1、.PMIL-I-8574E12 AuRust 1982SUPESSEDINGMIL-I-8574D10 September 1974MILITABY SPECIP KATIONINN1BIT08S, CORSOSION, VOLATILE, uTILIZATION OFlhia apecificacion 10 approved for uaa by all Ocparcmentaand ANent SealableCreamtproof ed, Untcrproofcd,Watervoporproof, Flexible,Brmaf iclal comnte (recommendations
2、, addit ion, dclationa) and anypertinent data which may be of use in improvins this document should beaddreaaed co: Snsincering Specifications and Standards Department (Code93) , Naval Air Sttsineering Canter, Lakahurst, NJ 08733 by usins theeel f-addreased Standardization Oocunant Improvement Propo
3、ml (OD Form1426) appearing at the and of this docuncnt or by letter.NO DELIVERABLEDATAREQu18SD BY 211IS WCUHE mProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. .nIL-I-8574ESPECIFICATIONS (Concinud)MILITARY (Continued)HIL-P-3420 Packaging Natarials,T
4、reated, opaqueVolatile Corrosion Inhibitor,fli L-lk-22019 Barrier Mnteriala, Transparent, Plexible,Senlnblo, Volatile Corrosion Inhibitor Treatedf4iL-B-22020 Bags, Transparent, Flexible, Sealable, VolatileCorrosion Inhibitor, TreatedH1L-1-2211O Inhibitors, Grroslon, Volatile, CryacallineM1l.-B-fIoO2
5、8 Bags, Barrier, with Volatile Corrosion InhibitorTrentcd LincrnSTANDARDS)iILITASYMIL-STO-1O5 Samplio8 Procedures and Tablea forby AttributesHIL-sTo-129 Harking for Shipment and StorageInspection(copietI of spccificotlons, standards, drawings, and publicationsrequred by manufacturers in connection w
6、ith specific acquisition functionsshould bc obtained from the contrncring activity or as directed by thecontroct lug of ficer. )* 2. 1.2 Order of precedence. In the cvcnc of a conflictbccwecn the text of this specification and the references cited herein.the text of this specification shall take pre
7、cedence.3. REQU1REHENTS* 3.1 First article. Uhcn specified, a sc.n!plc shall besubjccccd to first article inspection (sac L.2. I and 6.2).3.2 Hater ials. The volatile corrosion lnhibitore (VCI)shall cunform to Specification MIL- P-3L20, HIL-B-22019, MIL- I-22 I1O, orHIL-B-40028, and shall bc selecte
8、d for the intended applications fromthe approved types, classes, and styles covered in the respecclve specificntlon.a71 3.2.1 Nandlina of material. The VC1S shall ba stored i“a cool dry ores. The packaged VCI mntcrial shall not be opened untilready for use. Ouring the use opcroclona, the matcrlnl sh
9、all be keptprote.-tcd from excessive heat , direct sunllght , moisture, strong draftsand .?XCCSSIVC dusr. In continuous prcsorvation operations, theVC1-created matcrinl shall bc kept in a closed, eolf-st!aling concitincr.2.- . . . . . . . .Provided by IHSNot for ResaleNo reproduction or networking p
10、ermitted without license from IHS-,-,-t12L-I-8574EIf the self-sealing container i not nvolloble, the VCI-treated materialehcll be repleced in the origintrl container oc the end of each workingday and the container drall be closed. If this is impractical, the VCItreated m.ctarial shall be wrapped wit
11、h n barrier cerial conforming toqc-A-1876, HIL-B-121 Crada A, ML-B-131, or PPP-B-1055 Clan. C-. andthe wrap eccurcd in place. Where pachson of VC1 mnteriale are openedand non-operational poriode of indetorminace length occur then thematerial shall be repleced within its original container or in anot
12、hercontainer affording comparable protection, the concainer sealed, andplaced in a cool dry area. If the material has been aubjccted to ndamaging or adveree condlcion, the effeccivenean of the mccerial can bere-verified by conducting the vapor inhibitor ability (VIA) test of thematerial specificatio
13、n under which it wa8 originally produced.3.2. 1.1 Lined bnrriar baga. Punctured or otherwise dnmcgedbags shall be discarded.3.2.1.2 Bore. cubes. VC1-created tubee for insertion intobOXeB or cavltiee hall be kept in n closed container. The containershall be opened only for withdrawal of tubes for imm
14、ediate USI.?.3.2.1.3 Environmental effectm.a71 . Tcmperoture.(1) VCI ehould not be applied .to metal itenawhoac surface ccmporocure is greater then 150%, or where tha storeditem my be occasionally exptrscd co temperature of such mcgnlcude.(2) Ac low tempt! raturoe, VC1 IMY noc be effective;howt!verd
15、 little ctrrroaion will norrutlly occur at these c.anperacurea (leasthan 60 P) men without a prctaervative, .VO that VC1 mcy be used whereoccanioonl exposure co such temperature leveln le encountered.(3) In long term storage in warm arertn, (i. e.,tropical clime.tee) packcgca nhorrld be well sealed
16、to retard the 10.s6 ofvCI throu8h evaporation and migration from the pacluge.a71 b. Humidity.VCI pocka8e incariore should not be allowed toreaoin ac n high humidity level (Sretrtcr thnn 85-901 RH) for prolon6edperiode of time.c. Light .VCI paper or chemicnln should be used insidelightprrrof paekagaa
17、 for long term etorago applications.d. Air flow.VC1 packages should be protected from winds anddrnfte. If exposure is exceaalve and continuous airflow around chcpackqe ie unavoidable, the pnckage ehould be well eenled.3Provided by IHSNot for ResaleNo reproduction or networking permitted without lice
18、nse from IHS-,-,-. .HIL-I-8574E0.tiny solvents containingco ho vC1 protected.Acids or their vnporn.(1) Hydrochloric acid type metal cleaners andeulfidea should not bc ueed for cleaning of items(2) VCI protected items should not be exposedto industrial fumee contninins hydrogen chloride, hydrogen sul
19、fide,:, lfur diOxide or ther acidic v.spora.3.3 Limitation on us Unleee otharvise specified,:* CLs shall not bc uacd CO protact asswsblioo containing optical syetene“r Precision QWitV3 Parts which have elready been coated with a preservativeor I“brlcanc. Bonded films shall not be included in this ca
20、tegory (eeephnte or zinc phoephaco, with or without supplementary treatment. .,! t cases, direct contact of the VCI with non- ferroue mecala except.w. inure and aluminum-base alloys shall be avoided unle.sn specific:jmjssjon i.g ranted by the acquiring activity.3.2 Caution with PhtBti C, painted, or
21、 rubber parta. .+?mbl ICS containing plaetlc, painted, or rubber components or varnished!.:cquered ports ehall not be packaged with VCI until aftar cha. ., I r.ctor has furniehed proof to the acquiring activity that the.n.:i flc tnhlbicor and specific component hnve pnesed the compatibility, . . Tpc
22、cified in 4.3.1.1. 3.3 Restriction on use of different inhibitors in single pack.ml,lnbc ;ons of qualiflcd VC1 products may bo ueed in cho eamo pack,-, WJ.dWJ prior proof of coopacibilicy has been furnished to the acquiring.: iviy.3.b Cleaning and dryina. Wtcn bare metal parts are to be,., ,! p,. tc
23、.d with VC1, no residues foreign to the item shall remain afterlc:, ning. When a vapor dcgrcaser in uned, prccnutiona ehall be taken tonlctin the cleaning eolvent within tha prescribed clean linane and:.:miWCEt UrC llLUICE co prevent corrosion due to presence of w*ter orl:zwnposicion of solvent with
24、 subecquenc corrosion or release of toxic“ .P, r, . A1l other precautions ae furniahcd by the manufacturer of the, rt. ic:#Jar equipment shall be strictly ob.served.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ML- T.-8514F.3.5 Use of VCI with oper
25、ational lubricants. !4hereVCIsare to be applied to assemblies containing, operational lubricants, thecontractor shall furnish proof to the contracting activity that suchlubricants in conjunction with the specific VCI have satisfactorilypassed the compatibility test of 4.3.1. Prior to application of
26、VCI tothe assemblies, the excess oil shall be drained off (not applicable tobonded films) (see 6.4) .3.6 Application of VCI material.3.6.1 General.VCI-treated packaging material (SpecificationMIL-P-3420, MIL-B-22; ;9 MIL-B-22020, and MIL-B-40028) . Unless otherwisespecified, the VCI-treated material
27、s shall be applied so as to completelyenclose the item, or the part shall be wrapped with strips of the materialwithout any other material between the part and the wrapping. Completewrapping, where feasible, is preferred. The VCI-treated side of thepackaging mat2rials shall face the part being wrapp
28、ed, and shall beapplied so that any air entering the package shall pass through or overthe surface of the VCI before reaching cbe part. Surfaces to be protectedshall be not more than 12 inches from the VCI-treated materials. Allenclosures shall be sealed since the degree of protection afforded byche
29、 VCI vapors is directly proportional to the gas tightness of theenclosure, When VCI material is used as an overwrap, the amount of airwithin the wrap shall be kept to a minimum.b. vCI crystals (Specification MIL-I-2211O) . ThisVCI shall be spayed, atomized or dusted over the entire surface of :heite
30、m. Whenever feasible, che VCI shall also be sprayed, dusted oratomized into the enclosing container after which the container shallimmediately be sealed.3.6.2 Material in tiers or layers. When items are packedin tiers or layers , VCI shall be placed between the Ciers. Where theVCI-treated materials
31、are used in a carton comtaintng separators, allfaces of the separators shall be lined with the VCI-treated material inaddition to lining the inside of the carton.3.6.3 Cushioning and dunnage, Projections or sharp cornersand edges shall be adequately c,:shioned with moldable barrier materialsto preve
32、nt damage to either the part or the package. W%ere dunnage isrequired next to or around the item, a facing of VCI-treated barriermaterial shall be placed between the item and dunnage. In those unavoidablecases where the dunnage or other non-metallic materials used in thepackage may be hydroscopic or
33、 may give off corrosive vapors, the item andthe VCI shall be isolated from this by use of aluminum foil or othersuitable barrier materials. This is not necessary when such a barriermaterial is an integral part of the VCi-treated packaging material.5Provided by IHSNot for ResaleNo reproduction or net
34、working permitted without license from IHS-,-,-MIL-I-8574E3.6.4 Quantity required.a. VCI-treated packaging materials (SpecificationMIL-P-3420 and MIL-B-22019) . When used as a complete over-wrap, theminf.mum amount of the treated area of VCI-treated packaging materialsshall be at least equal to 3/8
35、of surface area of the enclosing container.Otherwise, the amount of the VCI-treated material shall be at leastequal co the surface area of the enclosing container.b. VCI crystals (Specification MIL-I-2211O) .tlmount of VCI shall be 1 gram of VCI per.cubic foot of volume of theenclosing container.3.6
36、.5 Closed and blind-end components. Enclosed portionsof assemblies, such as gear boxes, shall have VCI applied inside cheenclosed space, and the enclosed volume shall be sealed. Open-end voidswhere the opening is small with relation co the void, shall be treatedas specified above for enclosed portio
37、ns of an assembly. Open-end voidsof a depth greater than 6 inches shall have VCI inserted in the void.The minimum quantity of VCI required for protection of the enclosedspaces of closed and blind-end components shall be determined as specifiedin 3.6.4. Whenever an enclosed assembly is preserved with
38、 a VCI andsealed, an appropriate warning in the form of a label or a tag shall beapplied rO aSSUre chat che assembly will nOt be used prior co the applicationof the proper lubricant after removal of the VC1, if necessary.3.6.6 Greaseproof barrier. Parts covered with operationaloil films shall have a
39、 greaseproof barrier bet,deen the VCI and the outerpackaging materials to prevent the latter from becoming oil soaked.Whenever possible, VCI-treated material conforming to Styles C and G ofSpecification MIL-P-3420, shall be used for this purpose since thebarrier is an integral part of these VCI-trea
40、ted materials.3.7 Unit protection. Proper performance and preservativequalities of VCI are dependent upon the following:a. Its use in a confined area where the circulationof air is limited.* b. The application of the VCI being in accordancewith the requirements of 3.6.1.The degree of protection requ
41、ired for an item, when VC1 is used, shallbe governed by the nature (critical and noncritical) and composition ofthe item.* 3.8 Marking. Unit and intermediate packages and shippingcontainers shall be marked in accordance with MIL-STD-129.3.9 Depreservacion. Crystalline or powdery depositsobserved on
42、the surfaces of critical moving parts uay be removed byrinsing or scrubbing with methanol prior to the application of theoperational lubricant.6Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-I-8574E4. QUALITY ASSURANCE PROVISIONS4.1 Responsibili
43、ty for inspection. Unless otherwisespecified in the contract or purchase order, the contractor is responsiblef& the performance of all inspection requirements as specified herein.Except as otherwise specified in che contract or purchase order, thecontractor may use his own or any ocher facilities su
44、itable for theperformance of the inspection requirements specified herein, unlessdisapproved by the Government. The Government reserves the right toperform any of the inspections set forth in the specification where suchinspections are deemed necessary to assure supplies and services conformto presc
45、ribed requirements.* 4.2 Classification of inspections. The inspectionrequirements specified herein are classified as follows:a. First article inspection (see 4.2.1).b. Quality conformance inspection (see 4.2.2).4.2.1 First article inspection. The first article inspectionshall consist of examination
46、 and tests for all of the requirements ofthis specification. The inspection shall be performed by the firstarticle inspection laboratory designated by the contracting officer (see6.2). When specified, first article inspection shall be conducted bythe contractor in the presence of a Government repres
47、entative designatedby the contracting officer. Approval of the first article inspectionsample does not preclude the requirements for performing the qualityconformance inspection. First article inspection may be waived when theacquiring activity or contract administration activity has data or otherev
48、idence to indicate that prior successful first article Impection hasbeen conducted.4.2.1.1 First article samples. When specified by the contractingofficer (see 6.2) the contractor shall submit a first article samule ofsufficient material to conduct all tests required by this specification.The sample
49、 shall be produced by the contractor or furnished by a supplierand manufactured using the sane production processes, procedures andequipment used in fulfilling the contract. Prior to submission thecontractor shall inspect the sample to assure that it conforms to therequirenencs of the contract and shall submit a record of this inspection.A first article sample shall be submitted, as directed by the contractingofficer, whenever a c
