1、BSI Standards PublicationBS ISO 603-17:2014Bonded abrasive products DimensionsPart 17: Spindle mounted wheels (ISO type52)BS ISO 603-17:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 603-17:2014.The UK participation in its preparation was entrusted to Tec
2、hnicalCommittee MTE/13, Grinding wheels, abrasive tools, paper andcloths, and powders.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its
3、 correctapplication. The British Standards Institution 2014. Published by BSI StandardsLimited 2014ISBN 978 0 580 75117 2ICS 25.100.70Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Str
4、ategy Committee on 31 July 2014.Amendments issued since publicationDate Text affectedBS ISO 603-17:2014 ISO 2014Bonded abrasive products Dimensions Part 17: Spindle mounted wheels (ISO type 52)Produits abrasifs agglomrs Dimensions Partie 17: Meules sur tige (ISO type 52)INTERNATIONAL STANDARDISO603-
5、17First edition2014-07-15Reference numberISO 603-17:2014(E)BS ISO 603-17:2014ISO 603-17:2014(E)ii ISO 2014 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2014All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by an
6、y means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Gen
7、eva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 603-17:2014ISO 603-17:2014(E) ISO 2014 All rights reserved iiiContents PageForeword iv1 Scope . 12 Normative references 13 Shapes and dimensions . 13.1 Wheel plain, Shape WPL . 13.2
8、Wheel concave end, Shape WCC . 43.3 Wheel round end, Shape WRE . 43.4 Wheel conical end, Shape WCE . 53.5 Wheel truncated cone end, Shape WTC . 63.6 Wheel conical round end, Shape WCR 63.7 Conical double taper, Shape CDT . 73.8 Conical round end, Shape CRE . 83.9 Conical truncated end, Shape CTE 93.
9、10 Wheel ogival end, Shape WOE . 93.11 Spherical, Shape SPH 103.12 Conical inverse cup, Shape CIC . 113.13 Profiled periphery tapered, Shape PPT 123.14 Conical inverse flat end, Shape CIF . 133.15 Conical inverse round end, Shape CIR . 143.16 Profiled periphery curved, Shape PPC . 153.17 Profiled pe
10、riphery pointed, Shape PPP. 153.18 Conical inverse dish, Shape CID . 163.19 Mushroom, Shape MSH . 174 Designation .185 Specifications 185.1 Material 185.2 Marking 18BS ISO 603-17:2014ISO 603-17:2014(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of natio
11、nal standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. Internati
12、onal organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended
13、 for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso
14、.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will
15、 be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressi
16、ons related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe committee responsible for this document is ISO/TC 29, Small tools, Subcommittee SC 5, Grindi
17、ng wheels and abrasives.ISO 603 consists of the following parts, under the general title Bonded abrasive products Dimensions: Part 1: Grinding wheels for external cylindrical grinding between centres Part 2: Grinding wheels for centreless external cylindrical grinding Part 3: Grinding wheels for int
18、ernal cylindrical grinding Part 4: Grinding wheels for surface grinding/peripheral grinding Part 5: Grinding wheels for surface grinding/face grinding Part 6: Grinding wheels for tool and tool room grinding Part 7: Grinding wheels for manually guided grinding Part 8: Grinding wheels for deburring an
19、d fettling/snagging Part 9: Grinding wheels for high-pressure grinding Part 10: Stones for honing and superfinishings Part 11: Hand finishing sticks Part 12: Grinding wheels for deburring and fettling on a straight grinder Part 13: Grinding wheels for deburring and fettling on a vertical grinder Par
20、t 14: Grinding wheels for deburring and fettling/snagging on an angle grinder Part 15: Grinding wheels for cutting-off on stationary or mobile cutting-off machines Part 16: Grinding wheels for cutting-off on hand-held power toolsiv ISO 2014 All rights reservedBS ISO 603-17:2014ISO 603-17:2014(E) Par
21、t 17: Spindle mounted wheels (ISO type 52) Part 18: Grinding wheels for flat glass edge grinding machines ISO 2014 All rights reserved vBS ISO 603-17:2014BS ISO 603-17:2014Bonded abrasive products Dimensions Part 17: Spindle mounted wheels (ISO type 52)1 ScopeThis part of ISO 603 specifies the curre
22、nt shapes, nominal dimensions and limit deviations, in millimetres, of Type 52: Spindle mounted wheels.These bonded abrasive products are intended to be used for hand-held grinding and manually guided or on hand-held power tools guided by hand.2 Normative referencesThe following documents, in whole
23、or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 525, Bonded abrasive products General
24、requirements3 Shapes and dimensionsNOTE 1 In all tables below, the “Designation” given in the first column is generated according to the following principle: Shape (= three letter code), D (mm), T (mm), and Sd(mm). For example, the designation for a spindle mounted wheel, shape WPL with D = 10 mm, T
25、 = 13 mm, and Sd= 6 mm the designation is “WPL 10 13 06”. As an exception, this rule can only be applied equivalently to 3.11, Table 11, because dimension T does not exist for the spherical shape.NOTE 2 In all tables below, the former code is given in the second column for information only.3.1 Wheel
26、 plain, Shape WPLSee Figure 1 and Table 1.INTERNATIONAL STANDARD ISO 603-17:2014(E) ISO 2014 All rights reserved 1BS ISO 603-17:2014ISO 603-17:2014(E)Dimensions in millimetresKey1 colletaL3 10.bSd= 3 and L2= 30 or Sd= 6 and L2= 40 or Sd= 8 and L2= 40.Figure 1 Wheel plain, Shape WPLTable 1 Wheel plai
27、n, Shape WPL, Sd= 3 mm and L2= 30 mm or Sd= 6 mm and L2= 40 mm or Sd= 8 mm and L2= 40 mmDimensions in millimetresDesignationFormer codeD TWPL 03 06 03 W14436WPL 03 10 03 W145 10WPL 03 13 03 W146 13WPL 05 06 03 W15256WPL 05 10 03 W153 10WPL 05 13 03 W154 13WPL 06 06 03 W16066WPL 06 10 03 WPL 06 10 06
28、W162 10WPL 06 13 03 WPL 06 13 06W163 13WPL 06 20 03 W164 20WPL 08 10 03 WPL 08 10 06W169810WPL 08 13 03 W170 13WPL 08 20 03 W171 20WPL 10 10 03 WPL 10 10 06W1751010WPL 10 13 03 WPL 10 13 06W176 13WPL 10 20 03 WPL 10 20 06W177 20WPL 10 25 03 WPL 10 25 06W178 25WPL 10 32 06 W179 322 ISO 2014 All right
29、s reservedBS ISO 603-17:2014ISO 603-17:2014(E)DesignationFormer codeD TWPL 13 03 03 WPL 13 03 06W182133WPL 13 06 03 WPL 13 06 06W183 6WPL 13 13 03 WPL 13 13 06W185 13WPL 13 20 03 WPL 13 20 06W186 20WPL 13 25 03 WPL 13 25 06W187 25WPL 13 40 06 W188 40WPL 16 20 03 WPL 16 20 06W1951620WPL 16 25 03 WPL
30、16 25 06W196 25WPL 16 50 06 W197 50WPL 20 06 03 WPL 20 06 06W201206WPL 20 10 03 WPL 20 10 06W202 10WPL 20 20 03 WPL 20 20 06W204 20WPL 20 25 06 W205 25WPL 20 32 06 W206 32WPL 20 38 06 W207 38WPL 20 50 06 W208 50WPL 25 03 03 WPL 25 03 06W215253WPL 25 06 03 WPL 25 06 06W216 6WPL 25 10 06 W217 10WPL 25
31、 13 06 W218 13WPL 25 20 06 W219 20WPL 25 25 06 W220 25WPL 25 32 06 WPL 25 32 08W221 32WPL 25 50 06 WPL 25 50 08W222 50WPL 32 06 06 W225326WPL 32 10 06 W226 10WPL 32 20 06 W228 20WPL 32 32 06 WPL 32 32 08W230 32WPL 32 50 06 W232 50WPL 38 06 06 W235386WPL 38 13 06 W236 13WPL 38 38 06 WPL 38 38 08W238
32、38Table 1 (continued) ISO 2014 All rights reserved 3BS ISO 603-17:2014ISO 603-17:2014(E)DesignationFormer codeD TWPL 40 20 06 WPL 40 20 08W237 40 20WPL 50 25 06 WPL 50 25 08W242 50 253.2 Wheel concave end, Shape WCCSee Figure 2 and Table 2.Dimensions in millimetresKey1 colletaL3 10.bSd= 3 and L2= 30
33、 or Sd= 6 and L2= 40.cR is specified by the manufacturer.Figure 2 Wheel concave end, Shape WCCTable 2 Wheel concave end, Shape WCC, Sd= 3 mm and L2= 30 mm or Sd= 6 mm and L2= 40 mmDimensions in millimetresDesignationFormer codeD TWCC 06 13 03 B135 6 13WCC 10 13 06 B1321013WCC 10 10 03 B133 10WCC 10
34、13 03 B132 13WCC 13 13 03 WCC 13 13 06B131 13 13WCC 20 30 06 A39 20 30WCC 25 25 06 A38 25 253.3 Wheel round end, Shape WRESee Figure 3 and Table 3.Table 1 (continued)4 ISO 2014 All rights reservedBS ISO 603-17:2014ISO 603-17:2014(E)Key1 colletaL3 10.bSd= 6 and L2= 40.Figure 3 Wheel round end, Shape
35、WRETable 3 Wheel round end, Shape WRE, Sd= 6 mm and L2= 40 mmDimensions in millimetresDesignationFormer codeD TWRE 06 20 06 A24 6 20WRE 25 25 06 A21 25 253.4 Wheel conical end, Shape WCESee Figure 4 and Table 4.Dimensions in millimetresKey1 colletaFor D 20 mm is = 60. For D 20 mm is = 90.bL3 10.cSd=
36、 3 and L2= 40 or Sd= 6 and L2= 40.d is specified by the manufacturer.Figure 4 Wheel conical end, Shape WCE ISO 2014 All rights reserved 5BS ISO 603-17:2014ISO 603-17:2014(E)Table 4 Wheel conical end, Shape WCE, Sd= 3 mm and L2= 30 mm or Sd= 6 mm and L2= 40 mmDimensions in millimetresDesignationForme
37、r codeD TWCE 06 10 03 B53610WCE 06 27 06 A15 27WCE 20 22 06 A142022WCE 20 63 06 A1 63WCE 28 28 06 A13 28 283.5 Wheel truncated cone end, Shape WTCSee Figure 5 and Table 5.Dimensions in millimetresKey1 colletaFor D 20 mm is = 60. For D 20 mm is = 90.bL3 10.cSd= 3 and L2= 30 or Sd= 6 and L2= 40.Figure
38、 5 Wheel truncated cone end, Shape WTCTable 5 Wheel truncated cone end, Shape WTC, Sd= 3 mm and L2= 30 mm or Sd= 6 mm and L2= 40 mmDimensions in millimetresDesignationFormer codeD TWTC 06 10 03 B53610WTC 06 27 06 A15 27WTC 20 22 06 A142022WTC 20 63 06 A1 63WTC 28 28 06 A13 28 283.6 Wheel conical rou
39、nd end, Shape WCRSee Figure 6 and Table 6.6 ISO 2014 All rights reservedBS ISO 603-17:2014ISO 603-17:2014(E)Dimensions in millimetresKey1 colletaL3 10.bSd= 3 and L2= 30 or Sd= 6 and L2= 40.cR is specified by the manufacturer.dT1is specified by the manufacturer.eT2is specified by the manufacturer.Fig
40、ure 6 Wheel conical round end, Shape WCRTable 6 Wheel conical round end, Shape WCR, Sd= 3 mm and L2= 30 mm or Sd= 6 mm and L2= 40 mmDimensions in millimetresDesignationFormer codeD TWCR 16 16 03 WCR 16 16 06B41 16 16WCR 20 30 06 A5 20 30WCR 32 32 06 A4 32 323.7 Conical double taper, Shape CDTSee Fig
41、ure 7 and Table 7. ISO 2014 All rights reserved 7BS ISO 603-17:2014ISO 603-17:2014(E)Dimensions in millimetresKey1 colletaL3 10.bSd= 3 and L2= 30 or Sd= 6 and L2= 40.cD is specified by the manufacturer.dT2is specified by the manufacturer.Figure 7 Conical double taper, Shape CDTTable 7 Conical double
42、 taper, Shape CDT, Sd= 3 mm and L2= 30 mm or Sd= 6 mm and L2= 40 mmDimensions in millimetresDesignationFormer codeD TCDT 11 20 03 CDT 11 20 06B51 11 203.8 Conical round end, Shape CRESee Figure 8 and Table 8.Dimensions in millimetresKey1 colletaR is specified by the manufacturer.bL3 10.cSd= 6 and L2
43、= 40.Figure 8 Conical round end, Shape CRE8 ISO 2014 All rights reservedBS ISO 603-17:2014ISO 603-17:2014(E)Table 8 Conical round end, Shape CRE, Sd= 6 mm and L2= 40 mmDimensions in millimetresDesignationFormer codeD TCRE 16 45 06 A3mini 16 45CRE 25 70 06 A3 25 703.9 Conical truncated end, Shape CTE
44、See Figure 9 and Table 9.Dimensions in millimetresKey1 colletaL3 10.bSd= 3 and L2= 30 or Sd= 6 and L2= 40.c is specified by the manufacturer.Figure 9 Conical truncated end, Shape CTETable 9 Conical truncated end, Shape CTE, Sd= 3 mm and L2= 30 mm or Sd= 6 mm and L2= 40 mmDimensions in millimetresDes
45、ignationFormer codeD TCTE 03 06 03 B9636CTE 03 10 03 B97 10CTE 06 06 03 B92 6 6CTE 13 16 03CTE 13 16 06B91 13 163.10 Wheel ogival end, Shape WOESee Figure 10 and Table 10. ISO 2014 All rights reserved 9BS ISO 603-17:2014ISO 603-17:2014(E)Dimensions in millimetresKey1 colletaR = 1 to 2,5 D.bL3 10.cSd
46、= 3 and L2= 30 or Sd= 6 and L2= 40.Figure 10 Wheel ogival end, Shape WOETable 10 Wheel ogival end, Shape WOE, Sd= 3 mm and L2= 30 mm or Sd= 6 mm and L2= 40 mmDimensions in millimetresDesignationFormer codeD TWOE 06 08 03 B43 6 8WOE 10 20 03 WOE 10 20 06B52 1020WOE 13 20 03 WOE 13 20 06B42 13WOE 20 3
47、2 06 A12 20 32WOE 22 50 06 A11 22 503.11 Spherical, Shape SPHSee Figure 11 and Table 11.10 ISO 2014 All rights reservedBS ISO 603-17:2014ISO 603-17:2014(E)Dimensions in millimetresKey1 colletaL3 10.bSd= 3 and L2= 30 or Sd= 6 and L2= 40.Figure 11 Spherical, Shape SPHTable 11 Spindle mounted wheels sp
48、herical shape, Shape SPH, Sd= 3 mm and L2= 30 mm or Sd= 6 mm and L2= 40 mmDimensions in millimetresDesignation Former code DSPH 03 03 B124 3SPH 05 03 B123 5SPH 13 03 SPH 13 06B121 13SPH 16 06 A26 16SPH 25 06 A25 253.12 Conical inverse cup, Shape CICSee Figure 12 and Table 12. ISO 2014 All rights res
49、erved 11BS ISO 603-17:2014ISO 603-17:2014(E)Dimensions in millimetresKey1 colletaL3 10.b = 10 to 16.cT1= 0,4 to 0,55 T.dSd= 3 and L2= 30 or Sd= 6 and L2= 40.eD1approximately 0,6 D.Figure 12 Conical inverse cup, Shape CICTable 12 Conical inverse cup, Shape CIC, Sd= 3 mm and L2= 30 mm or Sd= 6 mm and L2= 40 mmDimensions in millimetresDesignationFormer codeD TCIC 16 18 03 CIC 16 18 06B101 1618CIC 25 18 06 A32 25CIC 35 37 06
