1、A-A-55103 m 999997q 0119708 658 m I INCH-POUND I A-A-55 1 O 3 8 December 1992 COMMERCIAL ITEM DESCRIPTION I OVERSHOES, RADIOACTIVE CONTAMINANTS, PROTECTIVE The General Services Administration has authorized the use of this Commercial Item Description in preference to MIL-0-82246. Abstract. This docu
2、ment covers low unsupported molded overshoes of one type and in the designs specified herein. The overshoes are intended for protection of personnel in the presence of low level radioactive contaminants. 0 Salient Characteristics. The overshoes shall be constructed as an unlined unit on the contract
3、ors mold to provide proper fit for the related sizes and shapes of mens work shoes. The overshoes may be of a “storm“ or “sandal“ design as shown in Figure 1. They shall consist of an upper, sole, and heel. The tread pattern shall be a continuous grid type and shall not be subject to loss of pieces
4、in wear. The tread shall provide good traction. Figure 1 is furnished for information purposes only. To the extent of any inconsistencies between the written description and the figure, the description shall control. I Beneficial comments (recommendations, additions, deletions) and any pertinent dat
5、a which may be of use in improving this document should be addressed to: Defense Personnel Support Center, Clothing and Textiles Directorate, Attn: DPSC-FSSD, 2800 South 20th Street, Philadelphia, PA 19101-8419, by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at t
6、he end of this document or by letter. AMSC N/A DISTRIBUTION STATEMENT A. 0 FSC 8430 Approved for public release; distribution is unlimited. , Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55103 9999974 O119709 594 A-A- 5 5 1 O 3 The overshoe sh
7、all be cured and treated to eliminate tackiness and have a smooth finish. All mold flashings shall be trimmed and all inside corners rounded and made smooth. The yellow rubber compound for the patched area shall be molded simultaneously with the overshoe. Materials. 4 1 Rubber compound. The compound
8、 shall be made from virgin natural rubber, synthetic rubber or a combination of both. The compound shall meet the physical properties when tested as specified in Testinq of rubber compound, Table II-Tests. i Color. The color of the rubber compound forming the vamp, sole, instep, and heel shall be bl
9、ack. There shall be two yellow identification patch areas on each overshoe, one in the toe area covering 2 to 5 square inches and the other on rear quarter covering 15 to 20 square inches (see Figure 1). The yellow shall approximate Shade 13655 of FED-STD-595. Thickness. The thickness of the sole an
10、d heel excluding tread shall be a minimum of 0.100 inch. The thickness of the sole and heel including tread shall be a minimum of 0.135 inch. The minimum thickness of the upper shall be 0.030 inch except the reinforced portions shall be a minimum of 0.0375 inch. Sizes. The overshoes shall be in the
11、following sizes to accommodate the related size of shoe. Size Related shoe size Small 6 to 7-1/2 Medium 8 to 9 Large 9-1/2 to 11 Extra Large 11-1/2 to 13 NOTE: Sizes. Small, Medium, Large, Extra-Large may be abbreviated as SM, MED, LG, XLG. Markinq. The size and contractors name shall be molded on t
12、he outsole in the shank area with characters not less than 1/4 inch high. “Left“ and “right“ designation may be applied. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55103 9999974 0119710 206 A-A-55 1 O 3 e 8 I J Workmanship. After completio
13、n, the finished overshoes shall conform to the quality established by this description. Occurrence of defects shall not exceed the applicable acceptable quality levels. Product Demonstration Model. When required, offerers shall submit samples of their intended production. The Product Demonstration M
14、odel will consist of units independently developed. Product Demonstration Models will be analyzed and evaluated by the government. Evaluation criteria and basis for award are contained in the solicitation. Product Demonstration Models will be retained by the government. One (i) Product Demonstration
15、 Model approved by DPSC under the resultant contract . will serve as a manufacturing standard for the corresponding production items delivered under this contract. Offerers are advised that the Product Demonstration Model does not relieve the successful offerer of his responsibility to perform in ac
16、cordance with the Commercial Item Description specified above. Quality Assurance Certification. The contractor shall certify that the product offered meets the salient characteristics and all other requirements listed in this document and that the product conforms to the producers own drawings, spec
17、ifications, standards and quality assurance practices. The government reserves the right to require proof of such conformance prior to the first delivery and thereafter as may be otherwise provided for, under the provisions of the contract. Reliance on contractor QA systems shall not relieve the con
18、tractor of the responsibility of ensuring that all products or supplies submitted to the government for acceptance comply with all requirements of the contract. Testinq of rubber compounds. Unless otherwise specified, the tests shown in Table II shall be conducted in accordance with FED-STD-601. The
19、 physical values specified in Section 3 shall be applicable to the lot average. A lot shall consist of the amount of rubber compounded in a day. The sample unit for testing shall be a representative composite taken from a lot. Two specimens 6 by 6 inches shall be prepared from the composite for each
20、 of the prescribed tests. The specimens for the abrasion index and hardness tests shall be 0.250 inch thick and 0.075 inch thick for the other tests. The lot shall be unacceptable if two units fail any of prescribed tests. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted withou
21、t license from IHS-,-,-A-A-55103 m 9999974 OLL97L1 142 m A-A-55 103 Table II - Tests Characteristic Tensile stress: L/ 200 percent 400 percent 600 percent Tensile strength: Initial After aging Elongation: Initial After aging Hardness Abrasive index: Initial After aging Reference Requirement 200 psi
22、(minimum) 650 psi. (minimum) 1500 psi (minimum) 2000 psi (minimum) 30 percent(maximum 700 percent(minimum 30 percent(maximum 50 (25) 35 (minimum) 35 (minimum) Test method 4131 4131 4131 4111 4111, 7221 4121 4121, 7221 3021 ASTM Method D-1630 ASTM Method D-1630 7221 - i/ The modulus curve shall be ca
23、rried to the break point. Examination. Overshoe lots shall be inspected in accordance with “Sampling Procedures and Tables for Inspection by Attributes“, ANSI/ASQC 21.4, published by the American Society for Quality Control. Visual Examination. The inspection level for visual examination shall be II
24、 and the AQL shall be 2.5 for major and total of 6.5 major and minor combined expressed in terms of defects per hundred units. The sample unit shall be one overshoe and the selection shall be by pairs. For pairing examination, the pair shall be examined together. Defects The overshoes shall be exami
25、ned for the following defects: Not mated; not a right and left of an identical size; design and construction not asspecified; identification color patch missing; finish not smooth or poor or uneven molding; not of uniform color; tread pattern not continuous grid type; incomplete trimming of flashing
26、; marking missing; incorrect, illegible, or not located as specified; or any evidence of insecure bonding. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55103 W 999997i1 0119712 089 A-A-55 103 Thickness Examination. The finished overshoes sha
27、ll conform to the measurements specified herein. The sample unit shall be S-3 and the AQL shall be 1.5 expressed in terms of defects per hundred units. Packaqinq Examination. The fully packaged shipping containers shall be examined in accordance with defects listed below. The lot size shall be the n
28、umber of shipping containers in the inspection lot. The inspection level shall be S-2 and AQL shall be 1.5 expressed in terms of defects per hundred units. Examination Defect Marking (exterior) Materials Workmanship Content Omitted, incorrect, illegible, of improper size, location, sequence or metho
29、d of application. Any component missing or not as Any component damaged. specified. Inadequate application of components, such as: Incomplete closure of container flaps, loose strapping, Bulging or distortion of containers. Number of items per container is more or less than specified. Packaqinq. Pac
30、kaqinq. Each pair of mated overshoes of one size and design only, shall be placed heel to toe with the uppers facing each other. Each pair of overshoes shall be bound with an elastic band, or cotton tape or twine. Packaqinq. Sixty pairs of overshoes shall be placed into a fiberboard box conforming t
31、o RSC-L, grade 275 of PPP-B-636. The box shall be closed in accordance with the appendix of PPP-636. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55103 9999974 OLL97L3 TL5 A-A-55 1 O 3 Palletization. in accordance with load type Ia of MIL-ST
32、D-147. Each load shall be bonded with primary and secondary straps in accordance with bonding means C and D or film bonding means F or G. pattern shall be in accordance with the appendix of MIL-STD-147. Boxes shall be palletized on a 4-way entry pallet Pallet Markinq. Marking shall be in accordance
33、with MIL-STD-129. Requlatory Requirements. The offeror/contractor is encouraged to use recovered materials in accordance with Public Law 94-580 to the maximum extent practicable. I 4 Source of Governnent Documents. Copies of Military and Federal documents are available from: Standardization Document
34、s Order Desk Bldg. 4D 700 Robbins Avenue Philadelphia, PA 19111-5094 Sources of Nonuovernment Documents. O ANSI/ASQC 21.4 - Sampling Procedures and Tables For Inspection By Attributes (Applications for copies should be addressed to American National Standards Institute, 1430 Broadway, New York, NY 1
35、0018- 3308. ) (Applications for copies should be addressed to American Society For Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) Custodians: Navy -NU Air Force -11 Review Activities: Navy - SH Air Force -99 User Activities: Navy - AS, OS 6 Civil Agency Coordinating Act ivi ty : G
36、SA - FSS Preparing Activity: DLA - CT Project No.8430-0412 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-e z l A-A-55103 m 9999974 0119714 951 m A-A-5 5 1 O 3 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
