class S Product standard. 1)EN 4008-006, Aerospace series Elements of electrical and optical connection Crimping tools and associated accessories Part 006: Positioner for crimping tool M22520/7 Product standard.1)MIL-DTL-22520, Crimping tools, terminal, hand or power actuated, wire termination,
16、 and tool kits general specification for. 2)MIL-C-22520/1, Crimping tools, terminal, hand, wire termination for wire barrel sizes 12 through 20. 2)MIL-C-22520/2, Crimping tools, terminal, hand, wire termination for wire barrel sizes 20 through 28. 2)* All its parts quoted in Table 7. 1) Published as
17、 AECMA Prestandard at the date of publication of this standard. 2) Published by: Department of Defense (DOD), the Pentagon, Washington D.C. 20301 USA. prEN 3155-015:20054 MIL-C-22520/7, Crimping tools, terminal, hand, wire termination for wire barrel sizes 16, 20 and 22. 2) MIL-I-81969, Installing a
18、nd removal tools, connector electrical contact, general specification for. 2)MIL-I-81969/1, Installing and removal tools, connector electrical contact, type III, class 2, composition C. 2)MIL-I-81969/30, Installing and removal tools, connector electrical contact, type II, class 2, composition C for
19、unwired contacts. 2)MIL-I-81969/39, Installing and removal tools, connector electrical contact, type III, class 2, composition B. 2)SAE-AS-39029, Contacts, electrical connector, general specification for. 3)SAE-AS-39029/63, Contacts, electrical connector, socket, crimp removable, (for MIL-C-24308 co
20、nnectors). 3)SAE-AS-39029/64, Contacts, electrical connector, pin, crimp removable, (for MIL-C-24308 connectors). 3)3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 3155-001 apply. 4 Required characteristics 4.1 Specific characteristics Type A contacts
21、 are for general application and class S corresponds to an operating temperature range from 65 C to 200 C. 4.2 Dimensions and mass See Figures 1, 2 and 3 and Table 1. Dimensions and tolerances are given in millimetres and apply after surface treatment. 3) Published by: Society of Automotive Engineer
22、ing (SAE), 400 Commonwealth Drive, Warrendale, PA 15096, USA. prEN 3155-015:20055 1 2M 0,25 max. 1,04 max.5 4 3 010 Diameter general concentricity 0,025 C and D Key 1 Colour bands, see Table 2. 2 E (one side only). 3 This dimension represents both the length of the bore A which includes the active z
23、one of protection (see EN 3155-001, 5.3.2). 4 Clearance between sleeve and body of the contact 5 Point at which a square ended gauge pin of the same basic diameter as the mating contact first engages the female contact spring member. Figure 1 Figure 2 Barrel 20-20 prEN 3155-015:20056 C1 Key 1 14 to
24、16 Figure 3 Barrel 20-22 Table 1 Size A B C D E F G H J M Contact Barrel min. Massg max.20 22 1,14 1,07 2,16 2,08 1,80 1,73 0,90 0,85 0,85 0,60 1,85 1,75 4,70 3,60 1,40 1,24 0,15 0,10 7,00 0,17 20 20 1,14 1,07 2,16 2,08 1,80 1,73 1,17 1,09 0,85 0,60 1,85 1,75 4,70 3,60 1,40 1,24 0,15 0,10 7,00 0,17
25、20 18 1,14 1,07 2,16 2,08 1,80 1,73 1,35 1,30 0,85 0,60 1,85 1,75 4,70 3,60 1,40 1,24 0,15 0,10 7,00 0,17 4.3 Marking by colour code See Table 2. prEN 3155-015:20057 Table 2 Size Two bands according to ISO 8843Three bands according to SAE-AS-39029/63 aContact Barrel cBand 1 dBand 2 cBand 1 dBand 2 e
26、Band 3 20 22 Red Green 20 20 Red Red Orange Blue Grey 20 18 Red Brown b aContacts supplied with three colour bands must conform to this EN standard. bViolet colour band not to be used for new manufacture. 4.4 Material and surface treatment Body material: copper alloy Surface treatment: gold on an ap
27、propriate undercoat, selective protection permitted, thickness of protection not specified. 4.5 Permissible cables See Table 3. Table 3 Size Size of conductors Contact Barrel AECMA CodeSection mm2AWG aRated test current A 20 22 004 002 001 0,40 0,25 0,15 22 24 26 5,0 3,0 2,0 20 20 006 004 002 0,60 0
28、,40 0,25 20 22 24 7,5 5,0 3,0 20 18 010 006 004 002 1,00 0,60 0,40 0,25 18 20 22 24 7,5 7,5 5,0 3,0 aAWG = Closest American Wire Gauge. prEN 3155-015:20058 4.6 Tooling 4.6.1 Crimping tools Conform to MIL-DTL-22520. See Table 4. The selector qualification numbers used for crimping copper and copper a
29、lloy conductors in electrical cables EN 2083 are indicated in Table 4. It is the responsibility of the user if the parameters in Table 4 are changed for service use. Table 4 Contact Cable size Tools M22520/1-01 Tools M22520/2-01 Tools M22520/7-01 Contact size Barrel size AECMA code AWGa Positioner S
30、elector numberPositioner Selector numberPositioner Selector number001 26 2 1 002 24 3 2 004 22 4 3 20 22 Not applicable M22520/2-08 EN4008-006 002 24 5 4 004 22 6 5 006 20 7 6 20 20 Not applicable M22520/2-08 EN4008-006 002 24 5 4 004 22 6 5 006 20 7 6 20 18 010 18 Not applicable M22520/2-087 EN4008
31、-006 6 aAWG = Closest American Wire Gauge. 4.6.2 Insertion/Extraction tools Conform to MIL-I-81969. See Table 5. Table 5 Size Extraction tools Contact Barrel Insertion tools Wired contact Unwired contact 20 22 M81969/39-01 M81969/1-02 M81969/39-01 M81969/1-02 M81969/30-11 20 20 M81969/39-01 M81969/1
32、-02 M81969/39-01 M81969/1-02 M81969/30-11 20 18 M81969/39-01 M81969/1-02 M81969/39-01 M81969/1-02 M81969/30-11 prEN 3155-015:20059 4.7 Cable stripping See Table 6. Table 6 Size Contact Barrel Stripped length of cable mm 0,5 20 22 4 20 20 5 20 18 5 4.8 Tests See Table 7. Table 7 Applicable EN 2591- T
33、est Not applicableAccording to EN 3155-001 Remarks 101 Visual examination X 102 Examination of dimensions and mass X 201 Contact resistance low level X 202 Contact resistance at rated current X 204 Discontinuity of contacts in the microsecond range X 210 Electrical overload X 220 Contact/conductor j
34、oint ageing by current and temperature cycling X 301 Endurance at temperature X T = (200 2) C Duration: 1 000 h 305 Rapid change of temperature X TA= (200 2) C TB= ( 65 2) C 307 Salt mist X 315 Fluid resistance X 319 Gastightness of solderless wrapped connections X 402 Shock X Method B: severity 50
35、403 Sinusoidal and random vibration X Method A, Figure 1, 20 g (level 2) Duration: 4 h per axis Ambient temperature continued prEN 3155-015:200510 Table 7 (concluded) Applicable EN 2591- Test Not applicableAccording toEN 3155-001 Remarks 406 Mechanical endurance X 415 Test probe damage (female conta
36、ct) X 416 Contact bending strength X 417 Tensile strength (crimped connection) X 418 Gauge insertion/extraction forces (female contacts) X 424 Stripping force, solderless wrapped connections X 425 Unwrapping capability, solderless wrapped connections X 501 Soft solderability X 502 Restricted entry X
37、 503 Contact deformation after crimping X 507 Plating porosity X 508 Measurement of thickness of coating on contacts X The measured thickness shall be recorded 509 Adhesion of coating on contacts X 513 Magnetic permeability X 2 514 Solderability of contacts with self-contained solder and flux X 4.9
38、Gauges See EN 3155-001. prEN 3155-015:200511 5 Designation EXAMPLE Description block CONTACT ELECTRICAL Identity block EN3155-015F2020 Standard number Type of contact and identification code: F: female with two colour bands according to ISO 8843 or three colour bands according to SAE-AS-39029 S: fem
39、ale with three colour bands according to SAE-AS-39029 X: female with two colour bands according to ISO 8843 Contact size (see Table 1) Barrel size (see Table 1) NOTE If necessary, the code I9005 shall be placed between the description block and the identity block. 6 Marking See EN 3155-001. 7 Technical specification See EN 3155-001.
