1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Paragraph 1.5, correct maximum total dose available from 300 Krads (Si) to 300 Krads (Si). Paragraph 4.3.5.1a, last sentence, correct 5962F0824601 to 5962F0921001. Update boilerplate paragraphs. -gz 11-04-05 Charles F. Saffle REV SHET REV SHET RE
2、V STATUS REV A A A A A A A A A A A OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY Gary Zahn DLA LAND AND MARITIME STANDARD MICROCIRCUIT DRAWING CHECKED BY Greg Cecil COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL APPROVED BY Charles F. Saffle
3、MICROCIRCUIT, HYBRID, LINEAR, POSITIVE, DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 09-07-29 LOW DROPOUT, ADJUSTABLE VOLTAGE REGULATOR AMSC N/A REVISION LEVEL A SIZE A CAGE CODE 67268 5962-09208 SHEET 1 OF 11 DSCC FORM 2233 APR 97 5962-E196-11Provided by IHSNot for Re
4、saleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-09208 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined
5、 in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the follow
6、ing example: 5962 F 09208 01 K X X Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall m
7、eet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type. The device type identify the circuit function as follows: Device type Generic number Circuit function 01 MSK 5824RH Radiation hardened, 3.5 A,
8、 adjustable voltage regulator 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Li
9、sting (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military quality class level. This level is intended for use in applications where
10、 non-space high reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified incoming flow, and the manufacturer guarantees (but m
11、ay not test) periodic and conformance inspections (Group A, B, C, and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the device acquisition document; therefore the
12、acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may have a limited temperature range. Provided
13、by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-09208 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 3 DSCC FORM 2234 APR 97 1.2.4 Case outlines. The case outlines are as designated in MIL-STD-
14、1835 and as follows: Outline letter Descriptive designator Terminals Package style X See figure 1 8 Flat pack with gull wing leads, glass sealed Y See figure 1 8 Flat pack with straight leads, glass sealed 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximu
15、m ratings. 1/ Input voltage (VIN) +7.0 V dc Output current 3.5 A 2/ Junction temperature (TJ) +150C Thermal resistance, junction-to-case (JC), TC= +125C . 6.5C/W Storage temperature -65C to +150C Lead temperature (soldering, 10 seconds) +300C 1.4 Recommended operating conditions. Input voltage range
16、 (VIN) +2.9 V dc to +6.5 V dcCase operating temperature range (TC). -55C to +125C 1.5 Radiation features. Maximum total dose available 300 Krads (Si) 3/ 4/ 5/ 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a
17、part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD
18、-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online a
19、t https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing tak
20、es precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 1/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and af
21、fect reliability. 2/ Output current limit is dependent on the value of VIN- VOUT. 3/ These parts may be dose rate sensitive in a space environment and may demonstrate enhanced low dose rate effects. Radiation end-point limits for the noted parameters are guaranteed only for the conditions as specifi
22、ed in MIL-STD-883, method 1019, condition A. Dose rate shall be in accordance with MIL-STD-883, method 1019, condition A. 4/ Bipolar device types may degrade from displacement damage from radiation which could affect RHA levels. These device types have not been characterized for displacement damage.
23、 5/ See figure 3. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-09208 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. Th
24、e individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 may include the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for the
25、applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or
26、 function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein and figure
27、1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Radiation exposure circuits. The radiation exposure circuits shall be as specified on figure 3. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance c
28、haracteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking
29、of devices. Marking of devices shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufactur
30、er of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any,
31、 are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DLA Land and Maritime-VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order
32、to supply to this drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime-VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-P
33、RF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturers Quality Management (QM) plan. The modification in
34、the QM plan shall not affect the form, fit, or function as described herein. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-09208 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 5 DSCC
35、 FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ 2/ 3/ -55C TC+125C unless otherwise specified Group A subgroups Device type Limits Unit Min MaxReference voltage VREFVIN= 3.3 V, IOUT= 50 mA, VOUT= VREF1,2,3 01 1.225 1.305 V M,D,P,L,R,F 1/ 1 01 1.225 1.310
36、Line regulation VRLINE2.97 V VIN 3.63 V, IOUT= 50 mA 1 01 -0.25 0.25 %/V 2,3 -0.50 0.50 Load regulation VRLOADVIN= 3.3 V, 50 mA IOUT 3.0 A 1 01 -1.0 1.0 %/A 2,3 -2.0 2.0 Dropout voltage VDOIOUT= 3.0 A 1,2,3 01 0.5 V Current limit 4/ IOUTVIN= 3.3 V 1,2,3 01 3.0 A Shutdown threshold VSTVIN= 3.3 V 1,2,
37、3 01 1.0 1.6 V Output voltage at shutdown VOUTSD VIN= VSHDN= 3.3 V, IOUT= 50 mA 1,2,3 01 -0.1 0.1 V 1/ Device type 01 has been characterized through all levels M, D, P, L, R, F of irradiation and tested to 1.5 times at the F level. Pre and post irradiation values are identical unless otherwise speci
38、fied in table I. When performing post irradiation electrical measurements for any RHA level, TC= +25C. 2/ Unless otherwise specified, VIN= 3.3 V, VSHUTDOWN= 0 V, VOUT= 2.5 V, and IOUT= 50 mA. 3/ These parts may be dose rate sensitive in a space environment and may demonstrate enhanced low dose rate
39、effects. Radiation end-point limits for the noted parameters are guaranteed only for the conditions as specified in MIL-STD-883, method 1019, condition A. 4/ Current limit is dependent upon the value of VIN. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IH
40、S-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-09208 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 6 DSCC FORM 2234 APR 97 Case outline X. Symbol Millimeters InchesMin Max Min Max A - 4.83 - .190 A1 0.076 0.18 .003 .007 b 0.58 0.69 .023 .027 D/E 18.92 19.18 .745 .755 D1 27.
41、18 27.69 1.070 1.090 e 2.54 TYP .100 TYP e1 7.49 7.75 .295 .305 L 2.79 3.81 .110 .150 L1 0.76 1.27 .030 .050 R 0.76 REF .030 REF S1 5.21 6.22 .205 .245 NOTES: 1. A1 is measured from the bottom of the lead to the bottom of the package. 2. Pin 1 is indicated by the ESD marking on the package. Pin numb
42、ers are for reference only. 3. The U. S. Government preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall take precedence. 4. Case out
43、line X weight: 5.5 grams typical. FIGURE 1. Case outlines. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-09208 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 7 DSCC FORM 2234 APR 97
44、Case outline Y. Symbol Millimeters InchesMin Max Min Max A - 4.57 - .180 A1 1.78 2.03 .070 .080 b 0.58 0.69 .023 .027 D/E 18.92 19.18 .745 .755 e 2.54 TYP .100 TYP e1 7.49 7.75 .295 .305 L 10.16 - .400 - S1 5.21 6.22 .205 .245 NOTES: 1. Pin 1 is indicated by the ESD class marking. Pin numbers are fo
45、r reference. 2. The U. S. Government preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall take precedence. 3. Pin numbers are for ref
46、erence only. 4. Case outline Y weight: 5.8 grams typical. FIGURE 1. Case outlines - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-09208 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LE
47、VEL A SHEET 8 DSCC FORM 2234 APR 97 Device type 01 Case outlines X and Y Terminal number Terminal symbol 1 2 3 4 5 6 7 8 GND GND SHUTDOWN ADJUST VOUTVOUTVINVINFIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MI
48、CROCIRCUIT DRAWING SIZE A 5962-09208 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 9 DSCC FORM 2234 APR 97 FIGURE 3. Radiation exposure circuits. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-09208 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVI
