1、MIL-R-85535 (2) 5 m 7777706 0175556 5 m F.-sq-c3 MIL-R-85535(AS) AMENDMENT 2 26 August 1986 SUPERSEDING AMENDMENT 1 14 DEC 1983 MILITARY SPECIFICATION RECORDER-REPRODUCER SET, DIGITAL DATA, ANIASH-33 This amendment forms a part of Military Specification MIL-R- 85535(AS) dated 8 June 1983, and is app
2、roved for use by the Naval Air Systems Command, Department of the Navy and is available for use by all Departments and Agencies of the Department of Defense. PAGE 1 1 .l, line 15: Delete “AN/AYK-l14(V)“ and substitute: “AN/AYK-l4(V) .It PAGE 3 2.1.1, After MIL-R-5757 add: ttMIL-E-6051 Electromagneti
3、c Compatibility Requirements Systems“ -_I_ C? The attached insertable replacement pages listed below are replacements for stipulated pages. insert the amendment as the cover sheet to the specification. L When the new pages have been entered in the document, Replacement Page 47 48 49 50 62A 6220, Del
4、ete in its entirety and substitute: “3.3.20 Safety. accordance with the applicable requirements of MIL-STD-882 (See 6.2.2). Primary emphasis of the safety program should be on the hazards associated with the interrelationships between the operating and maintenance personnel, the air vehicle, the var
5、ious avionics devices, and the avionics system designed to integrate this equipment into the air vehicle. For example: The system shall be analyzed to determine if unplanned or inadvertent commands are generated, critical controls shall be designed and located to preclude inadvertent operation, comp
6、uter programs shall include logic to prevent the system from entering into unsafe or dangerous mode of operation. and its components shall be designed and the CFE developed for safety in accordance with MIL-E-5400. The contractor shall conduct a system safety program in The system 3.3.20.1 X-Radiati
7、on exposure. X-radiation producing equipment shall be designed to limit the personnel dosage rate at any readily accessible point, measured two inches from the outer surface, to a 0.5 millirem per hour with external shielding removed or 500 millirem per year (BIMED NAVMED P5055). This requirement ap
8、plies to the areas normally inhabited by personnel during installation, calibration, maintenance, and operation of equipment. 3.3.20.2 Electromagnetic radiation exposure. The system design criteria shall include provisions for protection of personnel from RF electromagnetic, electrostatic and shock
9、hazzards in accordance with requirement 1 of MIL-STD- 454. Where possible, protection provisions shall be designed into associated adequate safety precautions shall be provided. subsystem/equipments. When protection by design is not technically feasible, - 4 Provided by IHSNot for ResaleNo reproduct
10、ion or networking permitted without license from IHS-,-,-c MIL-R-85535 (2) 58 = 7777906 OL755b0 7 M MIL-R- a5 53 5 Amendment 2 3.3.20.3 Toxicity. Personnel exposure to toxic air contaminants during system operation or maintenance shall be evaluated and minimized. additior, any malfunction of the ele
11、ctrical power and distribution system, avionics or other electrical system component in the form of but not limited to electrical fires and battery chemical releases shall not release into the cockpit or cabin area any gases, fumes, vapors or particulates which could incapacitate the crew and subseq
12、uently result in inability to successfully perform an emergency landing or ditching and egress. vapors and particulates shall be positively prevented from leaking back into the cockpit or cabin area from when they are purged. In These gases, fumes, 3.3.20.4 Electronic equipment hazards. All newly de
13、signed electronic equipments and modified portions of existing electronic equipment shall be in accordance with MIL-STD-454 requirement 1.“ PAGE 40 3.4.1.3.1, last line: Delete: n3.5.2.2.2.t1 and substitute: n3.5.1.3.2.1.R 3.4.1.3.2, last line: Delete: “3.5.1.3.2.1.“ and substitute: n3.5.1.3.2.2.tt
14、3.4.1.3.3, last line: Delete: tt3.5.1.3.2.2.n and substitute: “3.5.1.3.2.3.“ PAGE 42 3.4.4, last line:, Delete: c -3 %- “SECNAVINST 3560.1 and MIL-STD-1679II and substitute: “DoD-STD-21 67“ PAGE 43 TABLE V, Description column, line 17: Delete: “Figures 10A, 10B, and 11“ and substitute: “Figures 10,
15、11, and 12.tt PAGE 46 3.5.1.1. Add: “h. Control each tape units tape motion, in DMTU Auto Mode.“ PAGE 48 Figure 10: Delete and substitute attached FIGURE 10. PAGE 49 Figure 11: Delete and substitute attached FIGURE 11. PAGE 50 Figure 12: Delete and substitute attached FIGURE 12. 5 Provided by IHSNot
16、 for ResaleNo reproduction or networking permitted without license from IHS-,-,-Y MIL-R-85535 Amendment 2 PAGE 52 TABLE IV, Type Device column, lines 18 through 23: Delete: “Mon“ and substitute “Alt.“ PAGE 54 3.5.1.3.2.2, line 11: Delete: n3.5.2.2.3w and substitute “AD 1404.“ 3.5.1.3.2.2, line 13: D
17、elete: “3.5.2.2.3.3.1“ and substitute “AD 1404.“ 3.5.1.3.2.2.1, line 6: Delete: “Xn and substitute nX-l.n PAGE 55 TABLE VI, Add vertical line between “Exception“ and llDisplayw Columns. TABLE VII, Exception column, line 6: Delete: “Out“ and substitute “Out (TO).“ TABLE VII, Normal column, line 15: D
18、elete: IDC“ and substitute “DW.“ PAGE 56 TABLE VII, NOTES: After liCIW“ add “CRS = Channel Reset SC = System Controller TO = Times Out“ TABLE VII, NOTES, lines 11 and 12: Delete: “The IDS“ and substitute “AD 1404.“ PAGE 57 TABLE VIII, Title: Delete: “ASP“ and substitute “SASP.“ TABLE VIII, Exception
19、 column, line 6: Delete: “Out“ and substitute “Out (TO).“ PAGE 58 TABLE VIII, Title: Delete: “ASP“ and substitute “SASP.“ TABLE VIII, Notes: After “DU“ add “CRS = Channel Reset SC = System Controller TO = Times Out“ TABLE VIII, NOTES, lines 10 and 11: Delete: “The IDS: and substitute “AD 1404.“ 3 .-
20、 PAGE 59 TABLE X, Exception column, line 6: Delete: “Out“ and substitute “Out (TO).“ 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-R-5535 (2) 5B 9999906 0375562 O I MIL-R-85535 Amendment 2 PAGE 60 TABLE IX, Notes: After “IPL“ add “CRS = Chann
21、el Reset SC = System Controller“ TABLE IX, NOTES, line 7: Delete: “Time Out“ and substitute “Times Out.“ TABLE IX, NOTES, lines 13 and 14: Delete: “The IDS1 and substitute “AD 1404.“ PAGE 61 TABLE X, Exception column, line 6: Delete: “Out“ and substitute “Out (TO).“ PAGE 62 TABLE X, NOTES: After “IP
22、Ln add “CRS = Channel Reset SC = System Controller“ TABLE X, line 8: Delete: “Time Out“ and substitute “Times Out.“ TABLE X, NOTES, lines 13 and 14: Delete: “The IDS“ and substitute “AD 1404.“ t-3 3.5.1.3.2.2.1, line 5: Delete: “four“ and substitute “five.“ -=A. 3.5.1.3.2.2.1, line 9: Delete: I1Xw a
23、nd substitute “X-1.“ Add Table X-1 as page 62A. Add Table X-1 (Continued) as page 62B. PAGE 63 3.5.1.3.2.2.1: Add: “e. System Loader - Table X-1.“ 3.5.1.3.2.2.1, last line: Delete: “and X“ and substitute “X and X-1,“ PAGE 64 3.5.1.3.2.2.1.5, after paragraph 3.5.1.3.2.2.1.5, and new paragraph 3.5.1.3
24、.2.2.1.6: “3.5.1.3.2.2.1.6 System Loader (SLDR) load option. hardware, initiating the system loader load option shall initiate the When implemented in the command sequence specified in Table X-l. DW sequences shown in the table shall cause the corresponding messages to be displayed to the operator.“
25、 Receipt of the CIW sequences and PAGE 03 Figure 18: Delete and substitute attached FIGURE 18. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-R-5535 (2) 58 m 9979906 0375563 2 m 1 MIL-R-85535 Amendment 2 PAGE 85 Figure 19: Delete and substitut
26、e attached FIGURE 19. PAGE 87 TABLE XI, Control or Indicator column, line 9: Delete: VND“ and substitute “LAMP. PAGE 89 3.5.3.1.3.1.2.3.2.f, line 1: Delete: “Reverse“ and substitute “Rewind.“ PAGE 92 3.5.3.1.3.2.5, line 2: Delete: “have no more than one permanent error per lo6 bits.“ free of permane
27、nt errors over the useable tape length.“ and substitute “be PAGE 94 TABLE XII, Requirement Paragraph column, line 3: Delete: “3.3.“ TABLE XII, Requirement Paragraph column, Line 8: Delete: “3.3.13.7“ and substitute: “3.3.13.“ TABLE XII, Requirement Paragraph column, line 19: Delete: “3.3.10“ and sub
28、stitute “3.3.10.4.“ TABLE XII, Requirement Paragraph column, last line: Delete: n3.4.3.5w and substitute “3.4.4, 3.5.“ PAGE 95 TABLE XIII, Requirement Paragraph column, line 3: Delete “3.3. 4.5.1.3, line 5: Delete: w+85C“ and substitute “+55C.“ PAGE 98 FIGURE 23: Delete and substitute attached FIGUR
29、E 23. PAGE 99 FIGURE 24: Delete and substitute attached FIGURE 24. PAGE 100 4.5.1.3.1: Delete subparagraphs b through h and Substitute: “b. High operating temperature: +55OC (with dummy cartridge) c. High operating temperature: +5OoC (with operational tape) J 8 Provided by IHSNot for ResaleNo reprod
30、uction or networking permitted without license from IHS-,-,-MIL-R-5535 (2) 58 W 777770b 01755611 11 MIL-R- 85 535 Amendment 2 d. Low operating temperature: -25OC (with dummy cartridge) e. Low operating temperature: f. Chamber temperature rate: OC (with operational tape) 5C per minute (minimum)n PAGE
31、 104 4.5.6.2, line 3: Delete: “Method gn and substitute Method 4.“ PAGE 105 4.5.2.5, line 3: Delete: “Method 9“ and substitute “Method 4.n PAGE 106 4.7, last line: Delete: “4.9.5“ and substitute “4.8,“ PAGE 111 6.2.2, Add new data requirements after 3.3.19: Paragraph Data Applicable No. - Requiremen
32、t Type DID No. - Opt ions -.I “3.3.20 System Safety Program Plan DI-SAFT-801 O0 - , System Safety Report“ DI-SAFT-80104 - PAGE 112 6.2.2, Delete all items under paragraph 3.4.4 and add: Paragraph Data Applicable - DID No. Options No . Requirement Type - - “31ri.4 merface Design Document DI-MCCR-8002
33、7 - Software Development Plan DI-MCCR-80030 - Data Base Design Document DI-MCCR-80028 - , ri - Software Requirements DI-MCCR-80025 - Specificationn 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-R-85535 Amendment 2 PAGE 113 6.2.2, Delete all i
34、tems under paragraph 4.5.7 and add: Paragraph Data - No. - Requirement Type 4.5.7 Computer Resources Integrated Support Document Software Quality Evaluation Plan Computer System Operators Manual Software Test Procedures Software Test Report Applicable DID No. D-MCCR-80024 DI-MCCR-80010 DI-MCCR-80018
35、 DI-MCCR-80016 DI-MCCR-80017 6.2.2, paragraph 4.9.2, line 2: Delete: “Assurance DI-R-2174“ and substitute “Evaluation DI-MCCR-80010“ Preparing activity (Project 5835-N 080) Navy-AS 10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MI L-R-8 5535 (AS)
36、 3.5.1.2.2.2 Initiate BIT/master clear (CLR) pushbuttons. Degression of either of tne CLR pusnouttons men in the Off L ine Hode shafl cause the Corresponding control section (1 or 2) to enter a predetermined initialized stbtt. BIT/Master Clear function shall be characterized by: It shall oe equivale
37、nt to the IYASTE CLEAR function. The Snit a. o. Initialzation of the assigned computer interface logic. Initialization of the assigned DMTU(s) to a stopped, ready condition. c. Termination of any pending operations, d. The clearing of the OP display. e. 8IT of the selected configurations. The Initia
38、te BIT/Master Clear pushbuttons shall be available .when Off Line Hode i; selected. 3.5. i .2.2.3 Overtemoerature Indicator operat ion. An Overtemperature (aVE!? TEMP) indicator shall be provided to warn the operator that the DMTC tenperature is 35OC or higher or a fan has failed. illuminate red to
39、indicate that the temperature of the DMTC has reached the warning level. signal pair avai 1 ab1 e at a connector for external overtemperature warning applications. transferring 500 milliamps current, either AC or DC, through the closed (overttrnperature activated) circuit. This relay closure is to b
40、e used in accordance nitn 3.3.13.1. Tne indicator shall In addition to the indicator, there shall be a relay closure Tne relay closure signal pair and relay shall be capable of T -5. 3.5.1.2.2.4 Time totalizing meter. A time totalizing meter of a type in accordance with 3.3.2.4 Shall be provided on
41、the DMTC to indicate accumulated on-tim for the DMTC. 3.5.1.2.2.5 LAMP TEST. Depression of a LAW TEST switch shall cause all indicator lamps to illuminate and shall cause the projection readout (?fio) switches to cycle through all legends (levels). Each PRO level shall be illuminated for a half-seco
42、nd before changing to the next level. The PRO levels shall cycle redundantly as long as the pushbutton is depressed. Refer to Figures 10, 11 and 12 for the various PRO levels. necessary display and control capaoiity to allow an operator to fully implement all features of DMTS operating modes and as
43、o minimum shall provide the following features. 3.5.1.2.2.6 Operator diSDlayS and controls. The OP shall have the 47 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-R-85535 (2) 58 = 7777906 0375567 T MIL-R-85535 Amendment 2 2 a c U c a c o QQ -I
44、z II w 5 Y W a 45“ I- U o J w w d w O n a 3 cn IQ c c 8 4 8 c U 48 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-R-8553.5 Amendment 2 i m W I i-Jr on L Y m ou o =I Q, li al C c - e cc O e- t El El . c c w a s I El ri. 49 Provided by IHSNot for
45、ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-R-85535 (2) 5 W 7799906 0375567 3 I- MIL-R-85535 Amendment 2 ON LINE MODES BASELINE LEV li j1ND.11 , , . , FIGURE 12. On line mode PRO displays 50 Provided by IHSNot for ResaleNo reproduction or networking permitted with
46、out license from IHS-,-,-MIL-R-85535 (2) 58 m 7797706 0375570 T = TABLE X-1. System loader load sequence Normal - Send SRL Control Frm Rewind lape Wait 1 Second Send IMPL Comnand CIY FOOQ0000 Receive Good IMPL Response CIW = E0000060 Receive Good IPL Response CIW = E0000020 Send SC LO Comnand CIW =
47、01040001 DU = 00045101 Receive Good TC Response CIU 01800000 MIL-R-85535 Amendment 2 Di splay SRL IWL , IMPL CMP IPL CMP S?dervol tage sensors shall provide p-?tection for the OMTU Dy monitoring the DC voltages and shutting down the 3C to DC converter if the sensed limits are exceeded. 3.5.3.1.3.1.2
48、.2 Servo s stem. The DMTU servo system shall initiate and regulate the movement 2 O o Do I- z I 5 U I w z O L 3 c a o O 00 I a 98 I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-R-85535 (2) 58 W 7777706 0175578 LI W MIL-R-85535 Amendment 2 r n U o yc VI O o 2 a3 O t O O0 O O O0 O O O0 oc 0: O0 O O O0 O F b w N 5i K 3 O I a 6 2 5 I c I O t I U w VI w (3 ,/. V O O 99 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-R-85535 (2) 58 m 7777706 0375577 b = MI L-R-8 5535
