1、BS EN 4536-2:2009ICS 49.035NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDAerospace series Bushes, plain in corrosion-resisting steel with self-lubricating liner, elevated load Part 2: Dimensions and loads Inch seriesThis British Standardwas published under the
2、authority of the StandardsPolicy and StrategyCommittee on 31 July2009. BSI 2009ISBN 978 0 580 57132 9Amendments/corrigenda issued since publicationDate CommentsBS EN 4536-2:2009National forewordThis British Standard is the UK implementation of EN 4536-2:2009.The UK participation in its preparation w
3、as entrusted to TechnicalCommittee ACE/12, Aerospace fasteners and fastening systems.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its
4、correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.BS EN 4536-2:2009EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 4536-2July 2009ICS 49.035English VersionAerospace series - Bushes, plain in corrosion resisting steel withself-lubricating liner, ele
5、vated load - Part 2: Dimensions andloads - Inch seriesSrie arospatiale - Bagues en acier rsistant lacorrosion garniture autolubrifiante, charge leve - Partie2: Dimensions et charges - Srie en inchesLuft- und Raumfahrt - Buchsen aus korrosionsbestndigemStahl, mit selbstschmierender Beschichtung, erhh
6、teBelastung - Teil 2: Mae und Belastungen - Inch ReiheThis European Standard was approved by CEN on 23 April 2009.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any al
7、teration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by tra
8、nslationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany,
9、 Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManageme
10、nt Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 4536-2:2009: EBS EN 4536-2:2009EN 4536-2:2009 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Terms and definitions .4
11、4 Requirements .44.1 Configuration, dimensions, tolerances and mass .44.2 Surface roughness 44.3 Materials .54.4 Surface treatment 55 Designation . 126 Marking 127 Technical specification 128 Design recommendation 12BS EN 4536-2:2009EN 4536-2:2009 (E) 3 Foreword This document (EN 4536-2:2009) has be
12、en prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member
13、 countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2010, and conflicting national standards shall be withdrawn at the latest by January 20
14、10. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organiza
15、tions of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Roman
16、ia, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 4536-2:2009EN 4536-2:2009 (E) 4 1 Scope This standard specifies the characteristics of plain bushes in corrosion resisting steel with self-lubricating liner, elevated load for aerospace applications. The bushes are inte
17、nded for use in fixed or moving parts of the aircraft structure and control mechanisms. They shall be used in the temperature range 55 C to 163 C. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition
18、cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2311, Aerospace series Bushes with self-lubricating liner Technical specification EN 2424, Aerospace series Marking of aerospace products EN 3161, Aerospace series Steel FE-PM3
19、801 (X5CrNiCu17-4) Air melted, solution treated and precipitation treated, bar a or D 200 mm, Rm 930 MPa TR 4475, Aerospace series Bearings and mechanical transmissions for airframe applications Vocabulary 1) ISO 2768-1, General tolerances Part 1: Tolerances for linear and angular dimensions without
20、 individual tolerance indications ISO 8075, Aerospace Surface treatment of hardenable stainless steel parts 3 Terms and definitions For the purposes of this document, the terms and definitions given in TR 4475 apply. 4 Requirements 4.1 Configuration, dimensions, tolerances and mass According to Figu
21、re 1 and Tables 1 and 2. Dimensions apply after surface treatment. Dimensions and tolerances are expressed in millimetres (inches). General tolerances shall be ISO 2768-m in accordance with ISO 2768-1. 4.2 Surface roughness According to Figure 1. 1) Published as ASD Technical Report at the date of p
22、ublication of this standard. BS EN 4536-2:2009EN 4536-2:2009 (E) 5 4.3 Materials Bush: Stainless steel according to EN 3161 Liner: Self-lubricating wear resistant material consistent with the requirements of EN 2311 4.4 Surface treatment Code T: Passivation according to ISO 8075. Key aChamfer machin
23、ed before bonding bChamfer or radius at manufacturers option cChamfer machined after bonding Figure 1 Configuration BS EN 4536-2:2009EN 4536-2:2009 (E) 6 Table 1 Dimensions and tolerances Diameter code a d D a Nominal diameter 0 0,025 0 0,013 2 (0 0.0010) (0 0.0005) 04 6,350 (0.2500) 6,388 (0.2515)
24、9,550 (0.3760) 0,50 to 0,75 (0.020 to 0.030) 15 05 7,938 (0.3125) 7,976 (0.3140) 11,140 (0.4386) 06 9,525 (0.3750) 9,563 (0.3765) 12,730 (0.5012) 07 11,113 (0.4375) 11,151 (0.4390) 14,321 (0.5638) 08 12,700 (0.5000) 12,738 (0.5015) 15,913 (0.6265) 09 14,288 (0.5625) 14,326 (0.5640) 17,506 (0.6892) 1
25、0 15,875 (0.6250) 15,913 (0.6265) 20,681 (0.8142) 11 17,463 (0.6875) 17,501 (0.6890) 22,268 (0.8767) 12 19,050 (0.7500) 19,088 (0.7515) 23,858 (0.9393) 14 22,225 (0.8750) 22,263 (0.8765) 27,038 (1.0645) 16 25,400 (1.0000) 25,438 (1.0015) 30,221 (1.1898) 18 28,575 (1.1250) 28,613 (1.1265) 33,396 (1.3
26、148) 20 31,750 (1.2500) 31,788 (1.2515) 36,571 (1.4398) 22 34,925 (1.3750) 34,963 (1.3765) 39,746 (1.5648) 24 38,100 (1.5000) 38,138 (1.5015) 44,508 (1.7523) 26 41,275 (1.6250) 41,313 (1.6265) 47,683 (1.8773) 28 44,450 (1.7500) 44,488 (1.7515) 50,858 (2.0023) 32 50,800 (2.0000) 50,838 (2.0015) 57,20
27、8 (2.2523) aDiameter code corresponds to nominal diameter d in 1/16 inch. BS EN 4536-2:2009EN 4536-2:2009 (E) 7 Table 2 Mass Dia-meter code aLength code b005 006 007 008 009 010 011 012 014 016 018 020 022 024 028 l 00,25(00.010) 3,97 4,76 5,56 6,35 7,14 7,94 8,73 9,53 11,11 12,70 14,29 15,88 17,46
28、19,05 22,23 (0.156) (0.188) (0.219) (0.250) (0.281) (0.313) (0.344) (0.375) (0.438) (0.500) (0.563) (0.625) (0.688) (0.750) (0.875)Mass in kg/1 000 pieces 04 1,23 1,47 1,72 1,96 2,21 2,45 2,70 2,94 05 1,47 1,77 2,06 2,35 2,65 2,94 3,24 3,53 4,12 06 1,72 2,06 2,40 2,75 3,09 3,43 3,78 4,12 4,81 5,49 6
29、,18 07 1,96 2,36 2,75 3,14 3,53 3,93 4,32 4,71 5,50 6,28 7,07 7,85 08 2,21 2,65 3,10 3,54 3,98 4,42 4,87 5,31 6,19 7,08 7,96 8,85 9,73 09 2,46 2,95 3,45 3,94 4,43 4,92 5,41 5,91 6,89 7,88 8,86 9,84 10,83 11,81 10 4,24 5,09 5,94 6,79 7,64 8,48 9,33 10,18 11,88 13,57 15,27 16,97 18,66 20,36 23,75 11 6
30、,80 8,30 9,22 10,14 11,06 12,91 14,75 16,60 18,44 20,28 22,13 25,81 12 7,97 8,97 9,96 10,96 11,95 13,95 15,94 17,93 19,92 21,92 23,91 27,89 14 8,51 10,30 11,45 12,59 13,74 16,03 18,32 20,61 22,90 25,18 27,47 32,05 16 10,36 11,65 12,94 14,24 15,53 18,12 20,71 23,30 25,89 28,48 31,07 36,24 18 14,42 15
31、,88 17,31 20,19 23,07 25,96 28,84 31,73 34,61 40,38 20 19,08 22,26 25,44 28,62 31,80 34,98 38,16 44,51 22 20,85 24,33 27,80 31,28 34,75 38,23 41,70 48,65 24 30,72 35,84 40,96 46,08 51,20 56,32 61,44 71,68 26 44,11 49,62 55,14 60,65 66,16 77,19 28 47,26 53,16 59,07 64,98 70,88 82,70 32 53,55 60,24 66
32、,94 73,63 80,33 93,71 continued BS EN 4536-2:2009EN 4536-2:2009 (E) 8 Table 2 (concluded) Dia-meter code aLength code b032 036 040 044 048 052 056 060 064 068 072 076 080 088 096 l 00,25(00.010) 25,40 28,58 31,75 34,93 38,10 41,28 44,45 47,63 50,80 53,98 57,15 60,33 63,50 69,85 76,20 (1.000) (1.125)
33、 (1.250) (1.375) (1.500) (1.625) (1.750) (1.875) (2.000) (2.125) (2.250) (2.375) (2.500) (2.750) (3.000)Mass in kg/1 000 pieces 04 05 06 07 08 09 10 11 29,50 12 31,88 14 36,63 41,21 45,79 16 41,42 46,60 51,78 56,96 18 46,15 51,92 57,69 63,45 69,22 20 50,87 57,23 63,59 69,95 76,31 82,67 89,03 22 55,6
34、0 62,55 69,50 76,45 83,40 90,35 97,30 104,25 24 81,92 92,16 102,40 112,64 122,88 133,12 143,36 153,60 163,85 174,09 26 88,22 99,24 110,27 121,30 132,33 143,35 154,38 165,41 176,43 187,46 198,49 28 94,51 106,33 118,14 129,95 141,77 153,58 165,39 177,21 189,02 200,84 212,65 224,46 32 107,10 120,49 133
35、,88 147,26 160,65 174,04 187,43 200,81 214,20 227,59 240,98 254,36 267,75 294,53 aDiameter code corresponds to nominal diameter d in 1/16 inch. bLength code corresponds to length l in 1/32 inch. BS EN 4536-2:2009EN 4536-2:2009 (E) 9 Table 3 Loads Diameter code aLength code Permissible radial load Ra
36、dial load Diameter code aLength code Permissible radial load Radial load kN kN Static CsbDynamic C25cStatic CsbDynamic C25c04 005 6,80 3,26 08 018 84,68 40,54 006 9,55 4,57 020 95,62 45,78 007 12,29 5,88 022 106,56 51,01 008 15,03 7,20 09 005 15,26 7,30 009 17,78 8,51 006 21,41 10,25 010 20,52 9,82
37、007 27,56 13,19 011 23,26 11,14 008 33,71 16,14 012 26,01 12,45 009 39,86 19,09 05 005 8,49 4,07 010 46,02 22,03 006 11,92 5,71 011 52,17 24,98 007 15,34 7,35 012 58,32 27,92 008 18,77 8,99 014 70,62 33,81 009 22,19 10,63 016 82,93 39,70 010 25,62 12,26 018 95,23 45,59 011 29,04 13,90 020 107,53 51,
38、48 012 32,47 15,54 022 119,84 57,37 014 39,32 18,82 024 132,14 63,26 06 005 10,19 4,88 10 005 16,95 8,11 006 14,29 6,84 006 23,78 11,39 007 18,40 8,81 007 30,62 14,66 008 22,51 10,77 008 37,45 17,93 009 26,61 12,74 009 44,28 21,20 010 30,72 14,71 010 51,12 24,47 011 34,83 16,67 011 57,95 27,74 012 3
39、8,93 18,64 012 64,78 31,01 014 47,14 22,57 014 78,45 37,56 016 55,36 26,50 016 92,12 44,10 018 63,57 30,43 018 105,78 50,64 07 005 11,88 5,69 020 119,45 57,19 006 16,66 7,98 022 133,12 63,73 007 21,45 10,27 024 146,78 70,27 008 26,24 12,56 028 174,12 83,36 009 31,03 14,86 11 008 41,19 19,72 010 35,8
40、2 17,15 009 48,70 23,31 011 40,61 19,44 010 56,22 26,91 012 45,39 21,73 011 63,73 30,51 014 54,97 26,32 012 71,25 34,11 016 64,55 30,90 014 86,28 41,30 018 74,12 35,49 016 101,31 48,50 020 83,70 40,07 018 116,34 55,70 08 005 13,57 6,50 020 131,37 62,89 006 19,04 9,11 022 146,40 70,09 007 24,51 11,73
41、 024 161,43 77,28 008 29,98 14,35 028 191,49 91,67 009 35,45 16,97 032 221,55 106,06 010 40,92 19,59 12 008 44,92 21,51 011 46,39 22,21 009 53,12 25,43 012 51,86 24,83 010 61,31 29,35 014 62,80 30,06 011 69,51 33,28 016 73,74 35,30 012 77,71 37,20 continuedBS EN 4536-2:2009EN 4536-2:2009 (E) 10 Tabl
42、e 3 (continued) Diameter code aLength code Permissible radial load Radial load Diameter code aLength code Permissible radial load Radial load kN kN Static CsbDynamic C25cStatic CsbDynamic C25c12 014 94,10 45,05 18 036 411,37 196,94 016 110,50 52,90 040 460,52 220,47 018 126,89 60,75 044 509,67 244,0
43、0 020 143,28 68,60 048 558,82 267,53 022 159,68 76,44 20 012 129,41 61,95 024 176,07 84,29 014 156,71 75,02 028 208,86 99,99 016 184,01 88,09 032 241,64 115,69 018 211,31 101,16 14 008 52,39 25,08 020 238,61 114,23 009 61,95 29,66 022 265,91 127,30 010 71,51 34,24 024 293,22 140,37 011 81,07 38,81 0
44、28 347,82 166,51 012 90,63 43,39 032 402,42 192,65 014 109,75 52,54 036 457,02 218,80 016 128,87 61,70 040 511,62 244,94 018 147,99 70,85 044 566,22 271,08 020 167,12 80,01 048 620,82 297,22 022 186,24 89,16 052 675,43 323,36 024 205,36 98,31 056 730,03 349,50 028 243,60 116,62 22 012 142,34 68,14 0
45、32 281,84 134,93 014 172,36 82,52 036 320,08 153,24 016 202,39 96,89 040 358,32 171,54 018 232,42 111,27 16 008 59,86 28,66 020 262,45 125,64 009 70,79 33,89 022 292,47 140,02 010 81,71 39,12 024 322,50 154,40 011 92,64 44,35 028 382,56 183,15 012 103,56 49,58 032 442,61 211,90 014 125,41 60,04 036
46、502,67 240,65 016 147,25 70,50 040 562,72 269,40 018 169,10 80,96 044 622,78 298,15 020 190,95 91,41 048 682,83 326,90 022 212,80 101,89 052 742,89 355,65 024 234,64 112,33 056 802,94 384,40 028 278,34 133,25 060 863,00 413,15 032 322,03 154,17 24 012 155,26 74,33 036 365,73 175,09 014 188,02 90,01
47、040 409,42 196,01 016 220,77 105,69 044 453,11 216,93 018 253,52 121,37 18 010 91,91 44,00 020 286,28 137,05 011 104,20 49,88 022 319,03 152,73 012 116,48 55,77 024 351,79 168,42 014 141,06 67,53 028 417,30 199,78 016 165,63 79,30 032 482,81 231,14 018 190,21 91,06 036 548,31 262,50 020 214,78 102,82 040 613,82 293,86 022 239,35 114,59 044 679,33 325,23 024 263,93 126,35 048 744,84 356,59 028 313,08 149,88 052 810,35 387,95 032 362,22 173,41 056 875,86 419,31 continuedBS EN 4536-2:2009EN 4536-
