1、April 2010 Translation by DIN-Sprachendienst.English price group 12No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS
2、21.060.10!$aZZ“1625555www.din.deDDIN EN ISO 3506-3Mechanical properties of corrosion-resistant stainless steel fasteners Part 3: Set screws and similar fasteners not under tensile stress(ISO 3506-3:2009)English translation of DIN EN ISO 3506-3:2010-04Mechanische Eigenschaften von Verbindungselemente
3、n aus nichtrostenden Sthlen Teil 3: Gewindestifte und hnliche nicht auf Zug beanspruchte Verbindungselemente(ISO 3506-3:2009)Englische bersetzung von DIN EN ISO 3506-3:2010-04Caractristiques mcaniques des lments de fixation en acier inoxydable rsistant lacorrosion Partie 3: Vis sans tte et lments de
4、 fixation similaires non soumis des contraintes detraction (ISO 3506-3:2009)Traduction anglaise de DIN EN ISO 3506-3:2010-04SupersedesDIN EN ISO 3506-3:1998-03www.beuth.deIn case of doubt, the German-language original shall be considered authoritative.Document comprises 25 pages03.10 DIN EN ISO 3506
5、-3:2010-04 2 A comma is used as the decimal marker. National foreword This standard has been prepared by Technical Committee ISO/TC 2 “Fasteners” in collaboration with Technical Committee CEN/TC 185 “Fasteners” (Secretariat: DIN, Germany). The responsible German body involved in its preparation was
6、the Normenausschuss Mechanische Verbin-dungselemente (Fasteners Standards Committee), Working Committee NA 067-02-03 AA Mechanische Eigenschaften fr Schrauben und Muttern aus nichtrostendem und temperaturbestndigem Stahl. The DIN Standards corresponding to the International Standards referred to in
7、this document are as follows: ISO 68-1 DIN ISO 68-1 ISO 261 DIN ISO 261 ISO 262 DIN ISO 262 ISO 898-5 DIN EN ISO 898-5 ISO 965-3 DIN ISO 965-3 ISO 3506- DIN EN ISO 3506- ISO 3651-1 DIN EN ISO 3651-1 ISO 3651-2 DIN EN ISO 3651-2 ISO 6506-1 DIN EN ISO 6506-1 ISO 6507-1 DIN EN ISO 6507-1 ISO 6508-1 DIN
8、 EN ISO 6508-1 ISO 16048 DIN EN ISO 16048 ISO 16426 DIN EN ISO 16426 Amendments This standard differs from DIN EN ISO 3506-3:1998-03 as follows: a) The temperature range has been changed from between 15 C and 25 C to between 10 C and 35 C. b) Clause 3 “Designation, marking and finish” has been given
9、 in more detail. c) In subclause 3.3 “Finish”, symbol “P” has been added for marking passivated set screws and similar fasteners. d) In Table 2, the copper content for steel grade A4 has been increased from 1 % to 4 %. Previous editions DIN 267-11: 1968-05, 1977-02, 1980-01 DIN ISO 3506: 1992-12 DIN
10、 EN ISO 3506-3: 1998-03 1 1DIN EN ISO 3506-3:2010-04 3 National Annex NA (informative) Bibliography DIN EN ISO 898-5, Mechanical properties of fasteners made of carbon steel and alloy steel Part 5: Set screws and similar fasteners not under tensile stress DIN EN ISO 3506-1, Mechanical properties of
11、corrosion-resistant stainless-steel fasteners Part 1: Bolts, screws and studs DIN EN ISO 3651-1, Determination of resistance to intergranular corrosion of stainless steels Part 1: Austenitic and ferritic-austenitic (duplex) stainless steels Corrosion test in nitric acid medium by measurement of loss
12、 in mass (Huey test) DIN EN ISO 3651-2, Determination of resistance to intergranular corrosion of stainless steels Part 2: Ferritic, austenitic and ferritic-austenitic (duplex) stainless steels Corrosion test in media containing sulfuric acid DIN EN ISO 6506-1, Metallic materials Brinell hardness te
13、st Part 1: Test method DIN EN ISO 6507-1, Metallic materials Vickers hardness test Part 1: Test method DIN EN ISO 6508-1, Metallic materials Rockwell hardness test Part 1: Test method (scales A, B, C, D, E, F, G, H, K, N, T) DIN EN ISO 16048, Passivation of corrosion-resistant stainless-steel fasten
14、ers DIN EN ISO 16426, Fasteners Quality assurance system DIN ISO 68-1, ISO general purpose metric screw threads Basic profile Part 1: Metric screw threads DIN ISO 261, ISO general purpose metric screw threads General plan DIN ISO 262, ISO general purpose metric screw threads Selected sizes for screw
15、s, bolts and nuts DIN ISO 965-3, ISO general purpose metric screw threads Tolerances Part 3: Deviations for constructional threads DIN EN ISO 3506-3:2010-04 4 This page is intentionally blank EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 3506-3 November 2009 ICS 21.060.10 Supersedes EN IS
16、O 3506-3:1997English Version Mechanical properties of corrosion-resistant stainless steel fasteners - Part 3: Set screws and similar fasteners not under tensile stress (ISO 3506-3:2009) Caractristiques mcaniques des lments de fixation en acier inoxydable rsistant la corrosion - Partie 3: Vis sans tt
17、e et lments de fixation similaires non soumis des contraintes de traction (ISO 3506-3:2009) Mechanische Eigenschaften von Verbindungselementen aus nichtrostenden Sthlen - Teil 3: Gewindestifte und hnliche nicht auf Zug beanspruchte Verbindungselemente (ISO 3506-3:2009) This European Standard was app
18、roved by CEN on 24 October 2009. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nation
19、al standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and no
20、tified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg,
21、Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of e
22、xploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 3506-3:2009: EContents DIN EN ISO 3506-3:2010-04 EN ISO 3506-3:2009 (E) 2 Page Foreword .3 Introduction.4 1 Scope5 2 Normative references5 3 Designation, marking and finish6 3.1 Designation 6 3.2 Ma
23、rking.7 3.3 Finish 8 4 Chemical composition 8 5 Mechanical properties.9 5.1 General .9 5.2 Proof torque of hexagon socket set screws.9 5.3 Hardness 10 6 Test methods .10 6.1 Proof torque test for hexagon socket set screws10 6.2 Hardness test HB, HRB or HV for set screws.11 Annex A (normative) Descri
24、ption of the groups and grades of stainless steels .12 Annex B (informative) Austenitic stainless steel composition specifications.15 Annex C (informative) Austenitic stainless steels for cold heading and extruding.17 Annex D (informative) Time-temperature diagram of intergranular corrosion in auste
25、nitic stainless steels, grade A2 (18/8 steels).19 Annex E (informative) Magnetic properties for austenitic stainless steels 20 Bibliography21 Foreword collaboration with Technical Committee CEN/TC 185 “Fasteners”, the secretariat of which is held by DIN. This European Standard shall be given the sta
26、tus of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2010, and conflicting national standards shall be withdrawn at the latest by May 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of
27、 patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 3506-3:1997. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this
28、European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the Un
29、ited Kingdom. Endorsement notice The text of ISO 3506-3:2009 has been approved by CEN as a EN ISO 3506-3:2009 without any modification. DIN EN ISO 3506-3:2010-04 EN ISO 3506-3:2009 (E) 3 This document (EN ISO 3506-3:2009) has been prepared by Technical Committee ISO/TC 2 “Fasteners” in Introduction
30、In the preparation of this part of ISO 3506, special attention has been given to the fundamentally different property characteristics of the stainless steel fastener grades compared with those of carbon steel and low-alloy steel fasteners. Austenitic stainless steels are strengthened only by cold wo
31、rking and consequently the components do not have as homogeneous local material properties as hardened and tempered parts. These special features have been recognized in the elaboration of the hardness classes and the test procedures for mechanical properties. DIN EN ISO 3506-3:2010-04 EN ISO 3506-3
32、:2009 (E) 4 1 Scope This part of ISO 3506 specifies the mechanical properties of set screws and similar fasteners not under tensile stress made of austenitic stainless steel, when tested over an ambient temperature range of 10 C to 35 C. Properties vary at higher or lower temperatures. This part of
33、ISO 3506 applies to set screws and similar fasteners: with nominal thread diameter 1,6 mm u d u 24 mm; of triangular ISO metric threads with diameters and pitches in accordance with ISO 68-1, ISO 261 and ISO 262; of any shape. It does not apply to screws with special properties, such as weldability.
34、 NOTE The designation system of this part of ISO 3506 can be used for sizes outside the limits given in this clause (e.g. d 24 mm), provided that all applicable mechanical and physical requirements of the hardness classes are met. This part of ISO 3506 does not define corrosion or oxidation resistan
35、ce in particular environments. The aim of this part of ISO 3506 is the classification of corrosion-resistant stainless steel fasteners into hardness classes. Corrosion and oxidation performances and mechanical properties for use at elevated or sub-zero temperatures can be agreed on between the user
36、and the manufacturer in each particular case. Annex D shows how the risk of intergranular corrosion at elevated temperatures depends on the carbon content. All austenitic stainless steel fasteners are normally non-magnetic in the annealed condition; after cold working, some magnetic properties can b
37、e evident (see Annex E). 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. I
38、SO 68-1, ISO general purpose screw threads Basic profile Part 1: Metric screw threads ISO 261, ISO general purpose metric screw threads General plan DIN EN ISO 3506-3:2010-04 EN ISO 3506-3:2009 (E) 5 ISO 262, ISO general purpose metric screw threads Selected sizes for screws, bolts and nuts ISO 898-
39、5, Mechanical properties of fasteners made of carbon steel and alloy steel Part 5: Set screws and similar threaded fasteners not under tensile stresses ISO 3651-1, Determination of resistance to intergranular corrosion of stainless steels Part 1: Austenitic and ferritic-austenitic (duplex) stainless
40、 steels Corrosion test in nitric acid medium by measurement of loss in mass (Huey test) ISO 3651-2, Determination of resistance to intergranular corrosion of stainless steels Part 2: Ferritic, austenitic and ferritic-austenitic (duplex) stainless steels Corrosion test in media containing sulfuric ac
41、id ISO 6506-1, Metallic materials Brinell hardness test Part 1: Test method ISO 6507-1, Metallic materials Vickers hardness test Part 1: Test method ISO 6508-1, Metallic materials Rockwell hardness test Part 1: Test method (scales A, B, C, D, E, F, G, H, K, N, T) ISO 16048, Passivation of corrosion-
42、resistant stainless-steel fasteners ISO 16426, Fasteners Quality assurance system 3 Designation, marking and finish 3.1 Designation The designation system for stainless steel grades and hardness classes for set screws and similar fasteners is given in Figure 1. The designation of the material consis
43、ts of two blocks, which are separated by a hyphen. The first block designates the steel grade and the second block, the hardness class. The designation of the steel grade (first block) consists of the letter A for austenitic steel, which indicates the group of steel and a digit, which indicates a ra
44、nge of chemical compositions within this steel group (see Table 2). The designation of the hardness class (second block) consists of two digits representing 1/10 of the minimum Vickers hardness and the letter H, referring to hardness (see Table 1). Table 1 Designations of hardness classes in relatio
45、n to Vickers hardness Hardness class 12H 21H Vickers hardness, HV min. 125 210 EXAMPLE A1-12H indicates: austenitic steel, soft, minimum hardness 125 HV. DIN EN ISO 3506-3:2010-04 EN ISO 3506-3:2009 (E) 6 aThe steel groups and steel grades classified in Figure 1 are described in Annex A and specifie
46、d by the chemical composition given in Table 2. bLow-carbon austenitic stainless steels with carbon content not exceeding 0,03 % may additionally be marked with an “L”. EXAMPLE A4L-21H cSet screws and similar fasteners passivated in accordance with ISO 16048 may additionally be marked with a “P”. EX
47、AMPLE A4-21HP Figure 1 Designation system for stainless steel grades and hardness classes for set screws and similar fasteners 3.2 Marking 3.2.1 General Marking of set screws and similar fasteners is not mandatory. When set screws and similar fasteners manufactured to the requirements of this part o
48、f ISO 3506 are designated and marked, they shall be designated in accordance with the designation system described in 3.1 and marked in accordance with 3.2.2 and 3.2.3. However, the designation system described in 3.1 and the provisions for marking according to 3.2.3 shall be used only if all releva
49、nt requirements of this part of ISO 3506 are met. 3.2.2 Manufacturers identification mark A manufacturers identification mark shall be included during the manufacturing process on all set screws and similar fasteners which are marked with a hardness class symbol, provided this is possible for technical reasons. Manufacturers identification marking is also recommended on set screws and similar fasteners which are not marked with a hardness cla
