1、INCHPOUND AA59590/14B 14 November 2010 SUPERSEDING AA59590/14A 23 October 2005 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET HOLDER, ELECTRICAL CARD, WEDGE RETAINERS, 3 PIECE, SCREW ACTUATED DRIVE, .375 X .375 INCH BODY SIZE, WITH VISUAL LOCK INDICATION The General Services Administration has auth
2、orized the use of this commercial item description for all federal agencies. The complete requirements for procuring electrical card holders described herein shall consist of this document and the latest issue in effect of AA59590. CLASSIFICATION/PART IDENTIFICATION NUMBER (PIN). This commercial ite
3、m description (CID) specification sheet uses a classification system which is included in the Part Identification Number (PIN) as shown in the following example (see notes). AA59590 CID number /14 Applicable CID specification sheet B, C, H, R Finish * Mounting * * Length (see table I) W, D, E Config
4、uration (see table II) Example: AA59590/14CT38E is the PIN for a chemical film finished, 3.8 inch (96.5 mm) long visual lock indicating card holder. The card holder also features two tapped mounting holes for use with 080 UNF fasteners and a self-locking element on the end of the actuating screw for
5、 added resistance to loosening. SALIENT CHARACTERISTICS. Performance. Card holders shall hold the circuit card assembly firmly in its installed position. When the card holder is installed properly, it is capable of withstanding 60g/6ms of shock, 25 Grms of vibration, and provides from 2 to 4 degrees
6、 C/W/inch thermal resistance transfer between the circuit card assembly and the heat sink surfaces. Material. Unless otherwise specified herein, the card holder materials shall be as specified in AA59590. Interface and physical dimensions. The card holders supplied to this CID specification sheet sh
7、all be as specified on figures 1, 2, 3, and 4, in table I, and AA59590. Visual lock indicator (see figure 2). Card holders shall have a visual indicator to show when the card holder is in its relaxed (unlocked) state. When the card holder is in the unlocked (relaxed) state, the actuating end of the
8、screw shall display a red band on the side of the screw. When the actuating screw on the card holder has been tightened (assembly expanded) so that the assembly is in the locked position, this red band shall be concealed. Actuating screw hex drive socket. The across flats dimension for the hex drive
9、 socket shall be as follows: .140 inch (3.56 mm) for mounting options “J“, “N“, “T“, “R“, “V“, and “S“ and 3.0 mm (0.118 inch) for mounting options “G“ and “M“. Nominal installation torque. When card holders are used in cold plate applications, the nominal installation torque of each card holder sha
10、ll be as follows: 16 to 20 inch-pounds (1.8 to 2.3 N-m) for assemblies using no options or option “W“ and 17 to 21 inch-pounds (1.9 to 2.5 N-m) for assemblies using options “E“ or “D“. AMSC N/A FSC 5998Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
11、AA59590/14B 2 Inches mm Inches mm Inches mm Inches mm .20 .27 5.1 6.9 .33 .375 8.4 9.5 .385 .470 9.8 11.9 .50 .70 12.7 17.8 NOTES: 1. Dimensions are in inches. Millimeters are given for general information only. 2. Unless otherwise specified, tolerances are .02 inch (0.51 mm) for two place decimals
12、and .010 inch (0.25 mm) for three place decimals. 3. The across flats dimension for hex drive socket shall be .140 inch (3.56 mm) for mounting options “J“, “N“, “R“, “T“, “S“, and “V“. The across flats dimension for hex drive socket shall be a metric dimension of 3.0 mm (0.118 inch) across flats for
13、 mounting option “G“ and “M“. FIGURE 1. Relaxed and expanded dimensions. FIGURE 2. Visual lock indicator. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/14B 3 Cold plate slot width dimensions (when applicable). The recommended cold plate slo
14、t width to accommodate the circuit card assembly with attached card holder is .425 inch (10.80 mm) plus the thickness of the printed board of the circuit card assembly (see AA59590). Finish. The finish designator shall be as specified in AA59590. The finishes available for this CID specification she
15、et are as follows: “B“ (black anodize), “C“ (gold chemical film), “H“ (hard black anodize), or “R“ (clear chemical film). Mounting. The mounting designators shall be as specified in AA59590. The mounting options available for this CID specification sheet are as follows: “J“ (rivet mounting holes), “
16、N“ (no mounting holes), “T“ or “R“ (tapped 080 UNF 2B holes), “V“ or “S“ (tapped 256 UNC 2B holes), or “G“ or “M“ (tapped M2.5 x.45 metric holes). Card holders using mounting option “J“ may be shipped unassembled. See figure 1 for mounting hole spacing requirements. Mounting hole locations (when req
17、uired). When mounting holes are specified in the PIN, two mounting holes are required on card holders less than 5.30 inches (134.6 mm) in length. Three mounting holes may be present on card holders greater than 5.30 inches (134.6 mm) in length. The third mounting hole, when present, shall be centere
18、d on the mounting body. See figure 1 and table I and for mounting hole locations and spacing requirements. Rivet mounting holes. The holes used for rivet mounting shall be .136 inch (3.45 mm) diameter through holes, countersunk 100 degrees by .190 to .200 inch (4.83 to 5.08 mm) diameter with an acce
19、ss/clearance counterbore hole of .190 to .200 inch (4.83 to 5.08 mm) diameter by .300 inch (7.62 mm) deep. Rivets. This card holder uses rivet style B as specified in AA59590 when rivet mounting is used. Length, expanded, and relaxed dimensions. The length, expanded, and relaxed dimensions shall be
20、as specified on figure 1. The length designator shall be as specified in AA59590 and the available lengths for this specification sheet are listed in table I. TABLE I. Assembly dimensions (see figure 1). 1/ PIN length designator Dimension “LENGTH“ .02 (0.5) Dimension “A“ (maximum) Dimension “B“ .03
21、(0.8) Dimension “C“ .005 (0.13) 28 2.8 (71.1) 3.30 (83.8) 2.05 (52.1) .65 (16.5) 33 3.3 (83.8) 3.80 (96.5) 2.55 (64.8) 1.15 (29.2) 38 3.8 (96.5) 4.30 (109.2) 3.05 (77.5) 1.65 (41.9) 43 4.3 (109.2) 4.80 (121.9) 3.55 (90.2) 2.15 (54.6) 48 4.8 (121.9) 5.30 (134.6) 4.05 (102.9) 2.65 (67.3) 53 5.3 (134.6
22、) 5.80 (147.3) 4.55 (115.6) 3.15 (80.0) 58 5.8 (147.3) 6.30 (160.0) 5.05 (128.3) 3.65 (92.7) 1/ Dimensions are in inches. Millimeters, in parenthesis, are given for information only. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/14B 4 Confi
23、guration. The configuration of a card holder shall be as specified in table II. The details of a particular configuration consist of those on figures 1 and 2, and may include those on figures 3 and 4. Card holders not requiring the options described by table II shall leave the configuration position
24、 in the PIN blank. TABLE II. Configurations. Configuration Applicable figures Hardware options - 1 and 2 No added options W 1, 2, and 3 Lockwasher and flat washer E 1, 2, and 4 Screw self-locking element D 1, 2, 3, and 4 Lockwasher, flat washer and screw self-locking element Lockwasher and flat wash
25、er (see figure 3). A lockwasher and flat washer located under the screw head will provide for additional resistance to loosening from shock and vibration. Card holders requiring a lockwasher and flat washer shall include a suffix “W“ in the PIN (see classification and notes). FIGURE 3. Lockwasher an
26、d flat washer details. Screw self-locking element (see figure 4). The use of a screw self-locking element will provide prevailing torque for resistance to loosening from shock and vibration. Card holders requiring a screw self-locking element shall include a suffix “E“ in the PIN (see classification
27、 and notes). FIGURE 4. Screw self-locking element details. Lockwasher, flat washer, and screw self-locking element. Card holders requiring a lockwasher, flat washer, and screw self-locking element configuration shall include a suffix “D“ in the PIN (see classification and notes). Provided by IHSNot
28、for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/14B 5 NOTES. PIN. The PIN should be used for Government purposes to buy commercial products to this CID specification sheet. See the classification section for PIN format example. Source of documents. Commercial I
29、tem Description AA59590 Holder, Electrical Card, Wedge Retainers, 3 Piece, Screw Actuated Drive, General Requirements For. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or https:/assist.daps.dla.mil/ or from the Standardization Document Order Desk, 700 Ro
30、bbins Avenue, Building 4D, Philadelphia, PA 191115094.) Ordering data. Ordering data is as specified in AA59590. Commercial products. As part of the market analysis and research effort, this CID specification sheet was coordinated with the following manufacturers of commercial products. At the time
31、of preparation and coordination of this CID specification sheet, these manufacturers were known to have commercial products that would meet the requirements of this CID specification sheet. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict pr
32、ocurement to only the manufacturers shown.) Manufacturer CAGE Manufacturer name and address Manufacturer contact information 18915 Birtcher A Division of Pentair Electronic Packaging 7328 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 7402430
33、URL: 61081 Calmark A Division of Pentair Electronic Packaging 7328 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 7402430 Electronic mail: URL: 5BG68 Card Locks Unlimited, Inc. 2310 E. Orangethorpe Avenue Anaheim, CA 928061231 Telephone: (7
34、14) 7386194 Facsimile: (714) 4460119 E-mail: URL: Part number supersession data. This CID specification sheet PINS supersedes the following manufacturers part numbers as shown in table III. The CID PINs listed in table III are only for length designator “28“. See table IV for CID PIN construction
35、using other available lengths for this specification sheet. This information is being provided to assist in reducing proliferation in the Government inventory system. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/14B 6 TABLE III. Commercial
36、 part number supersession data. PIN designator AA59590/14 Vendor similar designator or type part number 1/ CAGE 18915 Vendor similar designator or type part number 1/ CAGE 61081 Vendor similar designator or type part number 1/ CAGE 5BG68 BJ28 44VI6B VA2502.80H 3250VBA2.80H BN28 44VI6BA VA2502.80 325
37、0VBA2.80 BT28 44VI6BT VA2502.80T0 3250VBA2.80T0 BV28 44VI6BS VA2502.80T2 3250VBA2.80T2 BG28 44VI6BM MVA2502.80TM2.5 3250MVBA2.80TM2.5 BJ28E 44VI6BL VA2502.80HL 3240VBA2.80HL BN28E 44VI6BAL VA2502.80L 3240VBA2.80L BT28E 44VI6BTL VA2502.80T0L 3240VBA2.80T0L BV28E 44VI6BSL VA2502.80T2L 3250VBA2.80T2L B
38、G28E 44VI6BML MVA2502.80TM2.5L 3250MVBA2.80TM2.5L BJ28W 44VI6BLF WVA2502.80H 3250VWBA2.80H BN28W 44VI6BLFA WVA2502.80 3250VWBA2.80 BT28W 44VI6BLFT WVA2502.80T0 3250VWBA2.80T0 BV28W 44VI6BLFS WVA2502.80T2 3250VWBA2.80T2 BG28W 44VI6BLFM MWVA2502.80TM2.5 3250MVWBA2.80TM2.5 BJ28D 44VI6BLFL WVA2502.80HL
39、3250VWBA2.80HL BN28D 44VI6BLFAL WVA2502.80L 3250VWBA2.80L BT28D 44VI6BLFTL WVA2502.80T0L 3250VWBA2.80T0L BV28D 44VI6BLFSL WVA2502.80T2L 3250VWBA2.80T2L BG28D 44VI6BLFML MWVA2502.80TM2.5L 3250MVWBA2.80TM2.5L CJ28 44VI6 V2502.80H 3250VCG2.80H CN28 44VI6A V2502.80 3250VCG2.80 CT28 44VI6T V2502.80T0 325
40、0VCG2.80T0 CV28 44VI6S V2502.80T2 3250VCG2.80T2 CG28 44VI6M MV2502.80TM2.5 3250MVCG2.80TM2.5 CJ28E 44VI6L V2502.80HL 3250VCG2.80HL CN28E 44VI6AL V2502.80L 3250VCG2.80L CT28E 44VI6TL V2502.80T0L 3250VCG2.80T0L CV28E 44VI6SL V2502.80T2L 3250VCG2.80T2L CG28E 44VI6ML MV2502.80TM2.5L 3250MVCG2.80TM2.5L S
41、ee footnote at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/14B 7 TABLE III. Commercial part number supersession data Continued. PIN designator AA59590/14 Vendor similar designator or type part number 1/ CAGE 18915 Vendor sim
42、ilar designator or type part number 1/ CAGE 61081 Vendor similar designator or type part number 1/ CAGE 5BG68 CJ28W 44VI6LF WV2502.80H 3250VWCG2.80H CN28W 44VI6LFA WV2502.80 3250VWCG2.80 CT28W 44VI6LFT WV2502.80T0 3250VWCG2.80T0 CV28W 44VI6LFS WV2502.80T2 3250VWCG2.80T2 CG28W 44VI6LFM MWV2502.80TM2.
43、5 3250MVWCG2.80TM2.5 CJ28D 44VI6LFL WV2502.80HL 3250VWCG2.80HL CN28D 44VI6LFAL WV2502.80L 3250VWCG2.80L CT28D 44VI6LFTL WV2502.80T0L 3250VWCG2.80T0L CV28D 44VI6LFSL WV2502.80T2L 3250VWCG2.80T2L CG28D 44VI6LFML MWV2502.80TM2.5L 3250MVWCG2.80TM2.5L HJ28 44VI6B3 VHA2502.80H 3250VBH2.80H HN28 44VI6B3A V
44、HA2502.80 3250VBH2.80 HT28 44VI6B3T VHA2502.80T0 3250VBH2.80T0 HV28 44VI6B3S VHA2502.80T2 3250VBH2.80T2 HG28 44VI6B3M MVHA2502.80TM2.5 3250MVBH2.80TM2.5 HJ28E 44VI6B3L VHA2502.80HL 3250VBH2.80HL HN28E 44VI6B3AL VHA2502.80L 3250VBH2.80L HT28E 44VI6B3TL VHA2502.80T0L 3250VBH2.80T0L HV28E 44VI6B3SL VHA
45、2502.80T2L 3250VBH2.80T2L HG28E 44VI6B3ML MVHA2502.80TM2.5L 3250MVBH2.80TM2.5L HJ28W 44VI6B3LF WVHA2502.80H 3250VWBH2.80H HN28W 44VI6B3LFA WVHA2502.80 3250VWBH2.80 HT28W 44VI6B3LFT WVHA2502.80T0 3250VWBH2.80T0 HV28W 44VI6B3LFS WVHA2502.80T2 3250VWBH2.80T2 HG28W 44VI6B3LFM MWVHA2502.80TM2.5 3250MVWBH
46、2.80TM2.5 HJ28D 44VI6B3LFL WVHA2502.80HL 3250VWBH2.80HL HN28D 44VI6B3LFAL WVHA2502.80L 3250VWBH2.80L HT28D 44VI6B3LFTL WVHA2502.80T0L 3250VWBH2.80T0L HV28D 44VI6B3LFSL WVHA2502.80T2L 3250VWBH2.80T2L HG28D 44VI6B3LFML MWVHA2502.80TM2.5L 3250MVWBH2.80TM2.5L See footnote at end of table. Provided by IH
47、SNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/14B 8 TABLE II. Commercial part number supersession data Continued. PIN designator AA59590/14 Vendor similar designator or type part number 1/ CAGE 18915 Vendor similar designator or type part number 1/ CAGE 61081 Vendor similar designator or type part number 1/ CAGE 5BG68 RJ28 44VI6CC VR2502.80H 3250VCC2.80H RN28
