ASTM C1244-2011(2017) Standard Test Method for Concrete Sewer Manholes by the Negative Air Pressure (Vacuum) Test Prior to Backfill《回填之前利用负压(真空)试验的混凝土污水管检查孔的标准试验方法》.pdf
《ASTM C1244-2011(2017) Standard Test Method for Concrete Sewer Manholes by the Negative Air Pressure (Vacuum) Test Prior to Backfill《回填之前利用负压(真空)试验的混凝土污水管检查孔的标准试验方法》.pdf》由会员分享,可在线阅读,更多相关《ASTM C1244-2011(2017) Standard Test Method for Concrete Sewer Manholes by the Negative Air Pressure (Vacuum) Test Prior to Backfill《回填之前利用负压(真空)试验的混凝土污水管检查孔的标准试验方法》.pdf(4页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: C1244 11 (Reapproved 2017)Standard Test Method forConcrete Sewer Manholes by the Negative Air Pressure(Vacuum) Test Prior to Backfill1This standard is issued under the fixed designation C1244; the number immediately following the designation indicates the year oforiginal adoption or, in
2、 the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers procedures for testing precastconcrete manhole sections whe
3、n using the vacuum test methodto demonstrate the integrity of the installed materials and theconstruction procedures. This test method is used for testingconcrete manhole sections utilizing mortar, mastic, or gasketedjoints.1.2 This test method is intended to be used as a preliminarytest to enable t
4、he installer to demonstrate the condition of theconcrete manholes prior to backfill. Users are hereby cautionedthat misuse or misapplication of the test criteria containedherein can cause permanent damage to the system being tested.NOTE 1Vacuum test criteria presented in this test method are similar
5、to those in general use. The test and criteria have been widely andsuccessfully used in testing manholes.NOTE 2The user of this test method is advised that no correlation hasbeen found between vacuum (air) and hydrostatic tests.1.3 This test method is the companion to metric TestMethod C1244M; there
6、fore, no SI equivalents are shown inthis test method.1.4 This standard does not purport to address all of thesafety problems, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility o
7、f regulatory limitations prior to use.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World T
8、rade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2C822 Terminology Relating to Concrete Pipe and RelatedProductsC924 Practice for Testing Concrete Pipe Sewer Lines byLow-Pressure Air Test Method (Withdrawn 2013)3C969 Practice for Infiltration and
9、 Exfiltration AcceptanceTesting of Installed Precast Concrete Pipe Sewer LinesC1244M Test Method for Concrete Sewer Manholes by theNegative Air Pressure (Vacuum) Test Prior to Backfill(Metric)3. Terminology3.1 For definitions of terms relating to manholes, seeTerminology C822.4. Summary of Practice4
10、.1 All lift holes and any pipes entering the manhole are tobe plugged.Avacuum will be drawn and the vacuum drop overa specified time period is used to determine the acceptability ofthe manhole.5. Significance and Use5.1 This is not a routine test. The values recorded areapplicable only to the manhol
11、e being tested and at the time oftesting.6. Preparation of the Manhole6.1 All lift holes shall be plugged.6.2 All pipes entering the manhole shall be temporarilyplugged, taking care to securely brace the pipes and plugs toprevent them from being drawn into the manhole.1This test method is under the
12、jurisdiction of ASTM Committee C13 onManholes and Specials.Current edition approved April 1, 2017. Published April 2017. Originallyapproved in 1993. Last previous edition approved in 2011 as C1244 11. DOI:10.1520/C1244-11R17.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcon
13、tact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.Copyright ASTM International, 100 Barr Harbor Drive,
14、 PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issue
15、d by the World Trade Organization Technical Barriers to Trade (TBT) Committee.17. Procedure7.1 The test head shall be placed at the top of the manholein accordance with the manufacturers recommendations.7.2 A vacuum of 10 in. Hg shall be drawn on the manhole,the valve on the vacuum line of the test
16、head closed, and thevacuum pump shut off. The time shall be measured for thevacuum to drop to 9 in. Hg.7.3 The manhole is acceptable if the time for the vacuumreading to drop from 10 in. Hg to 9 in. Hg meets or exceeds thevalues indicated in Table 1.7.4 If the manhole fails the initial test, the man
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
最后一页预览完了!喜欢就下载吧,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMC124420112017STANDARDTESTMETHODFORCONCRETESEWERMANHOLESBYTHENEGATIVEAIRPRESSUREVACUUMTESTPRIORTOBACKFILL

链接地址:http://www.mydoc123.com/p-463897.html