1、Designation: A507 12Standard Specification forDrawing Alloy Steel, Sheet and Strip, Hot-Rolled and Cold-Rolled1This standard is issued under the fixed designation A507; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of la
2、st revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope*1.1 This specification covers hot-rolled a
3、nd cold-rolleddrawing alloy-steel sheet and strip. Material of this quality isproduced principally for applications involving severe coldplastic deformation such as deep drawn or severely formedparts. This steel is produced by a closely controlled steel-making practice designed to assure internal so
4、undness, relativeuniformity of chemical composition, and freedom from injuri-ous imperfections.1.2 The material covered by this specification may befurnished in several conditions, heat treatments, surface fin-ishes, and edges, as specified herein, in coils or cut lengths.2. Referenced Documents2.1
5、ASTM Standards:2A505 Specification for Steel, Sheet and Strip, Alloy, Hot-Rolled and Cold-Rolled, General Requirements forA941 Terminology Relating to Steel, Stainless Steel, Re-lated Alloys, and Ferroalloys3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 capable ofas used in t
6、his specification, means thattests need not be performed. However, if application by thepurchaser establishes that the material does not meet therequirements, the material shall be subject to rejection.3.1.2 drawing alloy steelalloy-steel sheet and strip in-tended for applications involving severe c
7、old plastic deforma-tion such as deep drawn or severely formed parts.3.1.3 standard steelssteel chemical compositions definedas “standard” by the Society of Automotive Engineers (SAE).See Table 1.3.1.4 steels other than standardsteel chemical composi-tions other than those defined as “standard,” and
8、 furnished tothe composition limits shown in Table 2.4. General Requirements and Ordering Information4.1 Material supplied to this specification shall conform toSpecification A505, which includes the general requirementsand establishes the rules for the ordering information thatshould be complied wi
9、th when purchasing material to thisspecification.4.2 In addition to the Ordering Information required bySpecification A505, the following shall also be included:4.2.1 Mechanical properties, if required (show propertiesdesired, which must be consistent with the grade and heattreatment),4.2.2 Surface
10、finish, if other than that normally furnished(see Section 10), and4.2.3 Application, or end use (identification of the part to bemade).5. Manufacture5.1 RollingThe material shall be furnished either hot-rolled or cold-rolled, as specified on the order.5.2 Heat TreatmentUnless otherwise specified on
11、theorder, the material shall be furnished spheroidize-annealed.(See Terminology A941 for heat treatment terms.)5.2.1 If the material is to be heat treated by other than theproducer, the order shall so state. The material may be orderedin the as-rolled condition, in such cases.6. Chemical Requirement
12、s Chemical Requirements6.1 The heat (cast) analysis shall conform to the require-ments for the grade specified on the order.6.1.1 Standard steels listed in Table 1 are those commonlyproduced for drawing alloy-steel sheet and strip.6.1.2 Nonstandard steel grades may be specified, using theranges and
13、limits shown in Table 2.7. Metallurgical Structure7.1 Microstructure:7.1.1 RequirementsAt least 75 % of the carbide micro-structure shall be of the globular type.1This specification is under the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel and Related Alloys and is the direct responsi
14、bility of SubcommitteeA01.19 on Steel Sheet and Strip.Current edition approved May 1, 2012. Published May 2012. Originallyapproved in 1964. Last previous edition approved in 2010 as A507 10. DOI:10.1520/A0507-12.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Cus
15、tomer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocke
16、n, PA 19428-2959, United States.7.1.2 Number of TestsThe number of tests shall be inaccordance with the producers standard quality control pro-cedures. A specific number of tests is not required, but thematerial shall be produced by manufacturing practices estab-lished to assure compliance with the
17、specified requirements.The material shall be subjected to mill tests and inspectionprocedures to assure such compliance. For government pro-curement, mill tests and inspection procedures utilized to showconformance to the microstructure requirements shall be madeavailable on request.8. Mechanical Re
18、quirements8.1 Tension and Hardness Tests:8.1.1 RequirementsWhen tension tests or hardness tests,or both are specified on the order, the test results shall conformto the requirements specified on the order. Yield strength,tensile strength, and elongation requirements may be specified.The tensile prop
19、erties will vary depending on the chemicalcomposition, condition, and heat treatment. Producers arefrequently consulted as to grade, resultant mechanical proper-ties, recommended heat treatment, and other informationneeded to establish the property parameters to meet end userequirements. Rockwell ha
20、rdness requirements may be speci-fied, providing the requirements are compatible with thetension test requirements.TABLE 1 Standard Steels Commonly Produced for Drawing Alloy-Steel Sheet and StripSteelDesignationNo.Chemical Composition Ranges and Limits, % (Heat Analysis)ACMnPSSiBNi Cr Mo VE3310C0.0
21、80.13 0.450.60 0.025 0.025 0.150.30 3.253.75 1.401.75 . . . . . .4012C0.090.14 0.751.00 0.025 0.025 0.150.30 . . . . . . 0.150.25 . . .4118 0.180.23 0.700.90 0.025 0.025 0.150.30 . . . 0.400.60 0.080.15 . . .4130 0.280.33 0.400.60 0.025 0.025 0.150.30 . . . 0.801.10 0.150.25 . . .4135 0.330.38 0.700
22、.90 0.025 0.025 0.150.30 . . . 0.801.10 0.150.25 . . .4137 0.350.40 0.700.90 0.025 0.025 0.150.30 . . . 0.801.10 0.150.25 . . .4140 0.380.43 0.751.00 0.025 0.025 0.150.30 . . . 0.801.10 0.150.25 . . .4142 0.400.45 0.751.00 0.025 0.025 0.150.30 . . . 0.801.10 0.150.25 . . .4145 0.430.48 0.751.00 0.02
23、5 0.025 0.150.30 . . . 0.801.10 0.150.25 . . .4147C0.450.50 0.751.00 0.025 0.025 0.150.30 . . . 0.801.10 0.150.25 . . .4150 0.480.53 0.751.00 0.025 0.025 0.150.30 . . . 0.801.10 0.150.25 . . .4320 0.170.22 0.450.65 0.025 0.025 0.150.30 1.652.00 0.400.60 0.200.30 . . .4340 0.380.43 0.600.80 0.025 0.0
24、25 0.150.30 1.652.00 0.700.90 0.200.30 . . .E4340 0.380.43 0.650.85 0.025 0.025 0.150.30 1.652.00 0.700.90 0.200.30 . . .4520C0.180.23 0.450.65 0.025 0.025 0.150.30 . . . . . . 0.450.60 . . .4615 0.130.18 0.450.65 0.025 0.025 0.150.30 1.652.00 . . . 0.200.30 . . .4620 0.170.22 0.450.65 0.025 0.025 0
25、.150.30 1.652.00 . . . 0.200.30 . . .4718 0.160.21 0.700.90 0.025 0.025 0.150.30 0.901.20 0.350.55 0.300.40 . . .4815 0.130.18 0.400.60 0.025 0.025 0.150.30 3.253.75 . . . 0.200.30 . . .4820 0.180.23 0.500.70 0.025 0.025 0.150.30 3.253.75 . . . 0.200.30 . . .5015 0.120.17 0.300.50 0.025 0.025 0.150.
26、30 . . . 0.300.50 . . . . . .5046 0.430.50 0.751.00 0.025 0.025 0.150.30 . . . 0.200.35 . . . . . .5115 0.130.18 0.700.90 0.025 0.025 0.150.30 . . . 0.700.90 . . . . . .5120 0.170.22 0.700.90 0.025 0.025 0.150.30 . . . 0.700.90 . . . . . .5130 0.280.33 0.700.90 0.025 0.025 0.150.30 . . . 0.801.10 .
27、. . . . .5132 0.300.35 0.600.80 0.025 0.025 0.150.30 . . . 0.751.00 . . . . . .5140 0.380.43 0.700.90 0.025 0.025 0.150.30 . . . 0.700.90 . . . . . .5150 0.480.53 0.790.90 0.025 0.025 0.150.30 . . . 0.700.90 . . . . . .5160 0.560.64 0.751.00 0.025 0.025 0.150.30 . . . 0.700.90 . . . . . .E51100C0.95
28、1.10 0.250.45 0.025 0.025 0.150.30 . . . 0.901.15 . . . . . .E52100 0.981.10 0.250.45 0.025 0.025 0.150.30 . . . 1.301.60 . . . . . .6150 0.480.53 0.700.90 0.025 0.025 0.150.30 . . . 0.801.10 . . . 0.15 min6158C0.550.62 0.701.10 0.025 0.015 0.150.30 . . . 0.901.20 . . . 0.100.208615 0.130.18 0.700.9
29、0 0.025 0.025 0.150.30 0.400.70 0.400.60 0.150.25 . . .8617 0.150.20 0.700.90 0.025 0.025 0.150.30 0.400.70 0.400.60 0.150.25 . . .8620 0.180.23 0.700.90 0.035 0.035 0.150.30 0.400.70 0.400.60 0.150.25 . . .8630 0.280.33 0.700.90 0.025 0.025 0.150.30 0.400.70 0.400.60 0.150.25 . . .8640 0.380.43 0.7
30、51.00 0.025 0.025 0.150.30 0.400.70 0.400.60 0.150.25 . . .8642C0.400.45 0.751.00 0.025 0.025 0.150.30 0.400.70 0.400.60 0.150.25 . . .8645 0.430.48 0.751.00 0.025 0.025 0.150.30 0.400.70 0.400.60 0.150.25 . . .8650C0.480.53 0.751.00 0.025 0.025 0.150.30 0.400.70 0.400.60 0.150.25 . . .8655 0.510.59
31、 0.751.00 0.025 0.025 0.150.30 0.400.70 0.400.60 0.150.25 . . .8660 0.550.65 0.751.00 0.025 0.025 0.150.30 0.400.70 0.400.60 0.150.25 . . .8720 0.180.23 0.700.90 0.025 0.025 0.150.30 0.400.70 0.400.60 0.200.30 . . .8735C0.330.38 0.751.00 0.025 0.025 0.150.30 0.400.70 0.400.60 0.200.30 . . .8740C0.38
32、0.43 0.751.00 0.025 0.025 0.150.30 0.400.70 0.400.60 0.200.30 . . .9260 0.560.64 0.751.00 0.025 0.025 1.802.20 . . . . . . . . . . . .9262C0.550.65 0.751.00 0.025 0.025 1.802.20 . . . 0.250.40 . . . . . .E9310C0.080.13 0.450.65 0.025 0.025 0.200.35 3.003.50 1.001.40 0.080.15 . . .AThe chemical range
33、s and limits shown are subject to product analysis tolerances. See Specification A505.BOther silicon limits can be substituted on agreement between the purchaser and producer.CNot an S.A.E. Steel Designation.A507 1228.1.2 Number of TestsTwo tension tests and two hardnesstests, when specified, shall
34、be taken at random from each heat(cast) and heat treatment lot.9. Other Tests and Requirements9.1 End Use Suitability:9.1.1 When steel is to be furnished in the spheroidize-annealed condition, the user and producer shall review anypart(s) to be produced to reach adequate agreement on capa-bility to
35、produce said parts.9.1.2 Material in the spheroidize-annealed condition gener-ally work hardens and may require stress-relief-annealingbetween drawing operations.10. Workmanship, Finish, and Appearance10.1 Surface Finish:10.1.1 Hot-RolledUnless otherwise specified, hot-rolledmaterial shall be furnis
36、hed descaled and oiled. When required,the material may be specified to be furnished not oiled.10.1.2 Cold-RolledUnless otherwise specified, cold-rolled material shall be furnished with a commercial dull mattefinish and shall be oiled. When required, the material may bespecified to be furnished not o
37、iled.10.2 Edges:10.2.1 Hot-RolledUnless otherwise specified, hot-rolledmaterial shall be furnished with Mill Edge. The material maybe specified to have other types of edges, in accordance withSpecification A505.10.2.2 Cold-RolledUnless otherwise specified, cold-rolled sheet shall be furnished with C
38、ut Edge and cold-rolledstrip shall be furnished with No. 3 Edge. The material may bespecified to have other types of edges, in accordance withSpecification A505.11. Keywords11.1 alloy steel with improved formability; cold-rolled alloysteel; deep drawn alloy steel; drawing alloy steel sheet;drawing a
39、lloy steel strip; forming alloy steel; hot-rolled alloysteel; special soundness alloy steelSUMMARY OF CHANGESCommittee A01 has identified the location of selected changes to this standard since the last issue (A507 10)that may impact the use of this standard. (Approved May 1, 2012.)(1) Removed UNS a
40、nd SAE designators, revised five chemicalcompositions, and added Footnote C to Table 1.Committee A01 has identified the location of selected changes to this standard since the last issue (A507 06)that may impact the use of this standard. (Approved April 1, 2010.)(1) Footnote B added to Table 1.TABLE
41、 2 Heat (Cast) Analysis Ranges for Other Than StandardSteel Alloy Sheet and StripElementWhen Maximum ofSpecified Element Is, %Range orLimit, %Carbon To 0.55 incl 0.05Over 0.55 to 0.70 incl 0.08Over 0.70 to 0.80 incl 0.10Over 0.80 to 0.95 incl 0.12Over 0.95 to 1.35 incl 0.13Manganese To 0.60 incl 0.2
42、0Over 0.60 to 0.90 incl 0.20Over 0.90 to 1.05 incl 0.25Over 1.05 to 1.90 incl 0.30Over 1.90 to 2.10 incl 0.40Phosphorus . . . 0.025 maxSulfur . . . 0.025 maxSilicon To 0.15 incl 0.08Over 0.15 to 0.20 incl 0.10Over 0.20 to 0.40 incl 0.15Over 0.40 to 0.60 incl 0.20Over 0.60 to 1.00 incl 0.30Over 1.00
43、to 2.20 incl 0.40Copper To 0.60 inclOver 0.60 to 1.50 inclOver 1.50 to 2.00 incl0.200.300.35Nickel To 0.50 incl 0.20Over 0.50 to 1.50 incl 0.30Over 1.50 to 2.00 incl 0.35Over 2.00 to 3.00 incl 0.40Over 3.00 to 5.30 incl 0.50Over 5.30 to 10.00 incl 1.00Chromium To 0.40 incl 0.15Over 0.40 to 0.90 incl
44、 0.20Over 0.90 to 1.05 incl 0.25Over 1.05 to 1.60 incl 0.30Over 1.60 to 1.75 incl 0.35Over 1.75 to 2.10 incl 0.40Over 2.10 to 3.99 incl 0.50Molybdenum To 0.10 incl 0.05Over 0.10 to 0.20 incl 0.07Over 0.20 to 0.50 incl 0.10Over 0.50 to 0.80 incl 0.15Over 0.80 to 1.15 incl 0.20Vanadium To 0.25 inclOve
45、r 0.25 to 0.50 incl0.050.10A507 123ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk
46、of infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this
47、 standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake y
48、our views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).A507 124
