1、 MIL-DTL-83528/12D 23 July 2013 SUPERSEDING MIL-DTL-83528/12C 15 November 2001 DETAIL SPECIFICATION SHEET GASKETING MATERIAL, CONDUCTIVE, SHIELDING GASKET, ELECTRONIC, ELASTOMER, ELECTRICAL, EMI/RFI, FLAT CIRCULAR WASHER This specification is approved for use by all Departments and Agencies of the D
2、epartment of Defense. The requirements for acquiring the relay described herein shall consist of this specification sheet and the latest issue of MIL-DTL-83528. FIGURE 1. EMI/RFI gasket, elastomer, flat circular washer. AMSC N/A FSC 5999 INCH-POUND Provided by IHSNot for ResaleNo reproduction or net
3、working permitted without license from IHS-,-,-MIL-DTL-83528/12D 2 REQUIREMENTS: Design and interface: See figure 1 and table I. Material: Type A, B, C, D, E, F, H, J, K, L, or M. Part or Identifying Number (PIN): See table I. Supersession information: See table II. TABLE I. Dimensions. PIN 1/ M8352
4、8/012X Nominal dimension 2/ 3/ Cross section 4/ area (cm2) A B T 001 0.250 (6.35) 0.625 (15.86) 0.031 (0.79) 0.038 002 0.062 (1.57) 0.075003 0.375 (9.53) 0.750 (19.05) 0.031 (0.79) 0.038 004 0.062 (1.57) 0.075005 0.500 (12.70) 0.656 (16.66) 0.031 (0.79) 0.016 006 0.062 (1.57) 0.031007 0.500 (12.70)
5、0.875 (22.23) 0.031 (0.79) 0.037 008 0.062 (1.57) 0.075009 0.750 (19.50) 1.000 (25.40) 0.031 (0.79) 0.025 010 0.062 (1.57) 0.050011 1.000 (25.40) 1.438 (36.53) 0.031 (0.79) 0.044 012 0.062 (1.57) 0.0881/ “X” in the PIN shall be replaced by the applicable material type. Complete PIN example: M83528/0
6、12A001. 2/ Dimensions are in inches; metric equivalents are given in parenthesis and are for general information only. 3/ Tolerance shall be as follows: Dimensions Tolerance Under .101 (2.57) .101 to .200 (2.57 to 5.08) .201 to .300 (5.10 to 7.62) .301 to .500 (7.62 to 12.70) .005 (0.13) .008 (0.20)
7、 .010 (0.25) .015 (0.38) 4/ For calculation of volume resistivity (for reference only). TABLE II. Supersession information. PIN 1/ M83528/012X Superseded DESC Drawing PIN 85111X 1/ 001 001002 002003 003004 004005 005006 006007 007 008 008009 009010 010011 011012 0121/ “X” in the PIN indicates the ap
8、plicable material type. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83528/12D 3 Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. Thi
9、s was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the
10、last previous issue. Referenced documents. This document references MIL-DTL-83528. Custodians: Preparing activity: Army CR DLA CC Navy EC Air Force 85 (Project 5999-2013-009) DLA CC Review activities: Air Force 19, 99 NSA NS NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
