JUS M B2 113-1978 Spring washersfor high stresses curved and crinkled《高压弹簧垫圈，弯曲及褶皱》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

EN 12573-1-2000 en Welded Static Non-Pressurized Thermoplastic Tanks - Part 1 General Principles《焊接固定无压力热塑性槽罐 第1部分 总则》.pdf

EN 12573-2-2000 en Welded Static Non-Pressurized Thermoplastic Tanks - Part 2 Calculation of Vertical Cylindrical Tanks《焊接固定无压力热塑性槽罐 第2部分 立式圆柱形槽罐的计算》.pdf

EN 12573-3-2000 en Welded Static Non-Pressurized Thermoplastic Tanks - Part 3 Design and Calculation for Single Skin Rectangular Tanks《焊接固定无压力热塑性槽罐 第3部分 单层矩形壁的槽罐的设计和计算》.pdf

EN 12573-4-2000 en Welded Static Non-Pressurized Thermoplastic Tanks - Part 4 Design and Calculation of Flanged Joints《焊接固定无压力热塑性槽罐 第4部分 法兰连接的设计和计算》.pdf

EN 12574-1-2006 2366 Stationary Waste Containers - Part 1 Containers with a Capacity up to 10 000 I with Flat or Dome Lid(s) for Trunnion Double Trunnion or Pocket Lifting Device -.pdf

EN 12574-1-2017 en Stationary waste containers - Part 1 Containers with a capacity up to 10 000 l with flat or dome lid(s) for trunnion double trunnion or pocket lifting device - D.pdf

EN 12574-2-2006 374 Stationary waste containers - Part 2 Performance requirements and test methods《固定的废物容器 第2部分 性能要求和试验方法》.pdf

EN 12574-2-2017 en Stationary waste containers - Part 2 Performance requirements and test methods《固定垃圾箱-第2部分 性能要求和试验方法》.pdf

EN 12574-3-2006 459 Stationary waste containers - Part 3 Safety and health requirements《固定的废弃物容器 第3部分 安全性和健康要求》.pdf