1、 REVISIONS LTR DESCRIPTION DATE APPROVED Prepared in accordance with ASME Y14.24 Vendor item drawing REV PAGE REV PAGE REV REV STATUS OF PAGES PAGE 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED BY RICK OFFICER DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 Original date of drawing YY-MM-DD
2、CHECKED BY RAJESH PITHADIA APPROVED BY ROBERT M. HEBER TITLE MICROCIRCUIT, LINEAR, DIFFERENTIAL AMPLIFIER, MONOLITHIC SILICON SIZE A CODE IDENT. NO. 16236 DWG NO. V62/09613 09-01-27 REV PAGE 1 OF 12 AMSC N/A 5962-V019-09 Provided by IHSNot for ResaleNo reproduction or networking permitted without li
3、cense from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/09613 REV PAGE 2 1. SCOPE 1.1 Scope. This drawing documents the general requirements of a high performance differential amplifier microcircuit, with an operating temperature range of -55C to +12
4、5C. 1.2 Vendor Item Drawing Administrative Control Number. The manufacturers PIN is the item of identification. The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation: V62/09613 - 01 X E Drawing Device type Case outline Lead fin
5、ish number (See 1.2.1) (See 1.2.2) (See 1.2.3) 1.2.1 Device type(s). Device type Generic Circuit function 01 INA159-EP Differential amplifier 1.2.2 Case outline(s). The case outline(s) are as specified herein. Outline letter Number of pins JEDEC PUB 95 Package style X 8 M0-187-AA Plastic surface mou
6、nt 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacture: Finish designator Material A Hot solder dip B Tin-lead plate C Gold plate D Palladium E Gold flash palladium Z Other Provided by IHSNot for ResaleNo reproduction or networki
7、ng permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/09613 REV PAGE 3 1.3 Absolute maximum ratings. 1/ Supply voltage (VCC) . +5.5 V Signal input terminals (-IN and +IN), voltage 30 V Reference (REF 1 and REF 2) and series p
8、ins: Current . 10 mA Voltage . -VCC 0.5 to +VCC+ 0.5 V Output short circuit (IOS) Continuous Storage temperature range (TSTG) -65C to +150C Junction temperature range (TJ) +150C Power dissipation (PD) . 833.33 mW Thermal resistance, junction to ambient (JA) 150C/W Thermal resistance, junction to cas
9、e (JC) . 78.495C/W Electrostatic discharge (ESD) rating: Human body model (HBM) . 4000 V Charged device model (CDM) 1000 V 1.4 Recommended operating conditions. 2/ Operating free-air temperature range (TA) -55C to +125C 1/ Stresses beyond those listed under “absolute maximum rating” may cause perman
10、ent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliab
11、ility. 2/ Use of this product beyond the manufacturers design rules or stated parameters is done at the users risk. The manufacturer and/or distributor maintain no responsibility or liability for product used beyond the stated limits. Provided by IHSNot for ResaleNo reproduction or networking permit
12、ted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/09613 REV PAGE 4 2. APPLICABLE DOCUMENTS JEDEC PUB 95 Registered and Standard Outlines for Semiconductor Devices (Applications for copies should be addressed to the Electronic Indu
13、stries Alliance, 2500 Wilson Boulevard, Arlington, VA 22201-3834 or online at http:/www.jedec.org) 3. REQUIREMENTS 3.1 Marking. Parts shall be permanently and legibly marked with the manufacturers part number as shown in 6.3 herein and as follows: A. Manufacturers name, CAGE code, or logo B. Pin 1 i
14、dentifier C. ESDS identification (optional) 3.2 Unit container. The unit container shall be marked with the manufacturers part number and with items A and C (if applicable) above. 3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characterist
15、ics are as specified in 1.3, 1.4, and table I herein. 3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are as specified herein. 3.5 Diagrams. 3.5.1 Case outline. The case outline shall be as shown in 1.2.2 and figure 1. 3.5.2 Terminal connections. T
16、he terminal connections shall be as shown in figure 2. 3.5.3 Test circuit for reference divider accuracy. The test circuit for reference divider accuracy shall be as shown in figure 3. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CE
17、NTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/09613 REV PAGE 5 TABLE I. Electrical performance characteristics. 1/ Limits Test Symbol Conditions 2/Temperature, TA Device type Min Max Unit Initial offset voltage 3/ VOS+25C 01 500 V VS= 2.5 V, reference and input pin grounded -
18、55C to +125C 1450 PSRR VS= 0.9 V to 2.75 V +25C 01 100 V/V Power supply rejection ratio -55C to +125C 200 +25C 01 0.024 % Reference divider 4/ accuracy -55C to +125C 0.050 Differential input 5/ impedance ZDIN+25C 01 240 typical k Common mode 5/ input impedance ZCM+25C 01 60 typical k +VCM+25C 01 17.
19、5 typical V Common mode voltage range -VCM-12.5 typical CMRR VCM= -10 V to +10 V, RS= 0 +25C 01 80 dB Common mode rejection ratio -55C to +125C 74 f = 0.1 Hz to 10 Hz -55C to +125C 01 10 typical VPPOutput voltage 6/ noise f = 10 kHz 30 typical nV / Hz Initial gain Gi VREF2= 4.096 V, RLconnected to G
20、ND, +VIN (-VIN) = -10 V to +10 V, VCM= 0 V +25C 01 0.2 typical V/V Gain error Ge VREF2= 4.096 V, RLconnected to GND, +25C 01 0.024 % +VIN (-VIN) = -10 V to +10 V, VCM= 0 V -55C to +125C 0.035 Nonlinearity gain Gn VREF2= 4.096 V, VCM= 0 V, RLconnected to GND, +VIN (-VIN) = -10 V to +10 V +25C 01 0.00
21、02 typical % of FS See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/09613 REV PAGE 6 TABLE I. Electrical performance characteristics
22、Continued. 1/ Limits Test Symbol Conditions 2/Temperature, TADevice type Min Max Unit Positive output voltage +VOUT+25C 01 +V 0.1 V VREF2= 4.096 V, RLconnected to GND -55C to +125C +V - 0.2 Negative output voltage -VOUT+25C 01 -V + 0.048 V VREF2= 4.096 V, RLconnected to GND -55C to +125C -V + 0.070
23、Current limit, continuous to common +25C 01 60 typical mA Capacitive load CLSee figure 4 pF Open loop output impedance ROf = 1 MHz, IO= 0 +25C 01 110 typical Small signal bandwidth SSBW -3 dB +25C 01 1.5 typical MHz Slew rate SR +25C 01 15 typical V/s Settling time, 0.01 % tS4 V output step, CL= 100
24、 pF +25C 01 1 typical s Overload recovery time 50% overdrive +25C 01 250 typical ns Power supply specified voltage range VS-55C to +125C 01 +5 V Power supply operating voltage range -55C to +125C 01 +1.8 +5.5 V IQ+25C 01 1.5 mA Power supply quiescent current -55C to +125C 2.0 1/ Testing and other qu
25、ality control techniques are used to the extent deemed necessary to assure product performance over the specified temperature range. Product may not necessarily be tested across the full temperature range and all parameters may not necessarily be tested. In the absence of specific parametric testing
26、, product performance is assured by characterization and/or design. 2/ Unless otherwise specified, at TA= +25C, RL= 10 k connected to VS/2, REF 1 pin connected to ground, and REF 2 pin connected to VREF= 5 V. 3/ Includes effects of amplifier input bias and offset currents. 4/ Reference divider accur
27、acy specifies the match between the reference divider resistor using figure 3. 5/ Internal resistors are ratio matched but have 20% absolute value. 6/ Includes effect of amplifier input current noise and terminal noise contribution of resistor network. Provided by IHSNot for ResaleNo reproduction or
28、 networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/09613 REV PAGE 7 Case X FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY C
29、ENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/09613 REV PAGE 8 Case X continued. Dimensions Inches Millimeters Symbol Min Max Min Max A - 0.043 - 1.10 A1 0.001 0.006 0.05 0.15 b 0.010 0.014 0.25 0.38 c 0.005 0.009 0.13 0.23 D 0.114 0.122 2.90 3.10 E 0.114 0.122 2.90 3.10 E1
30、0.187 0.199 4.75 5.05 e 0.026 BSC 0.65 BSC L 0.015 0.027 0.40 0.70 NOTES: 1. Controlling dimensions are millimeter, inch dimensions are given for reference only. 2. Reference dimension D, body length does not include mold flash, protrusion, or gate burrs. Mold flash, protrusion, or gate burrs shall
31、not exceed 0.15 mm (0.006 inch) per end. 3. Reference dimension E, body width does not include interlead flash. Interlead flash shall not exceed 0.50 mm (0.019 inch) per side. 4. Falls with JEDEC MO-187-AA. FIGURE 1. Case outline - Continued. Provided by IHSNot for ResaleNo reproduction or networkin
32、g permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/09613 REV PAGE 9 Device type 01 Case outline X Terminal number Terminal symbol 1 REF 1 2 -INPUT3 +INPUT 4 -VCC5 SENSE 6 OUTPUT 7 +VCC8 REF 2 FIGURE 2. Terminal connections.
33、 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/09613 REV PAGE 10 NOTE: The test is performed by measuring the output with the reference applied to alternate refe
34、rence resistors, and calculating a result such that the amplifier offset is cancelled in the final measurement. FIGURE 3. Test circuit for reference divider accuracy. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COL
35、UMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/09613 REV PAGE 11 Figure 4. Small signal overshoot versus load capacitance. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236
36、 DWG NO. V62/09613 REV PAGE 12 4. VERIFICATION 4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as indicated in their internal documentation. Such procedures should include proper handling of electrostatic sensitive devices, clas
37、sification, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manufacturers standard commercial practices for electrostatic discharge sensitive devices. 6. NO
38、TES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data contained herein is based on the salient characteristics of the device manufacturers data book. The device manufacturer reserves the right to make changes witho
39、ut notice. This drawing will be modified as changes are provided. 6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee of present or continued availability as a source of supply for the item. Vendor item drawing administr
40、ative control number 1/ 2/ Device manufacturer CAGE code Package 3/ Package designator Top side marking Vendor part number V62/09613-01XE 01295 Tape and reel DGK OAA INA159AMDGKTEP 1/ The vendor item drawing establishes an administrative control number for identifying the item on the engineering doc
41、umentation. 2/ For the most current package and ordering information, see the package option addendum at the end of the manufacturers data sheet , or use website . 3/ Package drawings, standard packaging quantities, thermal data, symbolization, and printed circuit board (PCB) design guidelines are a
42、vailable at CAGE code Source of supply 01295 Texas Instruments, Inc. Semiconductor Group 8505 Forest Lane P.O. Box 660199 Dallas, TX 75243 Point of contact: U.S. Highway 75 South P.O. Box 84, M/S 853 Sherman, TX 75090-9493 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
