ASTM F2274-2011(2016) Standard Specification for Condition 3 Bicycle Forks《条件3自行车轮叉标准规范》.pdf
《ASTM F2274-2011(2016) Standard Specification for Condition 3 Bicycle Forks《条件3自行车轮叉标准规范》.pdf》由会员分享,可在线阅读,更多相关《ASTM F2274-2011(2016) Standard Specification for Condition 3 Bicycle Forks《条件3自行车轮叉标准规范》.pdf(2页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: F2274 11 (Reapproved 2016) An American National StandardStandard Specification forCondition 3 Bicycle Forks1This standard is issued under the fixed designation F2274; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the
2、 year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification establishes testing requirements forqualifying designs using production forks intended for
3、 use inCondition 3 per Classification F2043.2. Referenced Documents2.1 ASTM Standards:2F2043 Classification for Bicycle UsageF2273 Test Methods for Bicycle Forks3. Classification3.1 Condition 3 per Classification F2043.4. Sampling and Test Specimens4.1 Selection and Preparation of Specimens:4.1.1 Th
4、ree forks shall be randomly selected from the firstproduction lot for the fatigue plus impact test per this specifi-cation.4.1.2 One fork shall be randomly selected for the impact testper this specification.4.1.3 One fork shall be randomly selected for both thecompression and bending tests per this
5、specification.5. Performance Requirements5.1 Bicycle forks intended by the manufacturer to be usedaccording to Condition 3 shall be tested per Test MethodsF2273.5.1.1 Compression Load Test:5.1.1.1 The fork shall withstand a compression load of 2800N without any component failure, fracture or permane
6、ntdeformation.5.1.1.2 Under the application of the compression load of2800 N, the minimum clearance from the maximum tire profileintended for use by the manufacturer to the nearest surface ofthe crown shall be at least 3 mm.5.1.2 Bending Load Test:5.1.2.1 The fork shall withstand a maximum bending l
7、oadof 1500 N (100 N initial load plus an additional 1400 N).5.1.2.2 The permanent deflection of a rigid fork shall notexceed 5 mm and the permanent deflection of a suspension forkshall not exceed 10 mm.5.1.3 Impact Resistance Test:5.1.3.1 For each fork, permanent deflection shall be lessthan 45 mm f
8、ollowing impact of a 22.5 kg mass dropped fromheight number 1, and the sample shall not develop cracks orfractures. The velocity at impact shall be at least 2.66 m/s. Notethat in a frictionless system, this velocity would be achievedwith a drop height of 360 mm.5.1.3.2 For each fork, following impac
9、t of a 22.5 kg massdropped from height number 2, the connection between thesteerer tube and crown must withstand at least 108.5 Nm oftorque without rotation. The velocity at impact from dropheight number 2 shall be at least 3.43 m/s. Note that in africtionless system, this velocity would be achieved
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
最后一页预览完了!喜欢就下载吧,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMF227420112016STANDARDSPECIFICATIONFORCONDITION3BICYCLEFORKS 条件 自行 车轮 标准规范 PDF
![提示](http://www.mydoc123.com/images/bang_tan.gif)
链接地址:http://www.mydoc123.com/p-538279.html