1、Beneficial comments recommendations, additions, deletions, clarifications, etc., and any data which may improvethis document should be addressed to: Defense Supply Center, Columbus, ATTN: DSCC-VAT, Post Office Box3990, Columbus, OH 43213-1199, or telephone (614) 692-0562, or facsimile (FAX) (614) 69
2、3-1644.AMSC N/A FSC 5915DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.INCH-POUNDA-A-55170BSeptember 17, 2001SUPERSEDINGA-A-55160AApril 29, 1994COMMERCIAL ITEM DESCRIPTIONFILTER, RADIO FREQUENCY INTERFERENCEThe General Services Administration has authorized the use
3、of thiscommercial item description (CID) for all federal agencies as areplacement for Federal Specification W-F-2190/10.1. SCOPE. This CID covers the general requirements for radio frequency interference (RFI) suppression power linefilters. These filters consist of capacitors and inductors used in c
4、ombination with each other and are provided withresistors as a safety feature. Filters covered by this CID are intended for commercial/industrial applications andshould not be used in military systems needing stringent environmental and electrical requirements.2. CLASSIFICATION. This CID uses a clas
5、sification system which is included in the Part Identification Number(PIN) as shown in the following example (see 7.1).AA55170 -01CID number Dash number3. SALIENT CHARACTERISTICS.3.1 Interface and physical dimensions. Filters supplied to this CID shall be as specified herein (see figures 1 and 2).3.
6、2. Voltage rating. The voltage rating shall be 120 V ac at 60 Hz; 250 V ac at 50 Hz.3.3 Operating frequency. The operating frequency shall be 50/60 Hz.3.4 Current rating. The current rating shall be as specified in table I.3.5 Operating ambient temperature range. The operating ambient temperature ra
7、nge shall be -10G01C to +40G01C atrated current.3.6 Maximum leakage current, line-to-ground. The maximum leakage current, line-to-ground, shall be 0.5 mA at120 V ac, 60 Hz; 1.0 mA at 250 V ac, 50 Hz.3.7 Hipot rating (1 minute). The hipot rating shall be 2,250 V dc line-to-ground; 1,450 V dc line-to-
8、line.3.8 Insertion loss. Insertion loss is given for line-to-ground in a 50-ohm circuit. Values shall be as specified in table I.3.9 Electrical schematic. The electrical schematic shall be as specified on figure 1.3.10 Marking. Filters supplied to this CID shall be marked with the manufacturers (MFR
9、s) standard commercialPIN.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55170B2TABLE I. Current rating and insertion loss.Minimum insertion loss (dB)Line-to-ground in 50 -ohm circuitFrequency (MHz)PINAA55170-Current rating Electricalschematic.1
10、5.5 1 5 103001 10 A A 5446065656002 20 A B 54460656560FIGURE 1. Electrical schematic.Case style AFIGURE 2. Case configuration and dimensions.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55170B3Case style BA(max)B(max)C(max)DG02.015/G02.38E(max
11、)PINAA55170-Inch mm Inch mm Inch mm Inch mm Inch mmCasestyle01 3.96 100.6 2.07 52.6 1.53 38.9 2.938 74.63 3.35 85.1 A02 5.34 135.6 3.37 85.6 1 53 38.9 3.750 95.25 4.20 106.7 BNOTES:1. Dimensions are in inches.2. Metric equivalents are given for general information only.3. Terminals: No. 8-32 (five).
12、4. Mounting holes: (Two) .188 inch (4.78 mm) diameter.5. Mounting slots: (Four) .250 inch (6.35 mm) x .156 inch (3.96 mm).6. Metric equivalents are in parentheses.FIGURE 2. Case configuration and dimensions - Continued.Provided by IHSNot for ResaleNo reproduction or networking permitted without lice
13、nse from IHS-,-,-A-A-55170B44. REGULATORY REQUIREMENTS. The offeror/contractor is encouraged to use recovered materials to themaximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR).5. PRODUCT CONFORMANCE PROVISIONS5.1 Product conformance. The prod
14、ucts provided shall meet the salient characteristics of this CID, conform to theproducers own drawings, specifications, standards, and quality assurance practices, and be the same productoffered for sale in the commercial market. The Government reserves the right to require proof of such conformance
15、6. PACKAGING. Preservation, packing, and marking shall be as specified in the contract or order.7. NOTES.7.1 PIN. The PIN should be used for Government purposes to buy commercial products to this CID. See section 2for PIN format example.7.2 Commercial and Government Entity (CAGE) code. For ordering
16、 purposes, inventory control, and submission ofthese filters to DSCC under the Military Parts control Advisory Group (MPCAG) evaluation program, CAGE code58536 should be used.7.3 Source of documents. This section is not applicable to this CID.7.4 Ordering data. The contract or order should specify t
17、he following:a. CID document number, revision, and CID PIN.b. Product conformance provisions.c. Packaging requirements.7.5 Commercial products. As part of the market analysis and research effort, this CID was coordinated with thefollowing manufacturers of commercial products. At the time of CID prep
18、aration and coordination, thesemanufacturers were known to have commercial products that would meet the requirements of this CID. (NOTE:This information should not be considered as a list of approved manufacturers or be used to restrict procurement toonly the manufacturers shown.)MFRs CAGE MFRs name
19、 and address0S2B1 RME Filters, IncorporatedP. O. Box 83898 Route 101 AAmherst, NH 03031-083805245 CORCOM, Incorporated844 East Rockland RoadLibertyville, IL 6004864135 Filter Concepts, Incorporated2624 S. Rousselle StreetSanta Ana, CA 92707Provided by IHSNot for ResaleNo reproduction or networking p
20、ermitted without license from IHS-,-,-A-A-55170B57.6 Part number (PIN) supersession data. This CID supersedes the following manufacturers PINs as shown. Thisinformation is being provided to assist in reducing proliferation in the government inventory system.TABLE II. PIN supersession data.MFRs CAGE0
21、S2B1MFRs CAGE64135MFRs CAGE05245PINAA55170- MFRs Commercial PIN 1/01 RME-A-310-S SF10 S 10VR602 RME-A-320-S SF20 20VR61/ The manufacturers PIN shall not be used for procurement to the requirements of this CID.At the time of preparation of this CID, the aforementioned commercial products were reviewe
22、dand could be replaced by the CID PIN shown. For actual part marking requirements, see 3.11.7.7 Government users. To acquire information on obtaining these filters from the Government inventory system,contact Defense Supply Center Columbus, ATTN: DSCC-VAT, Post Office Box 3990, Columbus, OH 43216-5000,telephone (614) 692-0562 or facsimile (614) 693-1644.MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY:GSA - 7FXECustodians:Navy - EC Preparing Activity:DLA-CCProject 5915-0408Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
