1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with NOR 5962-R148-95. 95-05-25 K. A. Cottongim B Add note to table II. Update drawing boilerplate. Editorial changes throughout. 03-06-19 Raymond Monnin C Added footnote 2 to table II, under group C end-point electricals. U
2、pdated drawing paragraphs. -sld 12-07-12 Greg Cecil REV SHEET REV SHEET REV STATUS REV C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 PMIC N/A PREPARED BY Steve Duncan DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil/ STANDARD MICROCIRCUIT DRAWING CHECKED B
3、Y Mike Jones THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Kendall A Cottongim MICROCIRCUIT, HYBRID, LINEAR, ANALOG MULTIPLEXER AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 93-11-23 AMSC N/A REVISION LEVEL C SIZE A CAGE CODE 67268 5962-94506 SHEET 1 OF 10 DSCC F
4、ORM 2233 APR 97 5962-E265-12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94506 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawi
5、ng documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the
6、 PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 94506 01 H X X Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardness
7、assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic numb
8、er Circuit function 01 MX-826/883 Analog multiplexer 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class
9、 H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military quality class level. This level is intended for us
10、e in applications where non-space high reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified incoming flow, and the manufac
11、turer guarantees (but may not test) periodic and conformance inspections (Group A, B, C, and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the device acquisition d
12、ocument; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may have a limited tempe
13、rature range. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94506 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 97 1.2.4 Case outline(s). The case outline(s) ar
14、e as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X See figure 1 24 Dual-in-line 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Positive supply voltage range (VCC) . -0.3 V dc to
15、+18 V dc Negative supply voltage range (VEE) +0.3 V dc to -18 V dc Logic supply voltage range (VDD) . -0.3 V dc to +7 V dc Analog input voltage (pins 4 - 11) VCC- VEEDigital input voltage range (pins 1, 2, and 3) -0.5 V dc to +5.5 V dc Output current (short to common) 50 mA Storage temperature -65 C
16、 to +150 C Power dissipation (PD), (TC= +125 C) . 600 mW Lead temperature (soldering, 10 seconds) +300 C Junction temperature (TJ) +175 C Thermal resistance: Junction-to-case (qJC) . 12 C/W Junction-to-ambient (qJA) 53 C/W 1.4 Recommended operating conditions. Positive supply voltage range (VCC) . +
17、14.5 V dc to +15.5 V dc Negative supply voltage range (VEE) . -14.5 V dc to -15.5 V dc Logic supply voltage range (VDD) . +4.5 V dc to +5.5 V dc Case operating temperature range (TC). -55 C to +125 C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specif
18、ication, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybrid Microcircuits, General Specification for
19、. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies
20、of these documents are available online at https:/dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 1/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the ma
21、ximum levels may degrade performance and affect reliability. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94506 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 4 DSCC FORM 2234 APR 9
22、7 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREME
23、NTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 may include the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) p
24、lan or as designated for the applicable device class. Therefore, the tests and inspections herein may not be performed for the applicable device class (see MIL-PRF-38534). Furthermore, the manufacturer may take exceptions or use alternate methods to the tests and inspections herein and not perform t
25、hem. However, the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case
26、 outline(s) shall be in accordance with 1.2.2 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in tab
27、le I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marking of device(s) sha
28、ll be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein
29、shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall b
30、e maintained under document revision level control by the manufacturer and be made available to the preparing activity (DLA Land and Maritime -VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The ce
31、rtificate of compliance (original copy) submitted to DLA Land and Maritime -VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with
32、each lot of microcircuits delivered to this drawing. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94506 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 TABLE
33、I. Electrical performance characteristics. Test Symbol Conditions 1/ -55 C TC +125 C unless otherwise specified Group A subgroups Device type Limits Unit Min Max QUIESCENT SUPPLY CURRENT Positive supply ICCVCC= +15.0 V, pins 12, 17, 18, and 23 = ground 1, 2, 3 01 +21 mA Negative supply IEEVEE= -15.0
34、 V, pins 12, 17, 18, and 23 = ground 1, 2, 3 01 -21 mA Logic supply IDDVDD= +5.0 V, pins 12, 17, 18, and 23 = ground 1, 2, 3 01 +1 mA Power dissipation PDVCC= +15 V, VEE= -15, and VDD= +5 V 1, 2, 3 01 600 mW Power supply rejection ratio PSRR VEE VDD VCC4, 5, 6 01 85 dB DIGITAL INPUTS Input voltage h
35、igh, Logic 1 VIHVDD= +5 V, pins 12, 17, 18, and 23 = ground 1, 2, 3 01 2.0 V Input voltage low, Logic 0 VILVDD= +5 V, pins 12, 17, 18, and 23 = ground 1, 2, 3 01 0.8 V LOGIC LOADING Input current high, Logic “1“ IILVDD= +5 V, pins 12, 17, 18, and 23 = ground 1, 2, 3 01 1.0 mA Input current low, Logi
36、c “0“ IIHVDD= +5 V, pins 12, 17, 18, and 23 = ground 1, 2, 3 01 1.0 mA ANALOG INPUT Input voltage range VINVCC= +15 V, VEE= -15 V, and VDD= +5 V 1, 2, 3 01 -10 +10 V Input impedance IZVCC= +15 V, VEE= -15 V, and VDD= +5 V 1, 2, 3 01 2.45 2.55 kW ANALOG OUTPUT Output voltage range VOUTVCC= +15 V, VEE
37、= -15 V, and VDD= +5 V 1, 2, 3 01 -10 +10 V Output current IOUTVCC= +15 V, VEE= -15 V, and VDD= +5 V, TC= +25 C 1 01 15 mA Offset voltage VOFFVCC= +15 V, VEE= -15 V, and VDD= +5 V 1 01 0.5 mV 2, 3 1.5 Gain error AEVCC= +15 V, VEE= -15 V, and VDD= +5 V, TC= +25 C 4 01 -.03 +.03 %FS Gain error tempera
38、ture coefficient DAE DT VCC= +15 V, VEE= -15 V, and VDD= +5 V 5, 6 01 -.5 +.5 PPM / C Cross talk 2/ CT VCC= +15 V, VEE= -15 V, and VDD= +5 V, f = 100 kHz 7 01 -82 dB 8A -83 8B -94 VCC= +15 V, VEE= -15 V, and VDD= +5 V, f = 1 MHz 7 -64 8A -75 8B -82 See footnotes at end of table. Provided by IHSNot f
39、or ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94506 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Condit
40、ions 1/ -55 C TC +125 C unless otherwise specified Group A subgroups Device type Limits Unit Min Max BANDWIDTH Small signal (3 dB) 2/ BW VCC= +15 V, VEE= -15 V, and VDD= +5 V 7, 8 01 8 MHz Full power bandwidth 2/ FPBW VCC= +15 V, VEE= -15 V, and VDD= +5 V 7, 8 01 3 MHz SWITCHING CHARACTERISTICS Brea
41、k before make interval 2/ TOPENVCC= +15 V, VEE= -15 V, and VDD= +5 V 9, 10, 11 01 25 ns Turn on 2/ TONVCC= +15 V, VEE= -15 V, and VDD= +5 V 9, 10, 11 01 50 ns Turn off 2/ TOFFVCC= +15 V, VEE= -15 V, and VDD= +5 V 9, 10, 11 01 50 ns Output slew rate 2/ SRVCC= +15 V, VEE= -15 V, and VDD= +5 V 7 01 250
42、 V/ms Output settling time, 2/ .1% (10 volt step) .1% (20 volt step) .01% (10 volt step) .01% (20 volt step) .003% (10 volt step) .003% (20 volt step) ST1 VCC= +15 V, VEE= -15 V, and VDD= +5 V, TC= +25 C, 500W load 7 01 150 ns ST2 VCC= +15 V, VEE= -15 V, and VDD= +5 V, 1 kW load 8A, 8B 280 ns ST3 VC
43、C= +15 V, VEE= -15 V, and VDD= +5 V, TC= +25 C, 500W load 7 225 ns ST4 VCC= +15 V, VEE= -15 V, and VDD= +5 V, 1 kW load 8A, 8B 390 ns ST5 VCC= +15 V, VEE= -15 V, and VDD= +5 V, TC= +25 C, 500W load 7 400 ns ST6 VCC= +15 V, VEE= -15 V, and VDD= +5 V, 1 kW load 8A, 8B 740 ns 1/ Unless otherwise specif
44、ied the following conditions apply: VCC= +15.0 V dc, VEE= -15.0 V dc, VDD= +5.0 V dc, Logic “0“ = VIL= +0.8 V dc, Logic “1“ = VIH=+2.0 V dc, VFSR = 20 V 2/ Guaranteed to the limits specified in table I if not tested. Provided by IHSNot for ResaleNo reproduction or networking permitted without licens
45、e from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94506 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 Case outline X. Symbol Millimeters Inches Min. Max. Min. Max. A 5.99 .236 A1 3.05 5.08 .120 .200 A2 4.06 5.46 .160 .215 A3 4.70 6.35 .185 .250
46、 b 0.41 0.56 .016 .022 c 0.23 0.38 .009 .015 D 32.39 35.18 1.275 1.385 e 2.54 BSC .100 BSC e1 0.89 1.14 .035 .045 E 19.56 21.08 .770 .830 EA 14.99 15.49 .590 .610 Q 0.38 1.14 .015 .045 S 2.16 3.18 .085 .125 NOTES: 1. The U.S. preferred system of measurement is the metric SI. This item was designed u
47、sing inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. Pin number identification is for reference only. FIGURE 1. Case outline(s). Provided by IHSNot for ResaleNo reproduction or networking permitted
48、without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94506 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 8 DSCC FORM 2234 APR 97 Device type 01 Case outline X Terminal number Terminal symbol 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 A0 A1 A2 IN1 IN2 IN3 IN4 IN5 IN6 IN7 IN8 GR
