1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with NOR 5962-R311-92. 92-09-24 Monica L. Poelking B Update to current requirements. Editorial changes throughout. - gap 06-05-16 Raymond Monnin The original first page of this drawing has been replaced. REV SHET REV B B B B
2、 B SHEET 15 16 17 18 19 REV STATUS REV B B B B B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Phu H. Nguyen DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Tim H. Noh COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS A
3、VAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Monica L. Poelking MICROCIRCUIT, DIGITAL, ECL, TWO-MODULUS PRESCALER, DIVIDE BY 5 AND 6, AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 92-06-29 MONOLITHIC SILICON AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 67268 5962-87748 SHEET 1 OF
4、19 DSCC FORM 2233 APR 97 5962-E203-06 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87748 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1
5、 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a cho
6、ice of Radiation Hardness Assurance (RHA) levels are reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 87748 01 M E X Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Lead finish (see 1.
7、2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked
8、 with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 12509 Two-modulus prescaler, an ECL to TTL translator, with divide by 5 and 6. 1.2.3 Device c
9、lass designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF
10、-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style E GDIP1-T16 or CDIP2-T16 16 Dual-in-line F GDFP2-F16 or CDFP3-F16 16 F
11、lat pack 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87748 D
12、EFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Supply voltage range (VCC) (VEE= 0) 0 V dc to +7.0 V dc Supply voltage range (VEE) (VCC= 0) . -8.0 V dc to 0.0 V dc Output voltage (VOUT) +5.5 V dc Input voltage (V
13、IN) +5.5 V dc Maximum power dissipation 460 mW Storage temperature range (TS) -65C to 175C Lead temperature (soldering,10 seconds) +300C Junction temperature (TJ) . +165C Thermal resistance, junction-to-case (JC) See MIL-STD-1835 1.4 Recommended operating conditions. Supply voltage (VCC) (VEE= 0) .
14、4.5 V dc minimum to 5.5 V dc maximum Supply voltage (VEE) (VCC= 0) . -5.46 V dc minimum to -4.94 V dc maximum Case operating temperature range (TC) -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form
15、 a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE
16、STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are avail
17、able online at http:/assist.daps.dla.mil/quicksearch/ or www.dodssp.daps.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited h
18、erein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum l
19、evels may degrade performance and affect reliability. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87748 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR
20、 97 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form,
21、 fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimens
22、ions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specifie
23、d on figure 1. 3.2.3 State diagram. The state diagram shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.5 Test circuit and switching waveforms. The test circuit and switching waveforms shall be as specified on figure 4. 3.3 Electrical pe
24、rformance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requireme
25、nts. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where markin
26、g of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535
27、. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PR
28、F-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be requi
29、red from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes
30、 Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendi
31、x A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this dra
32、wing. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer.
33、3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 33 (see MIL-PRF-38535, appendix A).Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWI
34、NG SIZE A 5962-87748 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Limits Test Symbol Conditions 1/ -55C TC +125C VCC= 5.0 V 10% unless otherwise specified Group A sub- groups Min Max Unit E5 M
35、TTL 0.5 V 2.4 V 0.5 V 0.5 V 0.5 V 0.5 V E4 MTTL 0.5 V 0.5 V 2.4 V 0.5 V 0.5 V 0.5 V E3 MECL 3.11 V 3.11 V 3.11 V 4.22 V 3.11 V 3.11 V E2 MECL 3.11V 3.11 V 3.11 V 3.11 V 4.22 V 3.11 V E1 MECL 3.11 V 3.11 V 3.11 V 3.11 V 3.11 V 4.22 V 1 4.03 4.22 E5 MTTL 0.5 V 2.4 V 0.5 V 0.5 V 0.5 V 0.5 V E4 MTTL 0.5
36、 V 0.5 V 2.4 V 0.5 V 0.5 V 0.5 V E3 MECL 3.14 V 3.14 V 3.14 V 4.37 V 3.14 V 3.14 V E2 MECL 3.14 V 3.14 V 3.14 V 3.14 V 4.37 V 3.14 V E1 MECL 3.14 V 3.14 V 3.14 V 3.14 V 3.14 V 4.37 V 2 4.1354.37 Output voltage high (prescaler) VOH12/ VEE= 0.0 V VCC= 5.0 V VCCO= 5.0 V See figure 2 E5 MTTL 0.5 V 2.4 V
37、 0.5 V 0.5 V 0.5 V 0.5 V E4 MTTL 0.5 V 0.5 V 2.4 V 0.5 V 0.5 V 0.5 V E3 MECL 3.04 V 3.04 V 3.04 V 4.12 V 3.04 V 3.04 V E2 MECL 3.04V 3.04 V 3.04 V 3.04 V 4.12 V 3.04 V E1 MECL 3.04 V 3.04 V 3.04 V 3.04 V 3.04 V 4.12 V 3 3.88 4.12 V E5 MTTL 0.5 V 2.4 V 0.5 V 0.5 V 0.5 V 0.5 V E4 MTTL 0.5 V 0.5 V 2.4
38、V 0.5 V 0.5 V 0.5 V E3 MECL 3.11 V 3.11 V 3.11 V 4.22 V 3.11 V 3.11 V E2 MECL 3.11 V 3.11 V 3.11 V 3.11 V 4.22 V 3.11 V E1 MECL 3.11 V 3.11 V 3.11 V 3.11 V 3.11 V 4.22 V 1 3.11 3.44 E5 MTTL 0.5 V 2.4 V 0.5 V 0.5 V 0.5 V 0.5 V E4 MTTL 0.5 V 0.5 V 2.4 V 0.5 V 0.5 V 0.5 V E3 MECL 3.14 V 3.14 V 3.14 V 4
39、.37 V 3.14 V 3.14 V E2 MECL 3.14 V 3.14 V 3.14 V 3.14 V 4.37 V 3.14 V E1 MECL 3.14 V 3.14 V 3.14 V 3.14 V 3.14 V 4.37 V 2 3.14 3.515 Output voltage low (prescaler) VOL12/ E5 MTTL 0.5 V 2.4 V 0.5 V 0.5 V 0.5 V 0.5 V E4 MTTL 0.5 V 0.5 V 2.4 V 0.5 V 0.5 V 0.5 V E3 MECL 3.04 V 3.04 V 3.04 V 4.12 V 3.04
40、V 3.04 V E2 MECL 3.04 V 3.04 V 3.04 V 3.04 V 4.12 V 3.04 V E1 MECL 3.04 V 3.04 V 3.04 V 3.04 V 3.04 V 4.12 V 3 3.04 3.405 V See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87748
41、 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Limits Test Symbol Conditions 1/ -55C TC +125C VCC= 5.0 V 10% unless otherwise specified Group A sub- groups Min MaxUnit Output voltag
42、e high (translator) VOH22/ VEE= 0.0 V VCC= 5.0 V MTTL Output = -0.4 mA VIHA(-) 3.895 V 4.000 V 3.745 V VIHB(-) 4.22 V 4.37 V 4.12 V VILA(+) 3.525 V 3.600 V 3.500 V VILB(+) 3.11 V 3.14 V 3.04 V 1 2 3 2.70 3.00 2.40 4.22 4.37 4.12 Output voltage low (translator) VOL22/ VEE= 0.0 V VCC= 5.0 V MTTL Outpu
43、t = 16 mA VIHA(-) 3.895 V 4.000 V 3.745 V VIHB(-) 4.22 V 4.37 V 4.12 V VILA(+) 3.525 V 3.600 V 3.500 V VILB(+) 3.11 V 3.14 V 3.04 V 1 2 3 0.10 0.10 0.10 0.80 0.66 1.00 V E5 MTTL 0.8 V 0.5 V 0.5 V 0.5 V 0.5 V 2.0 V 0.5 V 0.5 V 0.5 V 0.5 V E4 MTTL 0.5 V 0.8 V 0.5 V 0.5 V 0.5 V 0.5 V 2.0 V 0.5 V 0.5 V
44、0.5 V E3 MECL 3.11 V 3.11 V 3.525 V 3.11 V 3.11 V 3.11 V 3.11 V 3.895 V 3.11 V 3.11 V E2 MECL 3.11 V 3.11 V 3.11 V 3.525 V 3.11 V 3.11 V 3.11 V 3.11 V 3.895 V 3.11 V E1 MECL 3.11 V 3.11 V 3.11 V 3.11 V 3.525 V 3.11 V 3.11 V 3.11 V 3.11 V 3.895 V 1 4.01 4.22E5 MTTL 0.8 V 0.5 V 0.5 V 0.5 V 0.5 V 2.0 V
45、 0.5 V 0.5 V 0.5 V 0.5 V E4 MTTL 0.5 V 0.8 V 0.5 V 0.5 V 0.5 V 0.5 V 2.0 V 0.5 V 0.5 V 0.5 V E3 MECL 3.14 V 3.14 V 3.60 V 3.14 V 3.14 V 3.14 V 3.14 V 4.00 V 3.14 V 3.14 V E2 MECL 3.14 V 3.14 V 3.14 V 3.60 V 3.14 V 3.14 V 3.14 V 3.14 V 4.00 V 3.14 V E1 MECL 3.14 V 3.14 V 3.14 V 3.14 V 3.60 V 3.14 V 3
46、.14 V 3.14 V 3.14 V 4.00 V 2 4.115 4.37 Output voltage high (prescaler) VOHA2/ VEE= 0.0 V VCC= 5.0 V VCCO= 5.0 V See figure 2. E5 MTTL 0.8 V 0.5 V 0.5 V 0.5 V 0.5 V 2.0 V 0.5 V 0.5 V 0.5 V 0.5 V E4 MTTL 0.5 V 0.8 V 0.5 V 0.5 V 0.5 V 0.5 V 2.0 V 0.5 V 0.5 V 0.5 V E3 MECL 3.04 V 3.04 V 3.50 V 3.04 V 3
47、.04 V 3.04 V 3.04 V 3.745 V 3.04 V 3.04 V E2 MECL 3.04 V 3.04 V 3.04 V 3.50 V 3.04 V 3.04 V 3.04 V 3.04 V 3.745 V 3.04 V E1 MECL 3.04 V 3.04 V 3.04 V 3.04 V 3.50 V 3.04 V 3.04 V 3.04 V 3.04 V 3.745 V 3 3.86 4.12V See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networki
48、ng permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87748 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Limits Test Symbol Conditions 1/ -55C TC +125C VCC= 5.0 V 10% unless otherwise specified Group A sub- groups Min Max UnitE5 MTTL 0.8 V 0.5 V 0.5 V 0.5 V 0.5 V 2.0 V 0.5 V 0.5 V 0.5 V 0.5 V E5 MTTL 0.5 V 0.8 V 0.5 V 0.5 V 0.5 V 0.5 V 2.0 V 0.5 V 0.5 V 0.5 V E3 MECL 3.11 V 3.11 V 3.525 V 3.11 V 3.11 V 3.11 V 3.11 V 3.
