1、BRITISH STANDARDBS EN 13032-3:2007Measurement and presentation of photometric data of lamps and luminaires Part 3: Presentation of data for emergency lighting of work placesThe European Standard EN 13032-3:2007 has the status of a British StandardICS 17.180.20; 29.140.40; 91.160.10g49g50g3g38g50g51g
2、60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 13032-3:2007This British Standard was published under the authority of the Standards Policy and Strategy Committ
3、ee on 30 November 2007 BSI 2007ISBN 978 0 580 54776 8National forewordThis British Standard is the UK implementation of EN 13032-3:2007. It supersedes BS 5225-3:1982 which is withdrawn. The UK participation in its preparation was entrusted by Technical Committee CPL/34, Lamps and related equipment,
4、to Subcommittee CPL/34/9, Emergency lighting.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a
5、British Standard cannot confer immunity from legal obligations.Amendments issued since publicationAmd. No. Date CommentsEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 13032-3October 2007ICS 17.180.20; 91.160.10English VersionMeasurement and presentation of photometric data of lampsand luminaires
6、- Part 3: Presentation of data for emergencylighting of work placesLumire et clairage - Mesure et prsentation des donnesphotomtriques des lampes et des luminaires - Partie 3:Prsentation des donnes pour lclairage de scurit deslieux de travailLicht und Beleuchtung - Messung und Darstellungphotometrisc
7、her Daten von Lampen und Leuchten - Teil 3:Darstellung von Daten fr die Notbeleuchtung vonArbeitsstttenThis European Standard was approved by CEN on 26 August 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandar
8、d the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, Ge
9、rman). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Re
10、public, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE N
11、ORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13032-3:2007: EEN 13032-3:2007 (E) 2 Contents Page Foreword. 3 Introduction 4 1 Sco
12、pe 5 2 Normative references . 5 3 Terms and definitions. 5 4 Essential lamp data. 6 5 Luminaire data. 7 5.1 Essential luminaire data. 7 5.1.1 Luminaire code 7 5.1.2 Normalized intensity table 7 5.1.3 Luminaire maintenance factors (LMF) 8 5.1.4 Luminaire service correction factors (LSCF)- all data sh
13、all be declared 8 5.2 Useful luminaire data 8 5.2.1 Physical dimensions of the luminaire. 8 5.2.2 Intensity diagram 8 5.2.3 Spacing tables. 8 Annex A (informative) Illuminance calculation on a horizontal plane from a point source 9 Bibliography . 10 EN 13032-3:2007 (E) 3 Foreword This document (EN 1
14、3032-3:2007) has been prepared by Technical Committee CEN/TC 169 “Light and lighting”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2008, and conf
15、licting national standards shall be withdrawn at the latest by April 2008. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According t
16、o the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lit
17、huania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 13032-3:2007 (E) 4 Introduction This standard is to be used in conjunction with EN 13032-1. Emergency lighting is required by National Regulations in a
18、 number of European countries. This standard specifies the required data for emergency lighting as required by EN 1838. For the application of this document the terms according to IEC 60050 also applies. EN 13032-3:2007 (E) 5 1 Scope This standard specifies the required data for lamps and luminaires
19、 to verify conformity with EN 1838. This standard does not define the data requirements for signage, as these can be found in EN 1838. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applie
20、s. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 13032-1, Light and lighting - Measurement and presentation of photometric data of lamps and luminaires - Part 1: Measurement and file format 3 Terms and definitions For the purposes of thi
21、s European Standard, the following terms and definitions apply. NOTE This clause defines terms and quantities that are in use and important to this standard, and which may not be given in IEC 60050. 3.1 correction factor factor to modify the luminaire data as presented on a particular photometric da
22、ta sheet to those of similar luminaires (for example: Ballast Lumen Factor, length, lumen corrections) 3.2 essential data lamp and luminaire data required for the verification of conformity to the requirements of EN 1838 3.3 lamp code any combination of letters and numbers by which the lamp type is
23、identified 3.4 lamp dimensions all dimensions of the lamp that are relevant for the luminaire 3.5 luminaire code any combination of letters and numbers by which the luminaire type is identified 3.6 nominal lamp wattage (Wlamp) approximate wattage used to designate or identify the lamp NOTE The nomin
24、al lamp wattage is also (incorrectly) known as rated lamp wattage. 3.7 useful data lamp and luminaire data beneficial to the designers and users in the planning and operation of lighting installations EN 13032-3:2007 (E) 6 3.8 emergency ballast lumen factor (EBLF) ratio of the luminous flux of the l
25、amp supplied by the emergency ballast to the luminous flux of the same lamp operated with the appropriate reference ballast at its rated voltage and frequency. The emergency ballast lumen factor is the minimum of the values measured at the appropriate time after failure of the normal supply and cont
26、inuously to the end of the rated time EBLF = BLF FTIME (1) 3.9 FTIMEminimum light output values measured during the emergency operating time period 3.10 practical emergency lamp flux (PELF) lowest luminous flux of the lamp observed during the rated duration of the emergency mode PELF = LDL EBLF (2)
27、where LDL is the initial lighting design lumens at 100 h as declared by the manufacturer 4 Essential lamp data The following lamp data shall be provided for verification: a) lamp code; b) lamp dimensions; c) luminous flux (LDL); d) lamp lumen maintenance factor (LLMF); NOTE 1 The lamp lumen maintena
28、nce factor may be presented both as a graph or data in a table. However, to allow the designer to set up an optimal maintenance scheme, it is recommended to present these data in tabular form. e) lamp survival factor (LSF); NOTE 2 The lamp survival factor may be presented as a graph or as data in a
29、table. However, to allow the designer to set up an optimal maintenance scheme, it is recommended to present these data in tabular form. f) general colour rendering index (Ra); g) nominal lamp wattage (Wlamp). EN 13032-3:2007 (E) 7 5 Luminaire data 5.1 Essential luminaire data 5.1.1 Luminaire code 5.
30、1.2 Normalized intensity table The tabulated luminous intensity values normalized to a total bare lamp flux in the luminaire of 1 000 lm shall be given in cd.klm-1. The light intensity shall be declared for an ambient temperature of 25 C and nominal voltage of the emergency ballast and measured in a
31、ccordance with EN 13032-1. It shall take into account the thermal behaviour of the lamp in the luminaire due to the temperature generated by all the components inside the luminaire. An appropriate thermal correction factor shall be applied if the luminous intensity has been measured in other conditi
32、ons e.g. with another ballast. These values (cd/1 000 lm) permit calculation of the Light Output Ratio (LOR) of the luminaire. For luminaires with multiples lamps where light intensity distribution of the luminaire can be different when not all lamps are operated in the emergency mode, the distribut
33、ion for emergency mode shall be reported. The number of C-planes and -angles at which the I-values shall be specified, is given in Table 1 and Table 2. Table 1 Number of C-planes for various intensity distributions Luminous intensity distribution C-planes Escape routes only Radially symmetric One C-
34、plane 0 and 90 Symmetric about two planes Every 15 from 0 to 90 0 and 90 Symmetric about one plane Every 15 from 0 to 180 or every 15 from 90 to 270 0 and 90 Asymmetric Every 15 from 0 to 360 0 and 90 Table 2 Number of -angles for various types of luminaires Type of luminaire Downward Flux Fraction
35、(DFF) -angles Downlighting 0,9 Every 5 from 0 to 90 Downlighting with upward component 0,1 to 0,9 Every 5 from 0 to 180 Uplighting 0,1 Every 5 from 90 to 180 For floodlights used in indoor and/or outdoor lighting installations, the measurement and presentation of the normalised I-table may be in B-
36、instead of C- notation. NOTE Luminaires with a concentrated intensity distribution may require more angles at which the luminous intensity data are presented (e.g. every 1 in the area where 90 % of the luminous flux is emitted). EN 13032-3:2007 (E) 8 5.1.3 Luminaire maintenance factors (LMF) All dat
37、a shall be declared. NOTE The luminaire maintenance factor (LMF) may be presented as a graph or as data in a table. However, to allow the designer to set up an optimal maintenance scheme, it is recommended to present these data in tabular form. 5.1.4 Luminaire service correction factors (LSCF)- all
38、data shall be declared 5.1.4.1 Temperature correction if operated in an ambient other than 25 oC. 5.1.4.2 Cable voltage correction factor (central systems) for luminaires operating at voltages other than rated voltage. 5.2 Useful luminaire data 5.2.1 Physical dimensions of the luminaire The physical
39、 dimensions, which are basically the length and width or diameter of the luminaire and its height, shall be provided. 5.2.2 Intensity diagram The intensity distribution shall be presented as a graph and is mainly intended to provide a first impression of the shape of the luminous intensity distribut
40、ion. The graph may be in any form (e.g. polar, Cartesian, etc.). 5.2.3 Spacing tables If pre-calculated spacing of the luminaires is provided by the manufacturer, all correction factors and assumptions shall be declared (see Annex A). NOTE 1 For uplighting, the ceiling can be treated as part of the
41、luminaire for the first reflection. NOTE 2 The Downward Flux Fraction (DFF) is the ratio of the Downward Light Output Ratio (DLOR) and the Light Output Ratio (LOR) of the luminaire: DFF = DLOR/LOR. EN 13032-3:2007 (E) 9 Annex A (informative) Illuminance calculation on a horizontal plane from a point
42、 source Figure A.1 Illuminance curves show the variation of illuminance along a straight line, these curves can be produced for a particular height or they may be produced as relative diagrams with the distance from the light source expressed in terms of the mounting height (h). The horizontal illum
43、inance at point P on the floor is given by the following formula: ycosycos32cy2cyphldlE = (A.1) where LSFLMFLLMF1000PELFnormalizedcycy= II (A.2) E is the horizontal illuminance at point P (lux); Iis the intensity from the luminaire at elevation and azimuth (candelas); h is the height of the luminair
44、e above the floor (metres); d is the distance from the luminaire to point P (metres); y is the angle between the downward vertical and point P at the centre of the luminaire; c is the horizontal plane; is the vertical plane. EN 13032-3:2007 (E) 10 Bibliography 1 EN 1838:1999, Lighting applications E
45、mergency lighting. 2 EN 12464-1:2002, Light and lighting Lighting of work places Part 1: Indoor work places. 3 EN 12464-2, Light and lighting - Lighting of work places - Part 2: Outdoor work places. 4 EN 12665:2002, Light and Lighting Basic terms and criteria for specifying lighting requirements. 5
46、EN 50172:2004, Emergency escape lighting systems. 6 EN 60598-2-22:2002, Luminaires - Part 2-22: Particular requirements - Luminaires for emergency lighting (IEC 60598-2-22:1997, modified). 7 IEC 60050-845:1987, International Electrotechnical Vocabulary Chapter 845: Lighting. 8 IEC 61347-2-7:2000, La
47、mp controlgear Part 2-7: Particular requirements for d.c. supplied electronic ballasts for emergency lighting (IEC 61347-2-7:2006). 9 The Construction Products Directive (89/106) 10 The Workplace Directive (89/654) 11 The Signs Directive (90/664) blankBS EN 13032-3:2007BSI389 Chiswick High RoadLondo
48、nW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision
49、. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fa
