1、AMSC N/A FSC 5950 MIL-T-27/86A 28 April 2008 SUPERSEDING MIL-T-27/86 22 April 1976 DETAIL SPECIFICATION SHEET TRANSFORMERS AND INDUCTORS (AUDIO, POWER, AND HIGH-POWER PULSE), INDUCTOR, POWER This specification is approved for use by all Depart- ments and Agencies of the Department of Defense. The re
2、quirements for acquiring the products described herein shall consist of this specification and MIL-PRF-27. NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Tolerance on terminal position dimensions is .015. 4. Marking shall be on the side of the ca
3、se. FIGURE 1. Dimensions and configuration. INCH-POUND Inches mm .240 .420 6.10 10.67 Inactive for New Design after 14 February 1997 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-27/86A 2 REQUIREMENTS: (When numbers in parentheses, i.e. (1.-3
4、) are used, they indicate the winding and the extreme terminals of the winding.) Electrical ratings: Inductance (1-2): 50 H minimum. Voltage (1-2): 0.2 V rms, 10 kHz. Power: 0.063 watt. Current (1-2): 0.5 ampere dc. DC resistance (1-2): 0.25 ohm maximum. Working voltage: 50 V maximum. Design and con
5、struction: Dimensions and configuration: See figure 1. Duty cycle: Continuous. Case: Encapsulated. Material: Epoxy. Terminals: Solid wire lead type, tinned nickel. Weight: 1.1 grams maximum. Operating temperature range: -55C to +130C. Terminal strength: MIL-STD-202, method 211, test condition A, 2 p
6、ounds. Terminal twist: MIL-STD-202, method 211, test condition D. Dielectric withstanding voltage (at sea level): 100 volts rms. Electrical characteristics: Inductance: With 0.2 Vrms, 10 kHz across, and 0.5 ampere dc applied to (1-2) the inductance shall be 50 H minimum. DC resistance: 0.25 ohm acro
7、ss (1-2) maximum. VERIFICATION: Qualification inspection: Not applicable for this specification sheet. Quality conformance inspection: Groups A and B tests of MIL-PRF-27 shall be applicable. Marking location: See figure 1. Part or Identifying Number (PIN): M27/86-01. Provided by IHSNot for ResaleNo
8、reproduction or networking permitted without license from IHS-,-,-MIL-T-27/86A 3 Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes n
9、o liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Referenced documents. In addition to MIL
10、PRF-27, this document references the following: MIL-STD-202 Custodians: Preparing activity: Army CR DLA CC Navy EC Air Force 11 (Project 5950-2008-016) DLA - CC Review activities: Army AR, CR4, MI Navy AS, MC, OS, SH Air Force 19 NOTE: The activities listed above were interested in this document as
11、 of the date of this document. Since organizations and responsibilities can change, you should verify the currency of this information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
