1、AMSC N/A FSC 4730 MS27060E 1 May 2013 SUPERSEDING MS27060D 24 September 2003 DETAIL SPECIFICATION SHEET ADAPTER ASSEMBLY, FLARED, 90 FORGED ELBOW, TUBE TO HOSE WITH SWIVEL NUT This specification sheet is approved for use by all Departments and Agencies of the Department of Defense. The requirements
2、for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-27272. NOTES: 1. Dimension A, se table II, is measured between the hose end of the socket and the centerline of the insert when the socket is assembled on the elbow subassembly. 2. If required lockwire h
3、oles to be drilled on this side of subassembly in accordance with SAE-AS1043. 3. Socket may be hex or 2-flat-sides. FIGURE 1. Adapter assembly illustration. INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27060E 2 REQUIREMENTS: Adapter a
4、ssembly illustration, see figure 1. Intended use. This adapter is intended for use with hose conforming to MIL-DTL-27267. Materials. Material and material codes see table I. See applicable specification sheet and MIL-DTL-27272 for material of other components identified in table II for their materia
5、l requirements. TABLE I. Materials and material codes. Material code Material Blank Combination of aluminum alloy and corrosion-resistant steel (CRES) C CRES TABLE II. Adapter assembly composition. 1/ 2/ Size and material code Elbow subassembly size and material code Sleeve size and material code So
6、cket size and material code A max inch (mm) MS27060 MS27068 MS27070 3/ MS27069 3/ -3/-4C 4/ -3/-4C -4C -4C 1.54 (39.1) -4C -4C -5C -5C -5C -5C 1.63 (41.4) -6C -6C -6C -6C 1.71 (43.4) -8C -8C -8C -8C 2.09 (53.1) -8 -8 1/ Dimensions are in inches. 2/ Metric equivalents are given for general informatio
7、n only. 3/ MS27070 and MS27069 shall be dry film lubricated in accordance with table III, dry film is applied in accordance with MS27070 or MS27069 as applicable. 4/ Swivel nut and sealing surface of this elbow subassembly shall mate with SAE-AS4395-3 fitting. The remaining portion of the assembly s
8、hall mate with MIL-DTL-27267-4 hose If required, lockwire holes to be drilled in accordance with SAE-AS1043 and suffix L added to the Part or Identifying Number (PIN). MS27060 threads on -3/-4C through -8C shall be lubricated with dry-film lubricant in accordance with table III, no overspray allowed
9、. MS27070 and MS27069 parts shall be coated with the same type of dry film lubricant as indicated in the PIN, no mixing of dry film lubricants shall be used on an assembly unless it is of the types specified by the “blank” designator. NOTE: Avoid using graphite dry film lubes with aluminum nipples b
10、ecause in a wet environment, graphite becomes corrosive to the aluminum. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27060E 3 TABLE III. Dry film designator. Dry film designator SAE class or type designator Dry film characteristics Blank Any SA
11、E class or type below N/A SAE-AS1701 SAE-AS1701 class SAE-AS1701 temperature ranges F (C) 4 4 -65 to +1400F (-54 to 760C) 5 5 -65 to +850F (-54 to 454C) 6 6 -375 to +850F (-226 to 454C) SAE-AS5272 SAE-AS5272 type SAE-AS5272 temperature ranges. F (C) 7 Type I -90 to 400F (-68 to 204C) endurance life
12、of 250 min minimum 8 Type II -90 to 400F (-68 to 204C) endurance life of 450 min minimum 9 Type III Color 1 - Natural product color -90 to 400F (-68 to 204C) low Volatile organic compound with an endurance life of 450 min minimum 10 Type III Color 2 - Black color -90 to 400F (-68 to 204C) low Volati
13、le organic compound with an endurance life of 450 min minimum Dry film designator MIL classification Dry film characteristics MIL-PRF-46010 1/ - MIL-PRF-46010 temperature ranges. F (C) 11 1 Color 1 natural product color, -90 to 400F (-68 to 204C) solvent resisting 12 2 Color 2 - Black color -90 to 4
14、00F (-68 to 204C) solvent resisting 1/ Not for aerospace usage. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27060E 4 PIN: The PIN consists of prefix “MS”. the specification sheet number, dash number for 90 adapter assembly size, letter for mate
15、rial, and a blank or L for l for lockwire holes, and a blank or number for dry film lubricant. Unassigned PINs shall not be used. MS 27060 -8 C L 4 PIN examples: MS27060-8C indicates a 90 adapter assembly size 8, CRES with dry film class designator “blank”. MS27060-8C4 indicates a 90 adapter assembl
16、y size 8, CRES with dry film class designator 4. MS27060-8L indicates a 90 adapter assembly size 8, a combination of aluminum and CRES, with lockwire holes, and with dry film class designator “blank”. Identification of product. The PIN and the manufacturers Commercial and Government Entity (CAGE) Co
17、de shall be marked on a removable tag securely attached to the adapter. Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this doc
18、ument, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. Referenced documents shall be of the issue in effect on date of invitations for bid. Changes from previous issue. Marginal notations are not used in this revision to identify changes with respec
19、t to the previous issue, due to the extent of the changes. Referenced documents. In addition to MIL-DTL-27272, this document references the following: MIL-DTL-27267 MIL-PRF-46010 MS27068 MS20769 MS27070 SAE-AS1043 SAE-AS1701 SAE-AS4395 SAE-AS5272 Specification sheet number MS prefix Material code le
20、tter (see table I) Size code number (see table II) Blank or “L” for lockwire holes Dry film designator (see table III) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27060E 5 CONCLUDING MATERIAL Custodians: Preparing activity: Army - AV DLA - CC N
21、avy - AS Air Force - 99 (Project 4730-2013-018) DLA - CC Review activities: Army - AR, AT, MI Navy - MC, SA, SH Air Force - 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
