DLA MIL-DTL-3928 29 A-2013 SWITCHES RADIO-FREQUENCY TRANSMISSION LINE (MICROSTRIP) (ELECTRICALLY OPERATED) CLASS 15 (PIN-MOUNTED) 1P2T.pdf

上传人:fuellot230 文档编号:690735 上传时间:2018-12-30 格式:PDF 页数:4 大小:56.17KB
下载 相关 举报
DLA MIL-DTL-3928 29 A-2013 SWITCHES RADIO-FREQUENCY TRANSMISSION LINE (MICROSTRIP) (ELECTRICALLY OPERATED) CLASS 15 (PIN-MOUNTED) 1P2T.pdf_第1页
第1页 / 共4页
DLA MIL-DTL-3928 29 A-2013 SWITCHES RADIO-FREQUENCY TRANSMISSION LINE (MICROSTRIP) (ELECTRICALLY OPERATED) CLASS 15 (PIN-MOUNTED) 1P2T.pdf_第2页
第2页 / 共4页
DLA MIL-DTL-3928 29 A-2013 SWITCHES RADIO-FREQUENCY TRANSMISSION LINE (MICROSTRIP) (ELECTRICALLY OPERATED) CLASS 15 (PIN-MOUNTED) 1P2T.pdf_第3页
第3页 / 共4页
DLA MIL-DTL-3928 29 A-2013 SWITCHES RADIO-FREQUENCY TRANSMISSION LINE (MICROSTRIP) (ELECTRICALLY OPERATED) CLASS 15 (PIN-MOUNTED) 1P2T.pdf_第4页
第4页 / 共4页
亲,该文档总共4页,全部预览完了,如果喜欢就下载吧!
资源描述

1、AMSC N/A FSC 5985 MIL-DTL-3928/29A 28 January 2013 SUPERSEDING MIL-DTL-3928/29 23 December 2005 DETAIL SPECIFICATION SHEET SWITCHES, RADIO-FREQUENCY TRANSMISSION LINE (MICROSTRIP) (ELECTRICALLY OPERATED) CLASS 15, (PIN-MOUNTED) 1P2T This specification is approved for use by all Departments and Agenc

2、ies of the Department of Defense. Requirements for acquiring the switches described herein shall consist of this specification sheet and MIL-DTL-3928. NOTES: 1. Dimensions are in inches. 2. Metric equivalents may be determined using 1.00 inch = 25.4 mm. 3. Unless otherwise specified, tolerances are

3、005 ( 0.13 mm) for three place decimals and .02 ( 0.5 mm) for two place decimals. FIGURE 1. Switch configuration and schematic, part or identifying numbers M3928/29-01, M3928/29-02, M3928/29-03, M3928/29-04, M3928/29-05, and M3928/29-06. INCH-POUND Provided by IHSNot for ResaleNo reproduction or ne

4、tworking permitted without license from IHS-,-,-MIL-DTL-3928/29A 2 NOTES: 1. Dimensions are in inches. 2. Metric equivalents may be determined using 1.00 inch = 25.4 mm. 3. Unless otherwise specified, tolerances are .005 ( 0.13 mm) for three place decimals and .02 ( 0.5 mm) for two place decimals. F

5、IGURE 2. Switch configuration and schematic, part or identifying numbers M3928/29-07, M3928/29-08, M3928/29-09, M3928/29-10, M3928/29-11, and M3928/29-12. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AMSC N/A FSC 5985 TABLE I. Electrical and perfo

6、rmance characteristics. Part or identifying number M3928/29- Fig. No. Hous-ing Fre-quency range dc to GHz VSWR Max Insertion loss (dB) Max Isolation (dB) Min Switch time (ms) Max Position indication circuit and rating Life cycles x 1000 Min Fail-safe or latching Operating current (A) 1/ Max Holding

7、current (A) 1/ Max Nominal operating voltage Pickup voltage (less than) Dropout voltage (less than) Power and indicator connector Weight (oz) Max 01N, S 1 0 18 1.7:1 2/ 0.7 3/ 50 4/ 15 None 1,000 F 0.1 0.1 28 V dc 20 V dc - Pin- mounted .75 02N, S 1 0 8 1.4:1 0.4 60 15 None 1,000 F 0.1 0.1 28 V dc 2

8、0 V dc - Pin-mounted .75 03N, S 1 0 18 1.7:1 2/ 0.7 3/ 50 4/ 15 None 1,000 F 0.17 0.17 12 V dc 10 V dc - Pin-mounted .75 04N, S 1 0 8 1.4:1 0.4 60 15 None 1,000 F 0.17 0.17 12 V dc 10 V dc - Pin-mounted .75 05N, S 1 0 18 1.7:1 2/ 0.7 3/ 50 4/ 15 None 1,000 F 0.4 0.4 5 V dc 4.5 V dc - Pin-mounted .75

9、 06N, S 1 0 8 1.4:1 0.4 60 15 None 1,000 F 0.4 0.4 5 V dc 4.5 V dc - Pin- mounted .75 07 N, S 2 0 18 1.7:1 2/ 0.7 3/ 50 4/ 15 None 1,000 L 0.1 0 28 V dc 20 Vdc - Pin- mounted 1.0 08 N, S 2 0 8 1.4:1 0.4 60 15 None 1,000 L 0.1 0 28 V dc 20 Vdc - Pin- mounted 1.0 09 N, S 2 0 18 1.7:1 2/ 0.7 3/ 50 4/ 1

10、5 None 1,000 L 0.17 0 12 V dc 10 V dc - Pin- mounted 1.0 10 N, S 2 0 8 1.4:1 0.4 60 15 None 1,000 L 0.17 0 12 V dc 10 V dc - Pin- mounted 1.0 11 N, S 2 0 18 1.7:1 2/ 0.7 3/ 50 4/ 15 None 1,000 L 0.4 0 5 V dc 4.5 V dc - Pin- mounted 1.0 12 N, S 2 0 8 1.4:1 0.4 60 15 None 1,000 L 0.4 0 5 V dc 4.5 V dc

11、 - Pin- mounted 1.0 1/ At nominal voltage and 20C. 2/ The VSWR at DC to 8 GHz is 1.4:1 maximum. 3/ The insertion loss at DC to 8 GHz is 0.4 dB maximum. 4/ The isolation at DC to 8 GHz is 60 dB minimum. 3MIL-DTL-3928/29AProvided by IHSNot for ResaleNo reproduction or networking permitted without lice

12、nse from IHS-,-,-MIL-DTL-3928/29A 4 REQUIREMENTS: Dimensions and configurations: See figures 1 and 2. Termination: Open. Nominal impedance: 50 ohms. RF connections: Pins for printed circuit (pc) mount. Pins are soldered to microstrip. Electrical and performance characteristics: See table I. RF conta

13、cts: Break before make. RF power handling capability: 10 watts. Operating temperature: -55C to +85C. Dielectric withstanding voltage: Actuator pins: 500 V dc. RF pins: 250 V rms. Solar radiation: Not applicable. RF energy leakage: Not applicable. Terminal strength: Not applicable. Part or Identifyin

14、g Number: M3928/29- (and dash number from table I). Referenced documents: This specification sheet only references MIL-DTL-3928. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Custodians: Preparing activity: A

15、rmy - CR DLA - CC Navy - EC Air Force - 85 (Project 5985-2013-004) DLA - CC Review activities: Army - AV, MI Navy - AS, MC, OS Air Force 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

展开阅读全文
相关资源
猜你喜欢
  • ASTM E1346-2016 Standard Practice for Bulk Sampling Handling and Preparing Edible Vegetable Oils for Sensory Evaluation《为作感官评价而对食用植物油进行大量取样 搬运和制备的标准实施规程》.pdf ASTM E1346-2016 Standard Practice for Bulk Sampling Handling and Preparing Edible Vegetable Oils for Sensory Evaluation《为作感官评价而对食用植物油进行大量取样 搬运和制备的标准实施规程》.pdf
  • ASTM E1347-2006 Standard Test Method for Color and Color-Difference Measurement by Tristimulus Colorimetry《用三色激励测色法测量颜色和色差的标准试验方法》.pdf ASTM E1347-2006 Standard Test Method for Color and Color-Difference Measurement by Tristimulus Colorimetry《用三色激励测色法测量颜色和色差的标准试验方法》.pdf
  • ASTM E1347-2006(2011) Standard Test Method for Color and Color-Difference Measurement by Tristimulus Colorimetry《用三色激励测色法测定颜色与色差的标准试验方法》.pdf ASTM E1347-2006(2011) Standard Test Method for Color and Color-Difference Measurement by Tristimulus Colorimetry《用三色激励测色法测定颜色与色差的标准试验方法》.pdf
  • ASTM E1347-2006(2015) Standard Test Method for Color and Color-Difference Measurement by Tristimulus Colorimetry《使用三色比色法测定颜色和色差的标准试验方法》.pdf ASTM E1347-2006(2015) Standard Test Method for Color and Color-Difference Measurement by Tristimulus Colorimetry《使用三色比色法测定颜色和色差的标准试验方法》.pdf
  • ASTM E1348-2002(2007) Standard Test Method for Transmittance and Color by Spectrophotometry Using Hemispherical Geometry《用半球体几何形状的分光光度法测量透明度和颜色的测试方法》.pdf ASTM E1348-2002(2007) Standard Test Method for Transmittance and Color by Spectrophotometry Using Hemispherical Geometry《用半球体几何形状的分光光度法测量透明度和颜色的测试方法》.pdf
  • ASTM E1348-2011 Standard Test Method for Transmittance and Color by Spectrophotometry Using Hemispherical Geometry《使用半球形几何学的透射比和颜色的分光光度标准试验方法》.pdf ASTM E1348-2011 Standard Test Method for Transmittance and Color by Spectrophotometry Using Hemispherical Geometry《使用半球形几何学的透射比和颜色的分光光度标准试验方法》.pdf
  • ASTM E1348-2015 Standard Test Method for Transmittance and Color by Spectrophotometry Using Hemispherical Geometry《使用半球体几何形状的分光光度法测量透明度和颜色的标准试验方法》.pdf ASTM E1348-2015 Standard Test Method for Transmittance and Color by Spectrophotometry Using Hemispherical Geometry《使用半球体几何形状的分光光度法测量透明度和颜色的标准试验方法》.pdf
  • ASTM E1348-2015e1 Standard Test Method for Transmittance and Color by Spectrophotometry Using Hemispherical Geometry《采用半球体几何形状的分光光度法测定透明度和颜色的标准试验方法》.pdf ASTM E1348-2015e1 Standard Test Method for Transmittance and Color by Spectrophotometry Using Hemispherical Geometry《采用半球体几何形状的分光光度法测定透明度和颜色的标准试验方法》.pdf
  • ASTM E1349-2006 Standard Test Method for Reflectance Factor and Color by Spectrophotometry Using Bidirectional (45 0 or 0 45) Geometry《用双向几何形状的分光光度法测量反射系数和颜色的测试方法(45 0 或 0 45)》.pdf ASTM E1349-2006 Standard Test Method for Reflectance Factor and Color by Spectrophotometry Using Bidirectional (45 0 or 0 45) Geometry《用双向几何形状的分光光度法测量反射系数和颜色的测试方法(45 0 或 0 45)》.pdf
  • 相关搜索

    当前位置:首页 > 标准规范 > 国际标准 > 其他

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1