1、I ic SMD-5962-92263 REV A 9999996 O090200 hTO DEFENSE LOGISTICS AGENCY DEFENSE SUPPLY CENTER, COLUMBUS POST OFFICE BOX 3990 COLUMBUS, OH 43216-5000 IN REPLY REFER TO DSCC-VAC (Mr. T. Nguyen/(DSN)850-0671/6 14-692-067 l/tvn) NOV 13 l996 SUBJECT: Notice of Revision (NOR) 5962-RO27-97 for Standard Micr
2、ocircuit Drawing (SMD) 5962-92263 Militaryfindustry Distribution The enclosed NOR is approved for use effective as of the date of the NOR. In accordance with MIL-STD- 1 O0 SMD holders should, as a minimum, handwrite those changes described in the NOR to sheet 1 of the subject SMD. After completion,
3、the NOR should be attached to the subject SMD for future reference. Those companies who were listed as approved sources of supply prior to this action have agreed to actions taken on devices for which they had previously provided DSCC a certificate of compliance. This is evidenced by an existing act
4、ive current certificate of compliance on file at DSCC with a DSCC record of verbal coordination. The certificate of compliance for these devices is considered concurrence with the new revision unless DSCC is otherwise notified. If you have comments or questions, please contact Thanh Nguyen at (DSN)8
5、50-0671/(614)692-067 1. 1 Encl /MONICA L. POELKING Chief, Custom Microelectronics Team Federal Recycling Program Printed on Recycled Paper Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SUD-5962-92263 REV A 9999996 00902OL 537 m NOTICE OF REVISION (
6、NOR) THIS REVISION DESCRIBED BELOW HAS BEEN AUTHORIZED FOR THE DOCUMENT LISTED. Form Approved OM6 No. 0704-0188 b. ADDRESS (Street, City, State, Zip Code) 5. CAGE CODE 1. ORIGINATOR Defense Supply Center, Columbus 67268 UM repatina burdm foc mis dleclion is estimated to average 2 haip per respone in
7、dNing the time foc reviewing insitudons searching easting data sources ndudin su esbono for reduang this burden io Department of Defense Washingtion l!egeadguarten Seniices Diredorate SE DO NOT Rd%N COUR COIAPLETED FORM To EITHER OF THESE ADDRESSED. RETURN COMPLETED FORM TO THE GOMRNMENT weti and mi
8、nen2 ,me da$ eed. ytd mmpleng and rwimyng the cOiiecb add “A. Revisions description column; add “Changes in accordance with NOR 5962-R027-97“. Revisions date column; add “96-1 0-17“. Revision level block; add “A. Rev status of sheets; for sheets 1 and 6, add “A“. Table I, output short circuit curren
9、t, los; change maximum limit from “-225 mA“ to “-250 mA“. Revision level block; add “A. a 14. THIS SECTION FOR GOVERNMENT USE ONLY X (1) Existing document supplemented by the NOR may be used in manufacture. (2) Revised document must be received before manufacturer may incorporate this change. (3) Cu
10、stodian of master document shall make above revision and furnish revised document. b. ACTIVITY AUTHORIZED TO APPROVE CHANGE FOR GOVERNMENT DSCC-VAC DD Form 1695, APR 92 Previous editions are obsolete. c. TYPED NAME (First, Middle Initial, Last) Monica L. Poelking d. TITLE Chief, Custom Microelectron
11、ics Team 15a. ACTIVITY ACCOMPLISHING REVISION DSCC-VAC e. SIGNATURE f. DATE SIGNED (YYMMDD) 96-1 0-1 7 Monica L. Poelking b. REVISION COMPLETED (Signature) c. DATE SIGNED (YYMMDD) Thanh V. Nguyen 96-1 0-1 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS
12、-,-,-SND-59b2-92263 = 9999996 0064253 T27 H LTR REVISIONS I I I DESCRIPTION DATE (YR-MO-DA) APPROVED REV STATUS I REV III OF SHEETS SHEET PREPARED BY PMIC NIA CHECKED BY Thanh V. Nguyen STANDARD MICROCIRCUIT DRAWING APPROVED BY Monica L. Poelking I THIS DRAWING IS AVAILABLE FOR USE BY ALL UEPARTMENT
13、S AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 94- 10-06 AMSC N/A REVISION LEVEL I IESC FORM 193 JUL 91 DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 MICROCIRCUIT, DIGITAL, FAST CMOS, 16-BIT LATCHED TRANSCEIVER WITH THREE-STATE OUTPUTS, TTL COMPATIBLE INPUTS AND LIMITED OUT
14、PUT VOLTAGE SWING, MONOLITHIC SILICON SIZE I CAGE CODE A 67268 5962-92263 SHEET 1 OF 20 5962-E356-94 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SMD-5962-92263 9999
15、996 O064252 963 1.1 Scope. This drawing forms a part of a one part - one part number documentation system (see 6.6 herein). Two product assurance classes consisting of military high reliability (device classes Q and MI and space application (device class VI, and a choice of case outlines and lead fi
16、nishes are available and are refLected in the Part or Identifying Number (PIN). 1.2.1 of MIL-STD-883, “Provisions for the use of MIL-STD-883 in conjunction with compliant non-JAN devices“. available, a choice of Radiation Hardness Assurance (RHA) levels are reflected in the PIN. Device class M micro
17、circuits represent non-JAN class B microcircuits in accordance with When 1.2 m. The PIN shall be as shown in the following example: 5$ i 92263 RHA Devi ce Devi JI, ce 1 Case 1 Lead Federal stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see
18、 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device class M RHA marked devices shall meet the MIL-1-38535 appendix A specified RHA levels and shall be marked with the appropriate RHA designator. MIL-1-38535 specified RHA levels and shall be marked with the appropriate RHA designator.
19、 non-RHA device. Device classes Q and V RHA marked devices shall meet the A dash (-1 indicates a SIZE STANDARI) A MICROCIRCUIT DRAWING DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 1.2.2 Device tvpe(s). The device type(s) shall identify the circuit function as follows: Device type Generic num
20、ber Circuit function 5962-92263 REVISION LEVEL SHEET 2 o1 54FCT16543T 16-bit latched transceiver with three-state outputs, TTL compatible inputs and limited output voltage swing 02 54FCT16543AT lbbit latched transceiver with three-state outputs, TTL compatible inputs and limited output voltage swing
21、 03 54FCT16543CT 16-bit latched transceiver with three-state outputs, TTL compatible inputs and limited output voltage swing 1.2.3 Device class desisnator. The device class designator shall be a single letter identifying the product assurance level as follows: Device class Device requirements docume
22、ntation M Vendor self-certification to the requirements for non-JAN class B microcircuits in accordance with 1.2.1 of MIL-STD-883 Q or V Certification and qualification to MIL-1-38535 1.2.4 Case outline(s1. The case outline(s1 shall be as designated in MIL-STD-1835, and as follows: Out line letter D
23、escriptive desisnator Termi na 1s Package style X GDFPl-FS6 56 Flat pack 1.2.5 Lead finish. The lead finish shall be as specified in MIL-STD-883 (see 3.1 herein) for class M or MIL-1-38535 for classes Q and V. designation is for use in specifications when lead finishes A, 8, and C are considered acc
24、eptable and interchangeable without preference. Finish letter “X“ shall not be marked on the microcircuit or its packaging. The “X“ DESC FORM 193A JUL 91 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SMD-5962-72263 9999996 0064253 BTT I 1.3 Absolut
25、e maximum ratinss. I/ g/ 3/ Supply voltage range (V - - - - - - - - - - - - - - - - - - DC input voltage range hIN) - - - - - - - - - - - - - - - - - DC output voltage range (Vo - - - - - - - - - - - - - - - - DC input clamp current (i,) (VIN = -0.5 V - - - - - - - - - DC output clamp current (IOK)
26、(VOUT -0.5 V and +7.0 VI - - - - DC output source current (I - - - - - - - - - DC output sink current (IOL?“(per output) - - - - - - - - - - Grouns current (IGND) - - - - - - - - - - - - - - - - - - - - Storage temperature range (T - - - - - - - - - - - - - - - Case temperature under bias If - - - -
27、 - - - - - - - - - Lead temperature (soldering, Ifl%conds) - - - - - - - - - - - Thermal resistance, junction-to-case (OJc) - - - - - - - - - - Junction temperature (TJ) - - - - - - - - - - - - - - - - - - Maximum power dissipation (PD) - - - - - - - - - - - - - - - - (per output) DC Vc current (Icc
28、) - - - - - - - - - - - - - - - - - 1.4 Recommended operating conditions. 2/ I/ Supply voltage range Wee) - - - - - - - - - - - - - - - - - - Input voltage range (VIN) - - - - - - - - - - - - - - - - - - Output voltage range (VOUT) - - - - - - - - - - - - - - - - - Maximum tow level input voltage (V
29、IL) - - - - - - - - - - - - Minimum high level input voltage (VI,) - - - - - - - - - - - - Case operating temperature range (T ) - - - - - - - - - - - - Maximum input rise or fall rate (AtSAv): - - - - - - - - Maximum high level output current (Io - - - - - - - - - - - Maximum low level output curre
30、nt (+,J - - - - - - - - - - - - (from VIN = 0.3 V to 2.7 V, 2.7 V to 0.3 VI -0.5 V dc to +7.0 V dc -0.5 V dc to Vcc + 0.5 V dc -0.5 V dc to Vcc -20 nA i20 mA -30 mA +70 mA I480 mA +I120 mA 4/ -65OC to +150“C -65OC to +13SoC +3m0 c See MIL-STD-1835 +175c 1.0 u +4.5 V dc to +5.5 V dc +O.O V dc to Vcc
31、+O.O V dc to Vcc 0.8 V 2.0 v -55OC to +125C 2.5 ns/V -24 mA 48 mA 1.5 Digital logic testinq for device classes Q and V. Fault coverage measurement of manufacturing logic tests (MIL-STD-883, test method 5012) - - - - - - - - XX percent s/ 2. APPLICABLE DOCUMENTS 2.1 Government specification, standard
32、s, bulletin, and handbook. Unless otherwise specified, the following specification, standards, bulletin, and handbook of the issue listed in that issue of the Department of Defense Index of Specifications and Standards specified in the solicitation, form a part of this drawing to the extent specifie
33、d herein. - I/ Stresses above the absolute maximum rating may cause permanent damage to the device. maximum levels may degrade performance and affect reliability. Unless othervise noted, all voltages are referenced to GND. The limits for the parameters specified herein shall apply over the full spec
34、ified Vcc range and case temperature range of -55C to +125OC. - 4/ For Vcc 2 6.5 V, the upper limit on the range is limited to 7.0 V. - 5/ Values will be added when they become available. Extended operation at the - 2/ - 31 STANDARD 5962-92263 MICROCIRCUIT DRAWING DEFENSE ELECTRONICS SUPPLY CENTER D
35、AYTON, OHIO 45444 DESC FORM 193A JUL 91 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SPECIFICATION MILITARY MIL-1-38535 STANDARDS MILITARY MIL-STD-883 MIL-STD-973 MIL-STD-1835 BULLETIN MILITARY MIL-BUL-103 HANDBOOK MILITARY M IL-HDBK-780 SMD-5962-
36、72263 = ib 0064254 736 = Integrated Circuits, Manufacturing, General Specification for. Test Methods and Procedures for ilicroelectronics. Configuration Nanagement. Microcircuit Case Outlines List of Standardized Military Drawings (SHDs). Standardized Military Drawings. (Copies of the specification,
37、 standards, bulletin, and handbook required by manufacturers in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting activity.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the re
38、ferences cited herein, the text of this drawing shall take precedence. 3. REQUIREMENTS 3.1 The individual item requirements for device class i shall be in accordance with 1.2.1 of MIL-STD-883, Provisions for the use of MIL-STD-883 in conjunction with compliant non-JAN devices“ and as specified herei
39、n. device manufacturers Quality Management (QM) plan, and as specif ied herein. Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-1-38535, the 3.2 Desian, construction, and physical dimensions. The design, construction, and physical dimens
40、ions shall be as specified in MIL-STD-883 (see 3.1 herein) for device class M and MIL-1-38535 for device classes (;I and V and herein. 3.2.1 Case outline. The case outline shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. 3.2.3 Truth table. 3.2.4 Loqic diaqram. 3.2.5 Ground bounc
41、e load circuit and waveforms. The terminal connections shall be as specified on figure I. The truth table shall be as specified on figure 2. The logic diagram shall be as specified on figure 3. The ground bounce load circuit and waveforms shall be as Specified on figure 4. 3.2.6 Switching waveforms
42、and test circuit. The switching waveforms and test circuit shall be as specified on figure 5. 3.3 E lectr i cal performance character i st i cs and postirradiation parameter limits. Unless otherwise Spec? f ied herein, the electrical performance characteristics and postirradiation parameter limits a
43、re as specified in table I and shall apply over the full case operating temperature range. and limits are as specified in table I. 3.4 Electrical test requirements. Test conditions for these specified characteristics The electrical test requirements shall be the subgroups specified in table II. The
44、electrical tests for each subgroup are defined in table I. STANDARD MICROCIRCUIT DRAWING I YE I I 5962-92263 I DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 I REVISION LEVEL SHEET 14 DESC FORM 193A JUL 91 Provided by IHSNot for ResaleNo reproduction or networking permitted without license fro
45、m IHS-,-,-. SIZE STANDARD A SMD-5962-92263 7b 00642.55 b72 5962-92263 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. Marking for device class M shall be in accordance with MIL-STD-883 (see 3.1 herein). MIL-BUL-103. In addition, the manufacturers PIN may also be marked as li
46、sted in Marking for device classes Q and V shall be in accordance with MIL-1-38535. 3.5.1 Certification/complisnce mark. The compliance mark for device class M shall be a “C“ as required in MIL-STD-883 (see 3.1 herein). in MIL-1-38535. The certification mark for device classes Q and V shall be a “QM
47、L“ or “QI as required 3.6 Certificate of compliance. For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-BUL-103 (see 6.7.2 herein). classes Q and V, a certificate of compliance shall be required from a QM
48、L-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.7.1 herein). listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device class PI the requirements of MIL-STD-883 (see 3.1 herein), or for device class
49、es Q and V, the requirements of MIL-1-38535 and the requirements herein. For device The certificate of compliance submitted to DESC-Et prior to 3.7 Certificate of conformance. A certificate of conformance as required for device class M in MIL-STD-883 (see 3.1 herein) or for device classes Q and V in MIL-1-38535 shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of chanqe for device cla
