1、BSI Standards PublicationBS EN 16724:2015Thermal insulation productsfor building applications Instructions for mounting andfixing for determination ofthe reaction to fire testing ofexternal thermal Insulationcomposite systems (ETICS)BS EN 16724:2015 BRITISH STANDARDNational forewordThis British Stan
2、dard is the UK implementation of EN 16724:2015. The UK participation in its preparation was entrusted to TechnicalCommittee B/540, Energy performance of materials components and buildings.A list of organizations represented on this committee can be obtained on request to its secretary.This publicati
3、on does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 85702 7 ICS 91.100.60 Compliance with a British Standard cannot confer immunity f
4、rom legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 April 2016.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS EN 16724:2015EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 16724 December
5、2015 ICS 91.100.60 English Version Thermal insulation products for building applications - Instructions for mounting and fixing for determination of the reaction to fire testing of external thermal Insulation composite systems (ETICS) Produits isolants thermiques pour le btiment - Instructions de mo
6、ntage et de fixation pour lessai de raction au feu des systmes composites disolation thermique par lextrieur (ITE) Wrmedmmstoffe fr Gebude - Einbau- und Befestigungsbedingungen fr die Prfung des Brandverhaltens von auenseitigen Wrmedmm-Verbundsystemen (WDVS) This European Standard was approved by CE
7、N on 24 October 2015. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standard
8、s may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notif
9、ied to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Ice
10、land, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey andUnited Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Manag
11、ement Centre: Avenue Marnix 17, B-1000 Brussels 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16724:2015 EBS EN 16724:2015 EN 16724:2015 (E) 2 Contents PageEuropean foreword . 3 1 Scope 4 2 Normative references 4 3 Terms and
12、 definitions . 4 4 Principle . 6 5 Instructions for mounting and fixing, field of application . 6 5.1 General 6 5.2 Testing according to EN ISO 1182 (Non-combustibility test) 7 5.2.1 General 7 5.2.2 Base coat and finishing coats 7 5.2.3 Reinforcement 7 5.2.4 Thermal insulation products 7 5.2.5 Adhes
13、ives . 8 5.2.6 Key coat and decorative coat 8 5.3 Testing according to EN ISO 1716 (Heat of combustion, QPCS-Value) 85.3.1 General 8 5.3.2 Base coat and finishing coat 8 5.3.3 Reinforcement 8 5.3.4 Thermal insulation products 8 5.3.5 Adhesives . 8 5.3.6 Calculation of the highest gross heat of combu
14、stion of a kit QPCS, kit, decisive85.3.7 Key coat and decorative coat 8 5.4 Testing according to EN 13823 (Single burning item SBI) 9 5.4.1 General 9 5.4.2 Test specimen . 9 5.4.3 Base coat and finishing coat 9 5.4.4 Reinforcement . 10 5.4.5 Thermal insulation products . 10 5.4.6 Adhesives 11 Figure
15、 1 Schematic drawing of the test specimen in the SBI-test according to EN 13823 11 5.4.7 Key coat and decorative coat . 12 5.5 Testing according to EN ISO 11925-2 (Small flame test) . 12 5.5.1 General . 12 5.5.2 Test specimen 12 5.5.3 Base coat and finishing coats . 12 5.5.4 Reinforcement . 12 5.5.5
16、 Thermal insulation products . 12 5.5.6 Adhesives 13 5.5.7 Key coat and decorative coat . 14 6 Test results and classification report . 14 Annex A (informative) Calculation of QPCS, kit, decisive(formulae and example) 15A.1 General . 15 Table A.1 Data of the ETICS-components . 15 A.2 Conversion 16 B
17、S EN 16724:2015 EN 16724:2015 (E) 3 European foreword This document (EN 16724:2015) has been prepared by Technical Committee CEN/TC 88 “Thermal insulating materials and products”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either
18、 by publication of an identical text or by endorsement, at the latest by June 2016, and conflicting national standards shall be withdrawn at the latest by June 2016. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENEL
19、EC shall not be held responsible for identifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republi
20、c, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 1
21、6724:2015 EN 16724:2015 (E) 4 1 Scope This European Standard specifies instructions for mounting and fixing for reaction to fire testing for External Thermal Insulation Composite Systems (ETICS) and gives rules for the field of application of test results. 2 Normative references The following docume
22、nts, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 13238, Reaction to fire
23、tests for building products - Conditioning procedures and general rules for selection of substrates EN 13501-1:2007+A1:2009, Fire classification of construction products and building elements - Part 1: Classification using data from reaction to fire tests EN 13823, Reaction to fire tests for buildin
24、g products - Building products excluding floorings exposed to the thermal attack by a single burning item EN 15725, Extended application reports on the fire performance of construction products and building elements EN ISO 1182, Reaction to fire tests for products - Non-combustibility test (ISO 1182
25、) EN ISO 1716, Reaction to fire tests for products - Determination of the gross heat of combustion (calorific value) (ISO 1716) EN ISO 9229, Thermal insulation - Vocabulary (ISO 9229) EN ISO 11925-2, Reaction to fire tests - Ignitability of products subjected to direct impingement of flame - Part 2:
26、 Single-flame source test (ISO 11925-2) 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN ISO 9229 and the following apply. 3.1 gross heat of combustion QPCSheat of combustion of a substance when the combustion is complete and any produced water is enti
27、rely condensed under specified conditions Note 1 to entry: The gross heat of combustion is expressed in mega joules per kilogram. 3.2 adhesive component used for bonding the thermal insulation product to the substrate BS EN 16724:2015 EN 16724:2015 (E) 5 3.3 anchors for thermal insulation products f
28、ixing device consisting of a plate for fixing the thermal insulation product and if appropriate also the reinforced base coat, a sleeve which passes through the thermal insulation product and a part which is embedded or otherwise affixed to the substrate 3.4 anchors for profiles and rails device for
29、 fixing the profiles or rails to the substrate 3.5 ancillary material any supplementary component used in addition to the kit, which shall be used according to system holders application rules Note 1 to entry: Ancillary materials are used e.g. to form joints or to achieve continuity or to give speci
30、fic protection (mastics, joint-covers, corner stripes, corner profiles, base profiles, fire barriers etc.) 3.6 base coat component applied directly by rendering on to the thermal insulation product 3.7 component group of factory-made products fulfilling the same functions as a part of the design ETI
31、CS 3.8 finishing coat component applied to the reinforced base coat, possibly preceded by a key coat 3.9 glass fibre mesh as reinforcement textile fabrics consisting of continuous glass filament yarn in both the warp and the weft directions embedded in the base coat 3.10 metal mesh as reinforcement
32、galvanized steel or stainless steel mesh fixed with anchors embedded in the reinforced base coat 3.11 mechanical fixing device device for fixing assembled kits to the substrate EXAMPLE Rails, anchors, profiles 3.12 substrate part of the wall/test assembly to which the kit is fixed 3.13 substantial c
33、omponents material that constitutes a significant part of a non-homogeneous product. A layer with a mass/unit area 1,0 kg/m2or a thickness 1,0 mm is considered to be a substantial component SOURCE: EN 13501-1:2007+A1:2009, 3.1.5 BS EN 16724:2015 EN 16724:2015 (E) 6 3.14 non-substantial components ma
34、terial that does not constitute a significant part of a non-homogeneous product. A layer with a mass/unit area 1,0 kg/m2and a thickness 1,0 mm is considered to be a non-substantial component Note 1 to entry: Two or more non-substantial layers that are adjacent to each other (i.e. with no substantial
35、 component(s) in between the layers) are regarded as one non-substantial component when they collectively comply with the requirements for a layer being a non-substantial component. SOURCE: EN 13501-1:2007+A1:2009, 3.1.6 3.15 organic content total amount of organic substances as part of a component
36、or a product related to the mass in cured and dried conditions Note 1 to entry: Will be declared by the system holder according to the formulation of the product in question and will be determined by calculation. It is given in percentage by mass in cured and dried condition. 3.16 worst case configu
37、ration of specified ETICS components for test purposes that leads to the most discriminating class or level of a certain characteristic which leads to results valid for a group of configurations with assumed equal or better performance Note 1 to entry: Characteristics can be e.g. impact resistance,
38、reaction to fire, etc. 4 Principle The reaction to fire classification (Euro classes) shall be determined in accordance with EN 13501-1, respecting the test conditions of the ETICS laid down in this standard. In order to evaluate the reaction to fire all kits of the design ETIC system as well as the
39、 individual components shall be considered. Test results may be also valid for the assessment of the reaction to fire of further design ETICS. Rules are given below. NOTE 1 A European reference fire scenario has not been laid down for facades. In some Member States, the classification of ETICS accor
40、ding to EN 135011 might not be sufficient for the use on facades. An additional assessment of ETICS according to national provisions (e.g. on the basis of large scale tests) might be necessary to comply with Member State regulations, until the existing European classification system has been complet
41、ed. NOTE 2 In some Member States the requirements might exist to demonstrate the behaviour of products with respect to continuous glowing combustion in the case of fire. Additional national assessments e.g. on the basis of national procedures to demonstrate this behaviour might be required until a E
42、uropean harmonized procedure will be available. 5 Instructions for mounting and fixing, field of application 5.1 General This clause gives instructions for mounting and fixing for reaction to fire testing of a kit and its single components. This clause includes the field of application of the test r
43、esults of the kits as well as of its single components. BS EN 16724:2015 EN 16724:2015 (E) 7 Base coats shall be grouped according to the binder type into inorganic (cement-calcium hydroxide, alkali silicate, etc.) and organic (silicon resin, synthetic resin, etc.) coats. Finishing coats shall be gr
44、ouped in the same way. For each group of base coats and finishing coats the product with the highest organic content shall be tested in combination with the adhesive having the highest organic content. If there are only differences in the organic content but no difference in the organic component it
45、self, the product with the highest organic content shall be tested. The test results are valid also for adhesives, base coats and finishing coats with equal or lower organic content. If adhesives, base coats or finishing coats include flame retardants, those components with the lowest amount of flam
46、e retardant shall be tested additionally. The key coat and the decorative coat may be neglected if the layer thickness of each coat is less than 200 m and the organic content is less than 5 %. NOTE The layer thickness may be calculated by the coverage. Key coat and decorative coat shall be considere
47、d for testing unless it can be neglected according to the rules mentioned in the paragraph before. The key coat and the decorative coat with the highest PCS-value (according to EN ISO 1716) shall be used for preparing the specimens. 5.2 Testing according to EN ISO 1182 (Non-combustibility test) 5.2.
48、1 General This test method is relevant for the classes A1 and A2. For classes A1 and A2 every substantial component (3.12) shall be tested. Mechanical fixing devices and ancillary materials which are not continuous but discrete components of an ETICS shall not be considered for testing and classific
49、ation regarding non-combustibility. NOTE Base coats, finishing coats and adhesives in accordance with the provisions of EC decision 96/603/EC (amended by decisions 2000/605/EC and 2003/424/EC) are considered to satisfy the requirements for performance class A1 without the need for testing. 5.2.2 Base coat and finishing coats The reaction to fire behaviour of base coats and finishing coats not falling under EC decision 96/603/EC (amended by decisions 2000/605/EC and 2003/424/EC) shall be tested by using the product with the highest amount of organic c
