1、REVISIONS LTR DESCRIPTION DATE APPROVED A Clarify VSWR and IL testing requirements as engineering info. 2 February 2010 Abdonasser M. Abdouni Prepared in accordance with ASME Y14.100 Source Control Drawing REV PAGE REV STATUS OF PAGES REV A A A A A PAGE 1 2 3 4 5 PMIC N/A PREPARED BY DEFENSE SUPPLY
2、CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 Ron Gary Original date of drawing 7 May 2001 CHECKED BY TITLE Lee Surowiec CONNECTOR, RECEPTACLE, ELECTRICAL, RF, SERIES N, JAMNUT MOUNTED, 75 OHM, FOR LOW SMOKE CABLES APPROVED BY Robert Heber SIZE CAGE CODE DWG. NO. 01026 A 037Z3 REV A PAGE 1 OF 5 AMSC N/
3、A 5935-E817-004 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZECAGE CODE DWG NO. A 037Z3 01026 REV A PAGE 2 NOTES: 1. Dimensions are in inches. Metric equivalents are in parenthesis. 2. Met
4、ric equivalents are given for information only. 3. All undimensioned pictorial configurations are for reference purposes only. 4. Series N, socket contact interface, 75, in accordance with figure 2. 5. Wrench flats to accommodate STD wrench openings in accordance with FED-STD-H28, appendix 10. FIGUR
5、E 1. General configuration. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZECAGE CODE DWG NO. A 037Z3 01026 REV A PAGE 3 JACK NOTES: 1. Dimensions are in inches. Metric equivalents are in pa
6、renthesis. 2. Metric equivalents are given information only. 3. Utilizes standard 50 body with 75 contact/air dielectric configuration. 4. ID to meet contact resistance, mating characteristics and connector durability when mated with a 036/.037 (0.091/0.094 mm) FIGURE 2. Interface, series N, socket
7、contact, 75. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZECAGE CODE DWG NO. A 037Z3 01026 REV A PAGE 4 ENGINEERING DATA: This document covers the requirements for radio frequency connecto
8、rs accommodating special low smoke coaxial cables. Frequency range: 0-2.5 GHz. VSWR: 1.30 :1, maximum. Insertion loss: .07 dB at 2 GHz. REQUIREMENTS: These connectors shall conform to all the requirements of the latest issue of DSCC drawing 84148, figures 1 and 2 herein, and MIL-PRF-39012/3, and acc
9、ommodate the cables listed in table I, with the following additions and exceptions. Electrical: Shall be in accordance with MIL-PRF-39012/3. Impedance: 75. Mechanical: Shall be in accordance with MIL-PRF-39012/3 with the following exceptions and additions: Gage requirements: Force to Engage/Disengag
10、e is the same as the 50 version (MIL-PRF-39012/3). Mating characteristics are as follows: Center contact (socket): Oversize test pin: .040 diameter, minimum (nonclosed entry contact only). Insertion depth: .125, minimum. Number of insertions: 1. Insertion force test: Steel test pin diameter .037 (0.
11、94 mm), minimum. Test pin finish: 16 microinches. Insertion force: 2 pounds, maximum. Withdrawal force test: Steel test pin diameter .036 (0.91 mm), maximum. Withdrawal force: 2 ounces, minimum. Test pin finish: 16 microinches. Environmental: Shall be in accordance with MIL-PRF-39012/3. Provided by
12、IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZECAGE CODE DWG NO. A 037Z3 01026 REV A PAGE 5 TABLE I. Cable accommodation. Part or Identifying Number (PIN) 1/ 2/ Applicable cable 01026NBSA M17/229-00001
13、 1/ These connectors have captivated center contacts. 2/ These connectors are assembled using the MIL-C-22520/5 crimp tool and using the following crimp dies: M22520/5-19 Closure A. Approved sources of supply. Approved sources of supply are listed herein. Additional sources will be added as they bec
14、ome available. The vendors listed below have agreed to this drawing and a certificate of compliance has been submitted to DSCC-VAI. DSCC drawing PIN Vendor CAGE number Vendor similar PIN 1/ 01026NBSA 00795 3190-885 1/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and test are met. Vendor CAGE Vendor name Number and address 00795 Delta Electronics 416 Cabot Street Beverly, MA 01915 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
