1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationResilient floor coverings Semi-flexible/vinylcomposition (VCT) poly(vinyl chloride) floor tiles SpecificationBS EN ISO 10595:2012Incorporating corrigendum October 2012National fo
2、rewordThis British Standard is the UK implementation of EN ISO 10595:2012,The UK participation in its preparation was entrusted to Technical Committee PRI/60, Resilient floor coverings.A list of organizations represented on this committee can be obtained on request to its secretary.This publication
3、does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2013.Published by BSI Standards Limited 2013 ISBN 978 0 580 81235 ICS 97.150Compliance with a British Standard cannot confer immunity from lega
4、l obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 29 February 2012.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN ISO 10595:2012incorporating corrigendum October 2012. It is identical to ISO
5、10595:2010.4Implementation of CEN corrigendum October 2012: Supersession information updatedIt supersedes BS EN 654:2011, which is withdrawn.30 April 2013EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 10595 February 2012 ICS 97.150 English Version Resilient floor coverings - Semi-flexible/
6、vinylcomposition (VCT) poly(vinyl chloride) floor tiles - Specification (ISO 10595:2010) Revtements de sol rsilients - Carreaux semi-flexibles/vinyle (VCT) en poly(chlorure de vinyle) - Spcifications (ISO 10595:2010) Elastische Bodenbelge - Halbflexible PVC-Bodenplatten -Spezifikation (ISO 10595:201
7、0) This European Standard was approved by CEN on 31 December 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical
8、 references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of
9、 a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungar
10、y, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management
11、 Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 10595:2012: EIncorporating corrigendum October 20123 Foreword The text of ISO 10595:2010 has been prepared by Technical Committee I
12、SO/TC 219 “Floor coverings” of the International Organization for Standardization (ISO) and has been taken over as EN ISO 10595:2012 by Technical Committee CEN/TC 134 “Resilient, textile and laminate floor coverings” the secretariat of which is held by BSI. This European Standard shall be given the
13、status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2012, and conflicting national standards shall be withdrawn at the latest by August 2012. Attention is drawn to the possibility that some of the elements of this document may be the s
14、ubject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium,
15、 Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endor
16、sement notice The text of ISO 10595:2010 has been approved by CEN as a EN ISO 10595:2012 without any modification. This document supersedes EN 654:2011 and consequently EN 654:2011 is withdrawnBS EN ISO 10595:2012 EN ISO 10595:2012 (E).INTERNATIONAL STANDARD ISO 201 1Resilient floor coverings Semi-f
17、lexible/vinylcomposition (VCT) poly(vinyl chloride) floor tiles Specification 1 Scope This International Standard specifies the characteristics of semi-flexible/vinyl composition floor tiles based on poly(vinyl chloride) (PVC) binder and supplied in tile form. Products may contain a transparent, non
18、-PVC factory finish. To encourage the consumer to make an informed choice, this International Standard includes a classification system (see ISO 10874) based on the intensity of use, which shows where these floor coverings give satisfactory service. It also specifies requirements for marking. 2 Norm
19、ative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 10874, Resilient, textile an
20、d laminate floor coverings Classification ISO 24340, Resilient floor coverings Determination of thickness of layers ISO 24342, Resilient and textile floor-coverings Determination of side length, edge straightness and squareness of tiles ISO 24343-3, Resilient and laminate floor coverings Determinati
21、on of indentation and residual indentation Part 3: Resilient semi-flexible/vinyl composition tiles: Indentation ISO 24344:2008, Resilient floor coverings Determination of flexibility and deflection ISO 24346, Resilient floor coverings Determination of overall thickness ISO 23999, Resilient floor cov
22、erings Determination of dimensional stability and curling after exposure to heat ASTM F1265, Standard Test Method for Resistance to Impact for Resilient Floor Tile 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 poly(vinyl chloride) floor cov
23、erings floor covering produced using poly(vinyl chloride) as a binder 2BS EN ISO 10595:2012 EN ISO 10595:2012 (E)2 ISO 20123.2 semi-flexible floor tiles rigid tiles made from poly(vinyl chloride) which can only be deflected under specified conditions 3.3 vinyl composition tile resilient floor coveri
24、ng composed of a poly(vinyl chloride) binder, filler and pigments NOTE The binder shall consist of one or more resins of poly(vinyl chloride) and/or copolymers of vinyl chloride compounded with suitable plasticizers and stabilizers. Other suitable polymeric resins may be incorporated as part of the
25、binder. 3.4 solid-colour tile tile with a uniform single colour throughout its entire thickness 3.5 through-pattern tile tile where either the pattern and colours on the surface of the tile extend entirely through the thickness of the tile without significant change, or the colours appearing on the
26、surface extend throughout the entire thickness of the tile, although the appearance of the pattern created by these colours will change throughout the thickness 3.6 surface-pattern tile tile where the decoration or pattern need not extend throughout the entire thickness NOTE The combination of patte
27、rn and wear surface must exceed 0,1 mm or as otherwise specified in Table 3. 3.7 factory finish transparent coating applied during the manufacture 4 Requirements 4.1 Identification requirements Floor tiles described in this International Standard shall be non-asbestos formulated and identified by co
28、nstruction as shown in Table 1. Table 1 Identification by construction Type Construction I Solid colour II Through pattern III Surface pattern 4.2 General requirements Floor tiles described in this International Standard shall conform to the appropriate general requirements specified in Table 2 when
29、 tested in accordance with the methods given therein. BS EN ISO 10595:2012 EN ISO 10595:2012 (E) ISO 201 3Table 2 General requirements Characteristic/Property Requirement Test method Overall thickness mm Nominal value 0,13 ISO 24346 Tiles: side length mm squareness and straightness mm for side lengt
30、h u 305 mm 305 mm Deviation u 0,13 % of nominal length up to 0,4 mm maximum Deviation allowed at any point u 0,25 u 0,35 ISO 24342 Dimensional stability after exposure to heat % u 0,20 ISO 23999 Impact u 2,5 mm thick 4 drops from 250 mm 2,5 mm thick 4 drops from 500 mm No cracks beyond limit ASTM F1
31、265 Flexibility mm W 25 ISO 24344:2008, Method B Indentation resistance mm Indentation, IRat 25 C 0,25 C 0,15 IRu 0,40 ISO 24343-3 5 Classification The classification scheme for resilient floor coverings is described in ISO 10874. The requirements for use of semi-flexible/vinyl composition poly(viny
32、l chloride) floor tile in accordance with this scheme are specified in Table 3. 2BS EN ISO 10595:2012 EN ISO 10595:2012 (E)4 ISO 2012Table 3 Classification requirement for level of use Overall thickness Thickness of wear layer Class Symbol Intensity of use Minimum nominal value, mm Minimum nominal v
33、alue, mm All types Applies to Type III onlyDomestic 21 Moderate/Light 1,5 0,1 22 General/Medium 2,0 0,1 22+ General 2,0 0,1 23 Heavy 2,0 0,25 Commercial 31 Moderate 2,0 0,25 32 General 2,5 0,5 33 Heavy 3,0 0,5 34 Very heavy 3,0 0,5 Light industrial 41 Moderate 3,00,542 General 3,0 Not available 43 H
34、eavy 3,0 Not available Test method ISO 24346 ISO 24340 BS EN ISO 10595:2012 EN ISO 10595:2012 (E) ISO 201 56 Marking Floor coverings covered by this International Standard and/or their packaging shall bear the following marking: a) number and date of this International Standard, i.e. ISO 10595:2010;
35、 b) manufacturers or suppliers identification; c) product name; d) colour/pattern and batch number; e) classes/symbols appropriate for the product; f) the dimensions of a tile and the area, in square metres, contained in the package. 2BS EN ISO 10595:2012 EN ISO 10595:2012 (E)6 ISO 2012Annex A (info
36、rmative) Optional properties Where the following properties are required for specific applications, the floor covering should be tested in accordance with the appropriate methods: electrical resistance (ASTM F150, EN 1081, ANSI/ESD S7.1, ANSI/ESD STM 97.1); electrical propensity (EN 1815, ANSI/ESD S
37、TM 97.2 ); effects of stains (ASTM F925, EN 423, ISO 26987:2008); reaction to fire; determination of the burning behaviour using a radiant heat source (ISO 9239-1:2010, ASTM E648); reaction to fire; ignitability when subject to direct impingement of flame (ISO 11925-2:2010); reaction to fire, specif
38、ic optical density of smoke generated (ASTM E662); resistance to heat (ASTM F1514); resistance to light (ASTM F1515, ISO 105-BO2:1994, Method 3). BS EN ISO 10595:2012 EN ISO 10595:2012 (E) ISO 201 7Bibliography 1 ISO 9239-1:2010, Reaction to fire tests for floorings Part 1: Determination of the burn
39、ing behaviour using a radiant heat source 2 ISO 11925-2:2010, Reaction to fire tests Ignitability of products subjected to direct impingement of flame Part 2: Single-flame source test 3 ISO 105-BO2:1994, Textiles Tests for colour fastness Part B02: Colour fastness to artificial light: Xenon arc fadi
40、ng lamp test (including Amendment 1:1998) 4 ISO 26987:2008, Resilient floor coverings Determination of staining and resistance to chemicals 5 ANSI/ESD S7.1, Resistive Characterization of Materials Floor Materials 6 ANSI/ESD STM 97.1, Floor Materials and Footwear Resistance Measurement in Combination
41、 with a Person 7 ANSI/ESD STM 97.2, Floor Materials and Footwear Voltage Measurement in Combination with a Person 8 ASTM F150, Standard Test Method for Electrical Resistance of Conductive and Static Dissipative Resilient Flooring 9 ASTM F925, Standard Test Method for Resistance to Chemicals of Resil
42、ient Flooring 10 ASTM E648, Standard Test Method for Critical Radiant Flux of Floor-Covering Systems Using a Radiant Heat Energy Source 11 ASTM E662, Standard Test Method for Specific Optical Density of Smoke Generated by Solid Materials 12 ASTM F1066, Standard Specification for Vinyl Composition Fl
43、oor Tile 13 ASTM F1514, Standard Test Method for Measuring Heat Stability of Resilient Flooring by Color Change 14 ASTM F1515, Standard Test Method for Measuring Light Stability of Resilient Flooring by Color Change 15 ASTM F1914, Standard Test Methods for Short-Term Indentation and Residual Indenta
44、tion of Resilient Floor Covering 16 EN 423, Resilient floor coverings Determination of the effect of stains 17 EN 654, Resilient floor coverings Semi-flexible polyvinyl chloride tiles Specification 18 EN 1081, Resilient floor coverings Determination of the electrical resistance 19 EN 1815, Resilient
45、 and textile floor coverings Assessment of static electrical propensity 20 JIS A 1454, Test Methods Resilient Floorcoverings 21 JIS A 5705, Floorcovering PVC 2BS EN ISO 10595:2012 EN ISO 10595:2012 (E)This page deliberately left blankThis page deliberately left blankBSI is the independent national b
46、ody responsible for preparing British Standards and other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. BSI is incorporated by Royal Charter. British Standards and other standardisation products are published
47、by BSI Standards Limited.British Standards Institution (BSI)raising standards worldwideBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards and PASs are periodically updated by amendment or revision. Users of British Standards and PASs should make sure that
48、they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using British Standards would inform the Secretary of the technical committee responsible, the ide
49、ntity of which can be found on the inside frontcover. Similary for PASs, please notify BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers BSI Subscribing Members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of British Standards and PASs.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001E
