1、.-,EEElMl LSTDl 651A3 APRIL 1992SUPERSEDINGMILSTD165127 JUNE 1975MILITARY STANDARDINSERT ARRANGEMENTS FOR MILC5015,MILC22992 (CMSSES C, J, AND R),AND MILC83723 (SERIES 11)ELECTRICAL CONNECTORSAMSC NO DELIVERABLE DATA REQUIRED BY THIS STANDARD. FSC 5935DISTRIBUTION STATEMENT A. Approved for public re
2、lease; distribution is unlimited.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-1651AFOREWORO1. This Military Standard is approved for use by all Departments andAgencies of the Department of Defense.2. Beneficial comments (recommendations, a
3、dditions, deletions) and anypertinent data which may be of use in improving this document should beaddressed to: Commanding Officer, Naval Air Harfare Center Aircraft DivisionLakehurst, Code SR3, Lakehurst, NJ 08733-5100, by using the StandardizationDocument Improvement Proposal (00 Form 1426) appea
4、ring at the end of thisdocument or by letter.IIL iiProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-II1-MIL-STD-1651ACONTENTSPARAGRAPH PAGE1.1.12.2.1;.;.12:3:14.5.5.15.25.3:16.26.36.46.56.66.711;APPENDIXABSCOPE Scope APPLICABLE DOCUMENTS .Government d
5、ocuments .Specifications, standards and handbooks Non-Government publications Order of precedence DEFINITIONS Definitions GENERAL REQUIREMENTS (NOT APPLICABLE ) OETAIL REQUIREMENTS Dimensions .Marking Contacts .NOTES Intended use .Oata requirements Issue of DODISS Supersession data International sta
6、ndardization agreements .Changes from previous issue Subject term (keyword) 1isting .11111222222:3555:1:10PAGEContact designation .4Insert arrangements cancelled by revision A to MIL-STO-1651 5Insert arrangements removed from MIL-STO-1651 by revision A 9MIL-C-5015, MIL-C-22992 and MIL-C-B3723 Series
7、 11 InsertArrangements . 11Insert Arrangements Cancelled by Revision A to MIL-STO-1651 215,0iii/ivProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-1651A1.1. SCOPE1.1 =. This standard gives the dimensional requirements for insertarrangements us
8、ed in MIL-C-5015, MIL-C-22992 (Classes C, J and R), andMIL-C-83723 (Series II) electrical connectors.2. APPLICABLE 00CUMENTS2.1 Government documents.2.1.1 Specifications, standards and handbooks. The following specifica-tions, standards and handbooks form a part of this document to the extent spec-i
9、fied herein. Unless otherwise specified, the issues of these documents are thoselisted in the issue of the Department of Defense Index of Specifications andStandards (0001SS) and supplement thereto, cited in the solicitation (see 6.3).SPECIFICATIONSMILITARYMIL-C-5015MIL-C-39029MIL-C-22992MIL-C-83723
10、Connectors, Electric, “AN” TypeContacts, Electrical Connector, General SpecificationforConnectors, Plugs and Receptacles, Electrical , Water-proof, Quick Disconnect, Heavy Duty Type, GeneralSpecification forConnectors, Electrical (Circular, EnvironmentResisting) , Receptacles and Plugs, General Spec
11、ifica-tion forSTANDAROSMILITARYMS3400 Connector, Receptacle Electric, Wall Mounting, FrontRelease, Crimp Contact, AN TypeMS3450 Connector, Receptacle Electric, Wall Mounting, RearRelease, Crimp Contact, AN TypeMS14056 Contact, Electric Connector, Shielded CableApplications, Size 8MS33695 Contact, Vi
12、deo Coaxial Connector(Unless otherwise indicated, copies of military specifications and standardsare available from the 000SSP, Standardization Oocuments Order Desk, 700Robbins Avenue, Building 4D, Philadelphia, PA 19111-50g4.)I1Provided by IHSNot for ResaleNo reproduction or networking permitted wi
13、thout license from IHS-,-,-MIL-STD-1651A2.2 Non-Government publications. The following documents form a part ofthe document to the extent speclfled herein. Unless otherwise specified, theissues of the documents which are DOD adopted are those listed in the issue ofthe DODISS cited in the solicitatio
14、n (see 6.3).AMERICAN NATIONAL STANOARDS INSTITUTE (ANSI)ANSI Y14.5M Dimensioning and Tolerancing (OOD Adopted)(Application for copies should be addressed to the American National StandardsInstitute, 1430 Broadway, New York, NY 10018-3308.)(Non-Government standards and other publications are normally
15、 available fromthe organizations that prepare or distribute the documents. These documentsalso may be available in or through 1ibraries or other informational services.)I 2.3 Order of precedence. In the event of a conflict between the text ofthis document and the references cited herein, the text of
16、 this document takesprecedence. Nothing in this document, however, supersedes applicable laws andregulations unless a specific exemption has been obtained.3. DEFINITIONSa713.1 Definitions. The terms used in this standard are generally acceptedby the electrical and electronics industries and commonly
17、 used in electricalconnector engineering practice. An illustration of some of the terms used is a71shown belOW:t OF MASTER KEY ORI KcYw4v OF SHELLd!MASTERKEYORKEYWAYOF SHELL A INDEXING RADIUS OF #“SEll,ENGAG!NG FACE OF PIN INSERT(SOCKET #NSERT OPPOSITE)4.Not5.GENERAL REQUIREMENTSapplicable.DETAIL RE
18、QUIREMENTS5.1 Dimensions. Dimensions shall be in accordance with the applicablesection of Appendix A of this standard and the following dimensional data:a. Dimensioning and tolerancing in accordance withNl;lle;14.5-1982. Dimensions are true position and are inI 2LProvided by IHSNot for ResaleNo repr
19、oduction or networking permitted without license from IHS-,-,-MIL-STD-1651AIIIIIab. Metric equivalents (to the nearest .D1 MM) are given forgeneral information only and are based upon 1 inch = 25.4 mm.c. Dimensions and markings shown are for engaging face of pininsert. Socket insert is opposite.d. T
20、he following tolerances apply to insert installed in shell:1. The center of each hole in insert for crimp contactconnectors shall be located at true position within .014dia.fill.014dia.2. The center of engaging end of each contact shallocated in true position within .024 dia. *e. Unless otherwise in
21、dicated, dimensions are symmetrical aboutcenterline.indicates CL of insert arrangement.f. Each insert arrangement is shown in the “normal position” inthe shel1.5.2 Marking. Marking shall be in accordance with MIL-C-5015,MIL-C-22992, or MIL-C-83723, as applicable, and as shown in the applicablesectio
22、n of this military standard.5.3 Contacts. Solder contacts shal1 be in accordance with MIL-C-5015,MIL-C-2299 or MIL-C-83723, as applicable. Crimp contacts shall be inaccordance with table 1. Contact sizes are designated by the symbols shown intable 1.Provided by IHSNot for ResaleNo reproduction or ne
23、tworking permitted without license from IHS-,-,-MIL-STD-1651ATABLE 1. Contact designation.Crimp or solder contacts Crimp contact part numbers ISizeo48121616SS (shielded)Video coaxSymbol03(De03MIL-C-5015 MIL-C-5015 and MIL-c-83723MS3400s Connectors Series II MS3450s ConnectorsMIL-C-39029 Contacts MIL
24、-C-39029 ContactsMIL-C-39029/44 I rt39029/29-o-o IMIL-C-39029/44 I M39029/29-8-8 IaMIL-C-3Y029/45 M39029/30-8-8MIL-C-39029/44 M39029/29-12-12MIL-C-39029/45 M39029/30-12-12MIL-C-39029/44 1439029/29-16-16MIL-C-39029/45 1!39029/30-16-16 a71NA I M39029/30-16S16 IMS14056 (MIL-C-5015 only)MS33695 (MIL-C-5
25、015 Oflly) Ia714Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-1651AIi-1IIII1II6. NOTES(This section contains information of a general or explanatory nature that maybe helpful, but is not mandatory.)6.1 Intended use. This standard contains r
26、equirements for insertarrangements to be used in MIL-C-5015, MIL-C-22992 (Classes C, J, R) andMIL-C-83723 (Series II) Electrical Connectors.6.2 Data requirements. No data is required by this standard.6.3 Issue of DOOISS. When this standard is used in acquisition, theapplicable issue of the DODISS mu
27、st be cited in the solicitation (see .?.1.1,2.2).* 6.4 Supersession data. Table II gives the insert arrangements whichhave been cancelled by Revision A to MIL-sTO-1651 . The insert patterns forthese insert arrangements are contained in Appendix B. Manufacturers maycontinue to supply connectors using
28、 these insert patterns until 30 April1994, or deplete their inventories, whichever comes first. Table 111 givesinsert arrangements and their previous status which have been deleted fromMIL-STD-1651 with the publication of Revision A.* TABLE II. Insert arrangements cancelled by Revision A to MIL-STD-
29、1651.InsertArrangement Status in MIL-STD-1651 Replacement12s, 13-1 Inactive for designatter 8 March 194512S, 13-2 Inactive for designafter 17 April 194514s, 15-10 Inactive for designafter B December 194514s, 15-11 Inactive for designafter 1? April 194514S, 15-12 Inactive for designafter 17 April 194
30、514s, 15-13 Inactive for designafter 17 April 194516S, 17-14 Inactive for designafter 27 April 194516S, 17-15 Inactive for design 16S, 17-4after 27 April 1945I 5LProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-sTD-1651A*TABLE 11. a71Insert arrang
31、ements cancelled by Revision A to MIL-STD-1651 - continued.InsertArrangement16S, 17-1616s. 17-1718-1718-lB18-1918-2318-2418-2518-2618-271B-2818-3018-3120-1020-2520-26Status in MIL-STO-1651 ReplacementInactive for design 16S, 17-4after 27 April 1945Inactive for design 16-14after 27 April 1945Inactive
32、 for design 18-9after 19 May 1945Inactive for design I 18-9after 19 May 1945Inactive for designafter 19 May 1945 IInactive for design 18-1after 19 May 1945Inactive for design lB-1after 19 May 1945Inactive for design 18-3after 19 May 1945Inactive for design 18-3after 19 Fiayi9451Inactive for design 1
33、8-5after 19 May 1945Inactive for design I 18-5after 19 May 1945Inactive for designI18-20after 19 May 1945Inactive for design I 18-20after 19 May 1945Inactive for designafter 1 June 1945 IInactive for design 20-11after 1 June 1945Inactive for designafter 26 June 19456a71Provided by IHSNot for ResaleN
34、o reproduction or networking permitted without license from IHS-,-,-IIIIMIL-sTD-1651AIIa71 *TABLE II. Insert arrangements cancelled by Revision A to MIL-STD-1651 - continued.InsertArrangement I Status in MIL-STD-1651 I ReplacementIIIIII20-30 I Inactive for designI20-11after 1 June 194520-32 I Inacti
35、ve for design I 20-7after 1 June 194522-30 I Inactive for design I22-14after 26 June 194522-32IInactive for design I 22-5after 26 June 194522-35IInactive for designafter 26 June 1945 I24-15 Inactive for design 24-5after 26 June 194524-18 Inactive for designafter 26 June 194524-24 I Inactive for desi
36、gn I 24-5after 26 June 194524-25 I Inactive for design I 24-6after 26 June 194524-26 Inactive for design 24-6after 26 June 194528-7 Inactive for designafter 13 May 195428-13IInactive for designI28-12after 26 June 194532-16IInactive for designI32-6after 26 June 194532-18IInactive for design I 32-4aft
37、er 26 June 194532-19 I Inactive for design I 32-1after 26 June 194532-20IInactive for designI32-6after 26 June i9457Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-*TABLE II. Insert arrangements cancelled by Revision A to MIL-STD-1651 - continued.Ins
38、ertArrangement Status in MIL-STD-1651 Replacement36-2 Inactive for designafter 28 December 194936-11 Inactive for design 36-10after 15 June 194536-1236-1636-1736-1836-2036-21Inactive for design I 36-10after 15 June 1945 IInactive,for designI36-7after 15 June 1945 IInactive for design I 36-7after 15
39、June 1945 IInactive for design 36-9after 15 June 1945Inactive for designafter 15 June 1945Inactive for design 36-9after 15 June 194540-12 Inactive for designafter 30 May 194540-13 Inactive for design 40-2after 30 May 194540-14 Inactive for designafter 30 May 194544-5 Inactive for designafter 26 May
40、1945 44-144-6 Inactive for design 44-1after 26 May 194548-5 Inactive for designafter 26 May 1945a718a71a131,Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-IMIL-STEI-1651A*TABLE III. Insert arrangements removed from MIL-STD-1651 by Revision A.InsertA
41、rrangement Status in MIL-STD-165110, 10s-5 Not to be used10, 10s-6 Cancelled after17 Oecember 195812s, 13-6 Cancelled after8 March 194514s, 15-8 Not to be used18-2 Cancelled after19 May 194518-21 Cancelled after25 November 194920-1 Cancelled after1 June 194520-28 Cancel1ed after1 June 194522-26 Not
42、to be used22-31 Not to be used22-37 Cancelled after26 June 194524-8 Cancelled after26 June 194524-13 Cancelled after26 June 194524-19 Cancelled after26 June 194532-11 Cancelled after26 June 194540-8 Not to be used6.5 International standardization agreements. Certain provisions ofthis standard are su
43、bject to international standardization agreementsASCC 12/44, NEPR 28 and NEPR 44 as listed below. When change notice, revis-ion, or cancellation of this standard is proposed that will modify the inter-national agreement concerned, the preparing activity will take appropriateI 9Provided by IHSNot for
44、 ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-sTD-1651Aa71action through international standardization channels, including DepartmentalStandardization offices, to change the agreement or make other appropriateaccommodations.INTL INTERESTa71 *ASCC 12/44#NEPR 28NEPR 4
45、46.6 Changes from previous issue. The margins of this standard aremarked with asterisks or vertical lines to indicate where changes (additions,modifications, corrections, deletions) from the previous issue were made.This was done as a convenience only and the Government assumes no liabilitywhatsoeve
46、r for any inaccuracies in these notations. Bidders and contractorsare cautioned to evaluate the requirements of this document based on theentire content irrespective of the marginal notations and the relationshipto the previous issue.6.7 Subject term (keyword) listin.Alternate insert positionsInsert
47、 positionPin contactShell sizeSocket contactCustodians:Army - CRNavy - ASAir Force - 85Review activities:Army - ARNavy - ECAir Force - 11, 15, 17, 99DLA - ESPreparing activity:Navy - AS(Project 5935-3560)10a71IProvided by IHSNot for ResaleNo reproduction or networking permitted without license from
48、IHS-,-,-I MIL-STD-1651AAPPENDIX AINSERT ARRANGEMENTS FDR MIL-C-5015, MIL-C-22992 ANO MIL-C-83723 SERIES 11ELECTRICAL CONNECTORSIIIIIIProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-1651AAPPENDIX AINSERT ARRANGEMENTS FOR MIL-C-5015, MIL-C-22992 AND MIL-C-83723 SERIES IIELECTRICAL CONNECTORS10. SCOPE10.1 g. This appendix gives the data necessary for qualification ofI insert arrangements used in MIL-C-5015. MIL-C-22992 (Classes C, J. R) andMIL-C-83723 tSeries 11) Electrical Connectors. Thisappendix 1s a mandatorypar
