1、DEUTSCHE NORM February 200( Cross recessed raised countersunk head drilling screws with tapping screw thread - I EN IS0 15483 (IS0 15483 : 1999) English version of DIN EN IS0 15483 ICs 21.060.10 Linsensenk-Bohrschrauben mit Kreuzschlitz mit Blechschraubengewinde (IS0 15483 : 1999) This standard, tog
2、ether with DIN EN IS0 10666, DIN EN IS0 15480, DIN EN IS0 15481, and DIN EN IS0 15482, February 2000 editions, supersedes DIN 7504, September 1995 edition. European Standard EN IS0 15483 : 1999 has the status of a DIN Standard. A comma is used as the decimal marker. National foreword This standard h
3、as been published in accordance with a decision taken by CEN/TC 185 to adopt, without alteration, International Standard IS0 15483 as a European Standard. The responsible German body involved in its preparation was the Normenausschuss Mechanische Ver- bindungse/emenfe (Fasteners Standards Committee)
4、. The DIN Standards corresponding to the International Standards referred to in clause 2 of the EN are as follows: IS0 Standard DIN Standard IS0 1478 IS0 3269 IS0 4042 IS0 7721 DIN EN 27721 IS0 10666 DIN EN IS0 1478 DIN EN IS0 3269*) DIN EN IS0 4042 IS0 4759-1 DIN EN IS0 4759-1 *) DIN EN IS0 10666 A
5、mendments DIN 7504, September 1995 edition, has been superseded by the specifications of EN IS0 15483, which is identical to IS0 15483. Previo us edit ions DIN 7504: 1982-1 1, 1992-02, 1995-09. National Annex NA Standards referred to (and not included in Normative references and Annex ZA) DIN EN 277
6、21 DIN EN IS0 1478 DIN EN IS0 3269 DIN EN IS0 4042 DIN EN IS0 4759-1 DIN EN IS0 10666 Countersunk head screws - Head configuration and gauging (IS0 7721 : 1983) Tapping screw threads (IS0 1478 : 1999) Fasteners - Acceptance inspection (ISO/DIS 3269 : 1998)*) Fasteners - Electroplated coatings (IS0 4
7、042 : 1999) Tolerances for fasteners - Part 1 : Bolts, screws, studs and nuts - Product grades A, B and C (ISO/DIS 4759-1 : 1997)*) Drilling screws with tapping screw thread - Mechanical and functional properties (IS0 10666 : 1999) *) At present at draft stage. EN comprises 5 pages. I Q No pari of t
8、his standard may be reproduced without the prior permission of Ref. No. DIN EN IS0 15483 : 2000-C DIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany, has the exclusive right of sale for German Standards (DIN-Normen). English price group 07 Sales No. 1107 07.00
9、EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN IS0 15483 August 1999 ICs 21.060.1 O English version Cross recessed raised countersunk head drilling screws with tapping screw thread (IS0 15483 : 1999) Vis autoperceuses tte fraise bom- be empreinte cruciforme, avec filetage de vis tle (IS0 15483
10、 : 1999) Linsensenk-Bohrschrauben mit Kreuzschlitz mit Blechschrauben- gewinde (IS0 15483 : 1999) This European Standard was approved by CEN on 1999-07-1 6. CEN members are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving this European Standard the s
11、tatus of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national stand- ards may be obtained on application to the Central Secretariat or to any CEN member. The European Standards exist in three official versions (English, French, German).
12、 A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, the Czech Republic, Denmark, Fi
13、nland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, the Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, and the United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36
14、, B-1050 Brussels O 1999. CEN - All rights of exploitation in any form and by any means reserved worldwide for CEN national members. Ref. No. EN IS0 15483 : 1999 E Page 2 EN IS0 15483 : 1999 Foreword International Standard IS0 15483 : 1999 which was prepared by ISO/TC 2 Fasteners of the Internationa
15、l Organization for Standardization, has been adopted by Technical Committee CEN/TC 185 Threaded and non-threaded mechanical fasteners and acces- sories, the Secretariat of which is held by DIN, as a European Standard. This European Standard shall be given the status of a national standard, either by
16、 publication of an identical text or by endorsement, and conflicting national standards withdrawn, by February 2000 at the latest. In accordance with the CENKENELEC Internal Regulations, the national standards organizations of the follow- ing countries are bound to implement this European Standard:
17、Austria, Belgium, the Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, the Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, and the United Kingdom. Cross recessed raised countersunk head drilling screws with tapping screw thread, Endorsement n
18、otice The text of the International Standard IS0 15483 : 1999 was approved by CEN as a European Standard without any modification. NOTE: Normative references to international publications are listed in Annex ZA (normative). 1 Scope This International Standard specifies the characteristics of cross r
19、ecessed raised countersunk head drilling screws with tapping screw threads from ST2,9 up to and including ST6,3. 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this International Standard. For dated referenc
20、es, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated refere
21、nces, the latest edition of the normative document referred to applies. Members of IS0 and IEC maintain registers of currently valid International Standards. IS0 1478:1999, Tapping screws thread. IS0 3269:-), Fasteners - Acceptance inspection. IS0 4042: 1999, Fasteners - Electroplated coatings. IS0
22、4757:1983, Cross recesses for screws. IS0 4759-1 :-2), Tolerances for fasteners - Part 1: Bolts, screws, studs and nuts - Product grades A, B and C. IS0 7721 :1983, Countersunk head screws - Head configuration and gauging. IS0 10666:i 999, Drilling screws with tapping screw thread - Mechanical and f
23、unctional properties. l) To be published. (Revision of IS0 3269:1988) 2, To be published. (Revision of IS0 4759-1:1978) Page 3 EN IS0 15483 : 1999 3 Dimensions See Figure 1 and Table 1. Cross recess Type H Type Page 4 EN IS0 15483 : 1999 theoretical max. d, actual max. min. Table 1 - Dimensions Dime
24、nsions in millimetres 63 82 9,4 10,4 11,5 12,6 5,5 7,3 8,4 9,3 10,3 11,3 52 63 8,O 69 939 10,9 Thread ST2,9 ST3,5 ST4,2 ST4,8 ST5,5 ST6,3 1 !1 13 1,4 15 1,8 18 Type H 111 ref. Penetration max. 3,4 43 52 5,4 67 723 2,2 2.75 3.2 3.4 3.45 4.0 t = I 0,7 I 0,8 I 1 I 1,2 I 1,3 I 1,4 Type z 111 ref. Penetr
25、ation max. Cross Recess No recess 3,3 43 52 5.6 6,6 72 2.1 2,70 3.10 3,35 3,40 3,85 2 min. 3 1.8 2,25 2.65 2,90 2,95 3,40 Drilling range from (sheet or plate thickness)d to min. I 1,8 I 2,25 I 2,7 I 2.9 I 2,95 I 33 0.7 0,7 1.75 1,75 1,75 2 1.9 2,25 3 44 5,25 6 I nom. I min. I max. Ge min. 50 48,75 5
26、1,25 39.5 39 38 a P is the pitch of the thread. U is the distance from the underside of the head to the first major diameter of the thread. See IS0 7721. In order to determine the nominal length I it may be necessary to add an air gap (if present) to the individual sheet or plate thicknesses. I, is
27、the distance from the underside of the head to the last major diameter of the thread. e Page 5 EN IS0 15483 : 1999 International Standard 4 Specifications and reference International Standards See Table 2. Table 2 - Specifications and reference International Standards Steel IS0 10666 Material Accept
28、ability Acceptance procedure is covered in IS0 3269. I Thread International Standard I IS0 1478 I Cross recesses International Standard I IS0 4757 Mechanical and functional International Standard properties IS0 10666 Tolerances I A Product grade International Standard I IS0 4759-1 Finish Plain Requi
29、rements for electroplating are covered in IS0 4042. 5 Designation EXAMPLE A cross recessed raised countersunk head drilling screw with thread ST3,5, nominal length I = 16 mm and recess type Z is designated as follows: Drilling screw IS0 15483 - ST33 x 16 - Z Annex ZA (normative) Normative references
30、 to international publications with their relevant European publications This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For da
31、ted references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. Publication Year Title EN Year IS0 1478 1983 Tapping screws thread EN IS0 1478 1994 IS0 4042 1999 Fasteners - Electroplated coatings EN IS0 4042 1999 IS0 7721 1983 Countersunk head screws - Head configuration and EN 27721 1991 gauging
