1、ANLObOOL THRU ANLO6100 REV 3 53 7777735 0000270 2 a 637- AERIAL IDENTIFICATION PER ECO. RAISED OR DEPRESSED .o10 MAX .281 K TO PULL TP-cl - L - .O38 1.000 1.062 1.125 1.188 1.250 1.312 1.375 1.438 1.500 1.562 1.688 1.625 :e; 2.000 2.125 2.250 - - A - .798 .922 - 985 1.048 1.110 1.235 1.298 1.360 1.4
2、22 1.485 1.548 .e60 1.172 1.610 1 - 735 1.860 : - K +. O00 -.O60 - (9) -125 .188 .250 ,375 .438 .562 .625 .688 -750 .812 .e75 1.000 1.125 .312 .SOO 1. 250 L. 375 -016 OR CHAFnrEn OSINK BOTH ENDS 60. TO ,150 DIA - 2 HOLES- ON AXIS O THIS SURFACE MIST BE SQUARE WITH SHAm WITHIN -003 FULL INDICATOR REA
3、DING ANGULRR THD WITHIN LO2ATION .005. OF THIS fZOUP AS UNIT WY VARY PART NO. CHAMFER 30“ TO .750 DIA (OPPOSITE SIDE OPTIONAL) L - 2 - 375 2.500 2.625 :i; 3.000 3.125 3.250 3.375 3 * 500 3.625 3.750 3.875 4.000 4.125 4.250 4.500 4.625 4.375 $2; - A - 2 * 235 2. $85 2. 60 2.610 2.735 2.860 2.985 3.11
4、0 3.235 3.360 3 * 485 3.610 3.735 3.860 3 985 4.110 4 * 235 4.360 4.485 4.610 4.735 - K +.o00 -.o60 - li50C 1.75C 1.875 2.000 1.625 2.125 2.250 2.625 2 375 2.500 2.750 2 875 3.000 3.125 3.250 3-375 3.500 3.625 3.750 ;:E PART NO. AN106024 106025 106026 106027 106028 106029 106030 106031 106032 AN1060
5、33 AN106034 AN106035 AN106036 AN106037 106038 AN106039 AN106040 AN106041 AN106042 L - 5.000 5.125 5.250 5.375 5.500 5.625 ;:e; 6.000 - A - 4.86 4.98: 5.11C 5.235 5.360 5.485 5.610 ;:E PREELY - K t.0oc -. 06c - 4.125 4.250 4.500 4.625 4.750 4 875 5.000 5.125 4.375 PART NO, AN106045 AN106046 AN106048
6、AN106049 AN106047 106050 106051 A11106052 AN106053 (a) THREAD To HEAD. MAXIMUH TWO IHPERFECT THREADS. NOTE: (1) SHANK SHALL BE STRAIGHT WITHIN .O02 FIR. PER INCH OF BOLT LENGTH. (2) (3) THE CONCENTRICITY OF THREAD PO IN RELATION TO THE SHANK SHALL BE WITHIN THE CONCENTRICITY OF THE SHANK IN RELATION
7、 TO THE WASHER FACE DIAHETER AND HEXAGON .O06 FIR. SHALL BE WITHIN .O23 FIR. INACTIVE FOR DESIGN AFTER 27DEC 1966 NO SUPERSEDING STANDARD. HATERIAL: CORROSON RESISTANT STEEL - SEE HANUFACTURING SPECIFICATION SURFACE ROUGHNESS: AS107 HANUFACTURING SPECIFICATION: AHS 2472 INSPECTION: BREAK SHARP EDCES
8、 .003-.D15 UNLESS OTHERWISE SPECIFIED. ALL PARTS SHALL UNDERGO FLUORESCENT PENETRANT INSPECTION IN ACCORJANCE WITH AHS2645. DIHENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED: TOLERANCES; LINEAR DIHENSIONS .aio. ANGULAR DIHENSIONS 2. DO NOT USE UNASSIGNED PART NUHBERS. THIS STANDARD WAS DEVELOPED COOP
9、ERATIVELY WITH TiiE ENGINE AND PROPELLER UTILITY PARTS COHUITTEE OF THE SAE. P.A. Ocher Cusr AIR FORCE-NAVY AERONAUTICAL STANDARD AN I 0600 I USAF - 11 Navy - AS Army - AV THRU ANt06 100 BOLT - CRES HEX HEAD, DRILLED SHANK, .500-20 -1 001MPIT PwllRGolmL 1“11-111.111,.11 Project No. 5306-11 . THIS DOCUMENT CONTAINS - PAGES. 1 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
