1、 MIL-DTL-83528/5E 15 August 2013 SUPERSEDING MIL-DTL-83528/5D 15 November 2001 DETAIL SPECIFICATION SHEET GASKETING MATERIAL, CONDUCTIVE, SHIELDING GASKET, ELECTRONIC, ELASTOMER, EMI/RFI, O-RING, NON-STANDARD This specification is approved for use by all Departments and Agencies of the Department of
2、 Defense. The requirements for acquiring the relay described herein shall consist of this specification sheet and the latest issue of MIL-DTL-83528. NOTES: 1. Dimensions are in inches; metric equivalents are given in parenthesis and are for general information only. 2. Tolerance on flash shall be .0
3、08 (0.20 mm) on the extension and .005 (0.13 mm) on the thickness. FIGURE 1. EMI/RFI O-ring gasket. AMSC N/A FSC 5999 INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83528/5E 2 REQUIREMENTS: Design and interface: See figure 1 and t
4、able I. Material: Type A, B, C, D, E, F, H, J, K, L, or M. Part or Identifying Number (PIN): See table I. Supersession information: See table II. TABLE I. Dimensions. 6/ PIN 1/ M83528/005X Dimension 6/ Cross Section Area (cm2) 5/ B 2 / 3/ C 2/ 4/ 001 .030 (.76) .442 (11.23) .0046 002 .030 (.76) .577
5、 (14.66) .0046 003 .030 (.76) .692 (17.58) .0046 004 .030 (.76) .817 (20.75) .0046 005 .039 (.99) .425 (10.80) .0077 006 .048 (1.22) .295 (7.49) .0117 007 .050 (1.27) .533 (13.54) .0127 008 .051 (1.30) .446 (11.33) .0132 009 .057 (1.45) .415 (10.54) .0165 010 .063 (1.60) .541 (13.74) .0201 011 .063
6、(1.60) .648 (16.46) .0234 012 .068 (1.73) .847 (21.51) .0234 013 .068 (1.73) 1.182 (30.02) .0234 014 .068 (1.73) 3.165 (80.39) .0234 015 .070 (1.78) .495 (12.57) .0248 016 .070 (1.78) .610 (15.49) .0248 017 .070 (1.78) .635 (16.13) .0248 018 .070 (1.78) .667 (16.94) .0248 019 .070 (1.78) .860 (21.84
7、) .0248 020 .070 (1.78) 1.230 (31.24) .0248 021 .103 (2.62) 1.040 (26.42) .0538 022 .103 (2.62) 1.612 (40.94) .0538 023 .103 (2.62) 1.790 (45.47) .0538 1/ “X” in the PIN shall be replaced by the applicable material type. Complete PIN example: M38528/005A001. 2/ Dimensions are in inches; metric equiv
8、alents are given in parenthesis and are for general information only. 3/ Tolerance on dimension B shall be .003 for parts with a diameter of .070 and below; .005 for diameters from .101 to .200. 4/ Tolerance on dimension C shall be .010 for parts from .000 to 1.500, .015 for parts from over 1.500 to
9、 2.500 .020 for parts from over 2.500 to 4.500. 5/ For calculation of volume resistivity (for reference only). 6/ See MIL-DTL-83528/2 for additional sizes. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83528/5E 3 TABLE II. Supersession info
10、rmation. PIN M83528/005X Superseded DESC Drawing PIN 85105X 1/ 2/ 001 001002 002003 003 004 004005 005006 006 007 007008 008009 009 010 010011 011012 012 013 013014 014015 020 016 022017 023018 024 019 030020 038021 068 022 072023 0741/ “X” in the PIN indicates the applicable material type. 2/ Dimen
11、sions of this part are not identical to the superseded part. However, this is an authorized substitution. Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and
12、 the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Referenced docu
13、ments. In addition to MIL-DTL-83528, this document references the following: MIL-DTL-83528/2 Custodian: Preparing activity: Army CR DLA CC Navy EC Air Force 85 (Project 5999-2013-013) DLA CC Review activities: Air Force 19, 99 NSA NS NOTE: The activities listed above were interested in this document
14、 as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
