1、 ETSI TS 1Universal Mobile TelPhysical (3GPP TS 25.2TECHNICAL SPECIFICATION125 214 V13.2.0 (2016elecommunications System (al layer procedures (FDD) .214 version 13.2.0 Release 1316-04) (UMTS); 13) ETSI ETSI TS 125 214 V13.2.0 (2016-04)13GPP TS 25.214 version 13.2.0 Release 13Reference RTS/TSGR-01252
2、14vd20 Keywords UMTS ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can b
3、e downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
4、existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be
5、 subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: https:/portal.etsi.org/People
6、/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the wri
7、tten authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2016. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPP
8、TM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI TS 125 214 V13.2.0 (2016-04)23GPP TS 25.214 version 13.2.0 Release 13Intellectual Property
9、 Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essen
10、tial, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried o
11、ut by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI 3rd Generatio
12、n Partnership Project (3GPP). The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or GSM identities. These should be interpreted as being references to the corresponding ETSI deliverables. The cross reference between GSM, UMTS, 3GPP and
13、ETSI identities can be found under http:/webapp.etsi.org/key/queryform.asp. Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Ru
14、les (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI TS 125 214 V13.2.0 (2016-04)33GPP TS 25.214 version 13.2.0 Release 13Contents Intellectual Property Rights 2g3Foreword . 2g3Modal verbs termi
15、nology 2g3Foreword . 7g31 Scope 8g32 References 8g33 Definitions and abbreviations . 8g33.1 Definitions 8g33.2 Abbreviations . 10g34 Synchronization procedures . 11g34.1 Cell search 11g34.2 Common physical channel synchronization . 11g34.2.1 P-CCPCH radio frame timing . 11g34.2.2 S-CCPCH soft combin
16、ing timing . 11g34.2.3 Radio frame timing on the MBSFN layer . 12g34.2.4 Secondary serving HS-DSCH cell timing . 12g34.2.5 HS-DSCH cell timing when Multiflow is configured . 12g34.3 DPCCH/DPDCH/F-DPCH synchronization 12g34.3.1 Synchronization primitives . 12g34.3.1.1 General 12g34.3.1.2 Downlink syn
17、chronization primitives . 12g34.3.1.3 Uplink synchronization primitives 14g34.3.2 Radio link establishment and physical layer reconfiguration for dedicated channels . 14g34.3.2.1 General 14g34.3.2.2 Node B radio link set state machine 15g34.3.2.3 Synchronization procedure A 15g34.3.2.3A Synchronizat
18、ion procedure AA . 16g34.3.2.4 Synchronization procedure B 17g34.3.3 Radio link monitoring . 17g34.3.3.1 Downlink radio link failure . 17g34.3.3.2 Uplink radio link failure/restore in CELL_DCH state 18g34.3.3.2A Uplink radio link failure/restore in CELL_FACH state and IDLE mode . 18g34.3.4 Transmiss
19、ion timing adjustments . 18g35 Power control . 19g35.1 Uplink power control 19g35.1.1 PRACH . 19g35.1.1.1 General 19g35.1.1.2 Setting of PRACH control and data part power difference . 19g35.1.2 DPCCH/DPDCH/DPCCH2 19g35.1.2.1 General 19g35.1.2.2 Ordinary transmit power control . 20g35.1.2.2.1 General
20、 20g35.1.2.2.2 Algorithm 1 for processing TPC commands . 22g35.1.2.2.3 Algorithm 2 for processing TPC commands . 23g35.1.2.2.4 Algorithm 3 for processing TPC commands . 24g35.1.2.2A Ordinary transmit power control for DPCCH2 . 25g35.1.2.3 Transmit power control in compressed mode . 26g35.1.2.3A Tran
21、smit power control in compressed mode for DPCCH2 28g35.1.2.4 Transmit power control in the uplink DPCCH power control preamble . 29g35.1.2.5 Setting of the uplink DPCCH/DPDCH relative powers 29g35.1.2.5.1 General 29g35.1.2.5.2 Signalled gain factors 30g3ETSI ETSI TS 125 214 V13.2.0 (2016-04)43GPP TS
22、 25.214 version 13.2.0 Release 135.1.2.5.3 Computed gain factors . 30g35.1.2.5.4 Setting of the uplink DPCCH/DPDCH relative powers in compressed mode . 30g35.1.2.5A Setting of the uplink HS-DPCCH power relative to DPCCH or DPCCH2 power 31g35.1.2.5B Setting of the uplink E-DPCCH and E-DPDCH powers re
23、lative to DPCCH power. 34g35.1.2.5B.1 E-DPCCH/DPCCH when one transport block is transmitted on E-DCH 34g35.1.2.5B.1A E-DPCCH/DPCCH when two transport blocks are transmitted on E-DCH (rank-2) 36g35.1.2.5B.2 E-DPDCH/DPCCH . 36g35.1.2.5C Setting of the uplink DPCCH gain factor when no DPDCH is configur
24、ed . 40g35.1.2.5D Setting of the uplink S-DPCCH power relative to DPCCH power . 40g35.1.2.5D.1 Setting of the uplink S-DPCCH/DPCCH power ratio when less than two transport blocks are transmitted on E-DCH . 40g35.1.2.5D.2 Setting of the uplink S-DPCCH/DPCCH power ratio when two transport blocks are t
25、ransmitted on E-DCH (rank-2) . 41g35.1.2.5E Setting of the uplink S-E-DPCCH power relative to DPCCH power . 42g35.1.2.5F Setting of the uplink S-E-DPDCH power relative to E-DPDCH power . 42g35.1.2.6 Maximum and minimum power limits 42g35.1.3 Void 45g35.2 Downlink power control . 45g35.2.1 DPCCH/DPDC
26、H/F-DPCH . 45g35.2.1.1 General 45g35.2.1.2 Ordinary transmit power control . 45g35.2.1.2.1 UE behaviour . 45g35.2.1.2.2 UTRAN behaviour 46g35.2.1.3 Power control in compressed mode 47g35.2.1.4 Power scaling of DPDCH with POSRB49g35.2.2 Void 49g35.2.3 Void 49g35.2.4 AICH 49g35.2.5 PICH . 49g35.2.6 S-
27、CCPCH 50g35.2.7 Void 50g35.2.8 Void 50g35.2.9 Void 50g35.2.10 HS-SCCH . 50g35.2.11 HS-PDSCH . 50g35.2.12 E-AGCH . 50g35.2.13 E-HICH . 50g35.2.14 E-RGCH . 50g35.2.15 MICH 50g35.2.16 S-CPICH . 51g35.2.17 F-TPICH . 51g35.2.18 D-CPICH 51g35.2.19 E-ROCH . 51g36 Random access procedure 51g36.1 Physical ra
28、ndom access procedure . 51g36.1.1 RACH sub-channels . 53g36.1.2 RACH access slot sets 53g36.1A Physical random access procedure for Enhanced Uplink in CELL_FACH state and IDLE mode . 53g36.2 Void 55g36A HS-DSCH-related procedures 55g36A.1 General procedure 55g36A.1.1 UE procedure for receiving HS-DS
29、CH and HS-SCCH in the CELL_DCH state . 58g36A.1.1A UE procedure for receiving HS-DSCH and HS-SCCH in CELL_FACH state 62g36A.1.1B UE procedure for receiving HS-DSCH and HS-SCCH in the URA_PCH and CELL_PCH states 63g36A.1.2 UE procedure for reporting channel quality indication (CQI) and precoding cont
30、rol indication (PCI) 64g36A.1.2.1 CQI reporting procedure in case the UE is not configured in MIMO mode and not configured in MIMO mode with four transmit antennas in any cell . 64g36A.1.2.2 Composite PCI/CQI reporting procedure in case the UE is configured in MIMO mode 66g36A.1.2.3 Composite NTBP/P
31、CI/CQI reporting procedure in case the UE is configured in MIMO mode with four transmit antennas . 69g3ETSI ETSI TS 125 214 V13.2.0 (2016-04)53GPP TS 25.214 version 13.2.0 Release 136A.1.3 Node B procedure for transmitting the HS-DSCH and HS-SCCH . 70g36A.1.3.1 Node B procedure for transmitting the
32、HS-DSCH and HS-SCCH in the CELL_DCH state 70g36A.1.3.2 Node B procedure for transmitting the HS-DSCH and HS-SCCH in the CELL_FACH state 71g36A.1.3.3 Node B procedure for transmitting the HS-DSCH and HS-SCCH in the URA_PCH or CELL_PCH state . 71g36A.2 Channel quality indicator (CQI) definition. 72g36
33、A.2.1 CQI definition when the UE is not configured in MIMO mode and not configured in MIMO mode with four transmit antennas . 72g36A.2.2 CQI definition when the UE is configured in MIMO mode . 73g36A.2.2A CQI definition when the UE is configured in MIMO mode with four transmit antennas . 74g36A.2.3
34、CQI tables . 75g36A.3 Operation during compressed mode on the associated DPCH or F-DPCH 86g36A.4 Precoding control indication (PCI) definition 86g36A.4.1 PCI definition when the UE is configured in MIMO mode 86g36A.4.2 PCI definition when the UE is configured in MIMO mode with four transmit antennas
35、 . 87g36B E-DCH related procedures . 88g36B.1 ACK/NACK detection . 88g36B.2 Relative grants detection 89g36B.2A Absolute Grant Detection when the UE is configured with Implicit Grant Handling 89g36B.3 E-DCH control timing 89g36B.3.0 UE procedure for switching the E-DCH TTI length due to an HS-SCCH o
36、rder 90g36B.3.1 10 ms E-DCH TTI 90g36B.3.2 2 ms E-DCH TTI 90g36B.4 Operation during compressed mode . 91g36B.4.1 Uplink compressed mode 91g36B.4.2 Downlink compressed mode . 91g36C Discontinuous transmission and reception procedures . 91g36C.0 Discontinuous transmission/reception of DCH 92g36C.0.1 D
37、L_DPCH_DYN_DRX and UL_DPCH_DYN_DTX . 92g36C.0.1.1 DL_DCH_FET_Config = 0 . 92g36C.0.1.2 DL_DCH_FET_Config = 1 . 93g36C.1 Uplink CQI transmission 93g36C.2 Discontinuous uplink DPCCH/DPCCH2 transmission operation 94g36C.2.1 Uplink DPCCH burst pattern 94g36C.2.2 Uplink DPCCH preamble and postamble . 96g
38、36C.2.2.1 Uplink DPCCH preamble and postamble for the DPCCH only transmission . 96g36C.2.2.2 Uplink DPCCH preamble and postamble for the E-DCH transmission 96g36C.2.2.3 Uplink DPCCH preamble and postamble for the HS-DPCCH transmission 96g36C.3 Discontinuous downlink reception . 97g36C.3.1 Discontinu
39、ous downlink reception when the UE is in Multiflow mode . 99g36C.4 HS-SCCH orders 100g36C.5 Operation during compressed mode . 100g37 Closed loop mode 1 transmit diversity . 101g37.1 General procedure 102g37.2 Determination of feedback information . 103g37.2.1 End of frame adjustment . 103g37.2.2 No
40、rmal initialisation . 104g37.2.3 Operation during compressed mode . 104g37.2.3.1 Downlink in compressed mode and uplink in normal mode . 104g37.2.3.2 Both downlink and uplink in compressed mode . 104g37.2.3.3 Uplink in compressed mode and downlink in normal mode . 105g37.2.4 Initialisation during co
41、mpressed mode . 105g37.2.4.1 Downlink in compressed mode . 105g37.2.4.2 Uplink in compressed mode 106g37.3 Void 106g38 Idle periods for IPDL location method . 106g38.1 General . 106g38.2 Parameters of IPDL 106g38.3 Calculation of idle period position . 107g3ETSI ETSI TS 125 214 V13.2.0 (2016-04)63GP
42、P TS 25.214 version 13.2.0 Release 139 MIMO operation of HS-DSCH 109g39.1 General procedure 111g310 Uplink Closed Loop Transmit Diversity operation 111g310.1 General procedure 111g310.2 Downlink TPI transmission and control timing 113g310.3 Combining TPI bits from multiple radio links . 114g310.4 Op
43、eration during discontinuous uplink DPCCH operation 114g310.5 Operation during compressed mode . 114g310.5.1 Uplink compressed mode 114g310.5.2 Downlink compressed mode . 114g310.6 HS-SCCH orders 114g311 Uplink MIMO 115g311.1 General procedure 117g311.2 Downlink TPI transmission and control timing 1
44、17g311.3 Combining TPI bits from radio links of the serving radio link set . 118g311.4 Operation during discontinuous uplink DPCCH operation 118g311.5 Operation during compressed mode . 118g311.6 HS-SCCH orders 118g311.7 Uplink power control 118g312 MIMO operation of HS-DSCH with four transmit anten
45、nas . 118g312.1 General procedure 120g312.2 Symbol level interleaving . 120g312.3 Retransmission Procedures . 121g312.4 Precoding weight restriction . 121g312.5 HS-SCCH Orders . 122g3Annex A (informative): (no title) . 123g3A.1 Antenna verification . 123g3A.2 Computation of feedback information for
46、closed loop mode 1 transmit diversity . 124g3Annex B (Informative): Power control . 125g3B.1 Downlink power control timing . 125g3B.2 Example of implementation in the UE . 130g3B.3 UL power control when losing UL synchronization 130g3Annex C (Informative): Cell search procedure 131g3Annex D (Informa
47、tive): F-TPICH Transmission . 132g3Annex E (informative): Change history . 133g3History 140g3ETSI ETSI TS 125 214 V13.2.0 (2016-04)73GPP TS 25.214 version 13.2.0 Release 13Foreword This Technical Specification (TS) has been produced by the 3rdGeneration Partnership Project (3GPP). The contents of th
48、e present document are subject to continuing work within the TSG and may change following formal TSG approval. Should the TSG modify the contents of this present document, it will be re-released by the TSG with an identifying change of release date and an increase in version number as follows: Versi
49、on x.y.z where: x the first digit: 1 presented to TSG for information; 2 presented to TSG for approval; 3 or greater indicates TSG approved document under change control. y the second digit is incremented for all changes of substance, i.e. technical enhancements, corrections, updates, etc. z the third digit is incremented when editorial only changes have been incorporated in the document. ETSI ETSI TS 125 214 V13.2.0 (2016-04)83GPP TS 25.214 version 13.2.0 Release 131 Scope The present document specifies and establishes the characteristics of the physicals layer procedures in
