JUS C A4 040-1986 Mechanical testing of metals Hardness test Vickers test (HV 0 2 to less than HV 5)《金属的机械试验 硬度试验 维氏硬度（维氏硬度为0 2－5）》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

BS 3HR 401-2011 Specification for nickel-chromium-titanium-aluminium heat-resisting alloy seamless tubes (Nickel base Cr 19 5 Ti 2 2 Al 1 4)《镍铬钛铝耐热合金无缝钢管规格(镍基Cr19 5-Ti2 2-Al1 4)》.pdf

BS 3HR 501-2011 Specification for nickel-chromium-cobalt-titanium- aluminium heat-resisting alloy cold drawn wire for springs and springs (Nickel base Cr 19 5 Co 18 0 Ti 2 5 Al 1 5.pdf

BS 3HR 502-2011 Specification for nickel-chromium-cobalt-titanium- aluminium heat-resisting alloy cold drawn and solution treated wire for springs and springs (Nickel base Cr 19 5 .pdf

BS 3HR 503-2011 Specification for nickel-chromium-cobalt-titanium- aluminium heat-resisting alloy wire for thread inserts (Nickel base Cr 19 5 Co 18 0 Ti 2 5 Al 1 5) (0 45 mm to 2 .pdf

BS 3HR 504-2011 Specification for nickel-chromium-titanium heat-resisting alloy bar and wire for rivets and rivets (Maximum diameter or minor sectional dimension 20 mm) (Nickel bas.pdf

BS 3J 12-1991 Specification for pressure-sensitive adhesive identification tape《压敏胶粘识别带规范》.pdf

BS 3L 122-1970 Specification for ingots and castings of magnesium-8% aluminium-zinc-manganese alloy (solution treated) (Al 8 Zn 0 5 Mn 0 3)《镁-铝(8)-锌(0 5)-锰(0 3)合金铸锭和铸件规范(固溶处理)》.pdf

BS 3L 63-1971 Specification for tube of aluminium-copper-mangesium-silicon-manganese alloy (solution treated and precipitation treated) (Cu 4 4 Mg 0 5 Si 0 7 Mn 0 8)《铝-铜-(4 4)-镁(0 .pdf

BS 3L 80-1985 Specification for sheet and strip of aluminium-21 4% magnesium alloy (temper designation-O)《铝-镁2 25%合金板材和带材规范(强度符号-0)》.pdf