1、AMSC N/A FSC 5960 MIL-PRF-1/1635C 26 May 2009 SUPERSEDING MIL-PRF-1/1635B(CR) 9 July 1998 PERFORMANCE SPECIFICATION SHEET ELECTRON TUBE, CATHODE RAY TYPE 10ALP19 This specification is approved for use by all Depart- ments and Agencies of the Department of Defense. The requirements for acquiring the
2、electron tube described herein shall consist of this specification sheet and MIL-PRF-1. DESCRIPTION: Electrostatic deflection and focus, special deflection structure for minimum deflection defocusing, aluminized screen. Dimensions and pin connections: See figure 1. ABSOLUTE RATINGS: Parameter: Unit:
3、 Ef V Ec1 V dc Eb1 V dc Eb2 V dc ed v Rg Meg Zd Meg 1/ Maximum: Minimum: 6.9 5.7 0 -300 4,000 - 10,000 5,000 1,200 - 1.5 - 5.0 - Test conditions: 2/ 6.3 Adjust Focus 8,000 - - -See footnotes at end of table I. _ GENERAL: Qualification: Not Required. INCH-POUND Provided by IHSNot for ResaleNo reprodu
4、ction or networking permitted without license from IHS-,-,-MIL-PRF-1/1635C 2 TABLE I. Testing and inspection. Limits Inspection Method MIL-STD-1311 Notes Conditions Symbol Min Max UnitPreproduction sample approval inspection Pressure (implosion) 1141 5/ - - - - - Direct-interelectrode capacitance 13
5、31 - Grid 1 to allD1 to D2 D3 to D4 D1 to all D2 to all D3 to all D4 to all Cg1C1D2 C3D4 CD1 CD2 CD3 CD4 - - - - - - 12.5 7.0 3.0 14.5 14.5 8.0 8.0 pFpF pF pF pF pF pF Cathode illumination 5216 - - - - -Deflection - factor uniformity 5248 - - - 1.5 %Vibration 5111 - - - 1 mmShock 5115 10/- - - -Base
6、 material insulating quality 1216 - - - - -Conformance inspection part 1 Angle between traces 5101 - - 89 91 Degrees Bulb, screen, and faceplate quality 5106 - - - - -Voltage breakdown 5201 - - - - -Voltage breakdown (electrostatic types) 5201 - - - - -Gas “cross” (electrostatic deflection) 5206 6/
7、Beam current = 2.5 A dc - - - -Stray light emission (conventional types) 5216 - Eb = 10,000 V dc - - - -Modulation 5223 6/ Beam current = 2.5 A dc Ec1 - 20 V dcSpot position (electrostatic deflection) 5231 - - - 20 mmGrid-cutoff voltage 5241 - Ec1 -155 -205 V dcFocusing voltage at cutoff 5246 - Eb1
8、2,250 3,100 V dcSpot displacement (leakage) 5231 - - - 10 mmGrid No. 1 leakage current 5251 - - - - -See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-1/1635C 3 TABLE I. Testing and inspection - Continued. Limits
9、Inspection Method MIL-STD-1311 Notes Conditions Symbol Min Max UnitConformance inspection part 1 - Continued Spot examination - 7/ - - - - Minimum useful scan 1D2 3D4 - 6/- - Focused trace;beam current = 2.5 A dc- - 9 9 - - Inches Inches Screen charging - 8/ - - - -Deflection defocusing - 9/ - - 1:3
10、 RatioPattern distortion 5103 - - - 2 %Secureness of base, cap, or insert 1101 - - - - -Base pin solder depth 1111 - - - - -Permanence of marking 1105 3/ 4/ - - - -Conformance inspection part 2 Neck and base alignment (electrostatic types) 5101 - - - 1.5 Degrees Heater current 1301 - If 540 660 mABa
11、se alignment (electrostatic types) 5101 - +1D2, index pin - - - -Electrode current (anode No. 1) 5201 - Ib1 -15 +10 A dc Screens 5221 6/ - - - -Line width A (electrostatic deflection) 5226 6/ Beam current = 2.5 A dc - - 0.30 mmLine width B (electrostatic deflection) 5226 6/ Beam current = 2.5 A dc -
12、 - 0.42 mmAnode No. 1 leakage current 5251 - - - - -Anode No. 2 leakage current 5251 - - - - -Deflection factor 5248 - 1D2 - 155 189 V dc/inchDeflection factor 5248 - 3D4 - 151 185 V dc/inchSee footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without li
13、cense from IHS-,-,-MIL-PRF-1/1635C 4 TABLE I. Testing and inspection - Continued. Limits Inspection Method MIL-STD-1311 Notes Conditions Symbol Min Max UnitConformance inspection part 3 Life test - 6/ 10/ Group C; beam current = 2.5 A dc;Eb2 = 10,000 V dc; t = 500 hours (min) - - - - Life-test end p
14、oints: Modulation Line width A Line width B Grid No. 1 leakage current Anode No. 1 leakage current Anode No. 2 leakage current Stray light emission (conventional types) - 5223 5226 5226 5251 5251 5251 5216 - - - - - - - Ec1 - - - - - - - - - - - - - 20 0.30 0.42 - - - - V dc mm mm - - - - 1/ It is r
15、ecommended that the deflection electrode circuit resistances be approximately equal. 2/ The P19 screen may be permanently damaged if the current density is permitted to rise too high. To prevent burning, minimum beam current densities should be employed. 3/ Marking shall be in accordance with MIL-PR
16、F-1. If any specification requirements waiver has been granted, the product-identification marking shall consist of the tube type-number only. (See figure 1 herein.) 4/ The following additional marking requirement shall apply: A line, of adequately contrasting color to the base-material color, shall
17、 be drawn on the tube base parallel to the tube axis; this line shall be aligned with and on the same side as the index pin. 5/ Although all tests covered herein are required to be performed during preproduction sample approval inspection, the seven tests listed under this caption are performed, nor
18、mally, during preproduction sample approval only. 6/ Beam current shall be measured by applying a sufficient voltage to either D1 or D2 to deflect a 1 by 1-inch (25.4 by 25.4 mm) raster until the raster cannot be seen on the screen. Grid No. 1 bias voltage shall be adjusted so that either D1 or D2 w
19、ill collect 2.5 microamperes. 7/ With the focused spot just above visual cutoff, examine the spot for any abnormalities. The spot shall be of uniform brightness and shall not show any indication of a dual spot. This may be noted as an astigmatic spot of nonuniform brightness, or a spot the extremiti
20、es of which give the appearance of bright cores, with the center of the spot appearing dark. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-1/1635C 5 TABLE I. Testing and inspection - Continued. 8/ If used, visually check the internal alumin
21、um coating in the area between the edge of the faceplate and internal aquadag; it shall appear uniform and nearly opaque. If not, perform the following test: With a 1.5 by 1.5-inch (38.1 by 38.1 mm) slightly defocused raster, in accordance with method 5221, in the center of the screen, and with Eb2
22、= 10,000 volts, and with a beam current of 15 microamperes, there shall be no evidence of any doubling of the raster lines (venetian-blind effect), or a sawtooth effect at the edges of the raster. (Any doubling of the raster lines shall be intermittent only, giving the appearance of being pulsed.) R
23、epeat on the edges of the screen in the following positions: a. 45 clockwise from the plane of pin No. 1. b. 135 clockwise from the plane of pin No. 1. c. 225 clockwise from the plane of pin No. 1. d. 315 clockwise from the plane of pin No. 1. These tests shall be made quickly to prevent burning of
24、the screen; apply the grid drive momentarily. 9/ The ratio of the line width of a 2-inch (50.8 mm) long trace, adjusted for best center focus, to the line width measured on the faceplate axis when the trace is deflected perpendicularly plus or minus 4 inches (101.6 mm) from the face center by a bala
25、nced dc voltage, shall not be greater than the value specified herein. 10/ Unless otherwise specified, tubes subjected to the following destructive tests are not to be delivered on the contract: Shock; life test. Provided by IHSNot for ResaleNo reproduction or networking permitted without license fr
26、om IHS-,-,-MIL-PRF-1/1635C 6 NOTES: 1. Minimum useful screen diameter. 2. Metric equivalents are given for general information only and are based upon 1.00 inch = 25.4 mm. 3. Reference dimensions are for information only and are not required for inspection purposes. FIGURE 1. Outline drawing of elec
27、tron tube type 10ALP19.Pin number Element 1 Accelerator 3 & 4 Deflecting electrode D15 & 6 Deflecting electrode D29 Focusing electrode 11 & 14 Heater & cathode 12 & 13 Grid number 1 15 Heater 18 & 19 Deflecting electrode D320 & 21 Deflecting electrode D4Provided by IHSNot for ResaleNo reproduction o
28、r networking permitted without license from IHS-,-,-MIL-PRF-1/1635C 7 Dimensions (see note 2) Ltr Inches Millimeters Min Max Min Max Conformance inspection, part 2 A 10.375 DIA 10.625 DIA 263.53 DIA 269.88 DIA B 9.000 DIA - 228.60 DIA - F 11.375 11.875 288.93 301.63 G 15.500 16.000 393.70 406.40 H 1
29、9.750 20.250 501.65 514.35 J 3.469 3.656 88.11 92.86 K 1.594 RAD 1.969 RAD 40.49 RAD 50.01 RAD L 4.312 DIA 4.500 DIA 109.52 DIA 114.30 DIA Reference dimensions (see note 3) C 42.000 RAD 1066.80 RAD D 11.750 RAD 298.45 RAD E 1.000 RAD 25.40 RAD FIGURE 1. Outline drawing of electron tube type 10ALP19
30、- Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-1/1635C 8 Referenced documents. In addition to MIL-PRF-1, this document references the following: MIL-STD-1311 The margins of this specification are marked with vertical lines to in
31、dicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irre
32、spective of the marginal notations and relationship to the last previous issue. Custodians: Preparing activity: Army - CR DLA - CC DLA CC (Project 5960-2009-004) Review activities: Army - AV, CR4 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
