NBN-EN 60095-2-1993 1875 Lead-acid starter batteries Part 2 Dimensions of batteries and dimensions and marking of terminals《铅酸起动电池组 第2部分：蓄电池尺寸和端子尺寸及标志》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

KS M ISO 25477-2009 Paper board and pulps－Basic guidelines for image analysis measurements《纸、纸板和纸浆 物象分析测量用基础指南》.pdf

KS M ISO 25518-2012 Single-use rubber gloves for general applications－Specification《通用一次性橡胶手套 要求事项》.pdf

KS M ISO 2554-2010 Plastics－Unsaturated polyester resins－Determination of hydroxyl value《塑料 不饱和聚酯树脂 羟基值的测定》.pdf

KS M ISO 2555-2002 Plastics－Resins in the liquid state or as emulsions or dispersions －Determination of apparent viscosity by the Brookfield test method《塑料 液态或象乳胶或分散体一样的树脂 布洛克菲文德粘度.pdf

KS M ISO 2556-2006 Plastics－Determination of the gas transmission rate of films and thin sheets under atmospheric pressure－Manometric method《塑料 大气压力下薄膜和薄板的气体透过率的测定 测压法》.pdf

KS M ISO 2578-2007 Plastics－Determination of time－temperature limits after prolonged exposure to heat《塑料 长期暴露于热作用后时间和温度极限值的测定》.pdf

KS M ISO 2592-2007 Determination of flash and fire points－Cleveland open cup method《闪点和燃点的测定 克利夫兰开口杯法》.pdf

KS M ISO 276-2012 Binders for paints and varnishes－Linseed stand oil－Requirements and methods of test《涂料和清漆用粘合剂 亚麻子油 要求和试验方法》.pdf

KS M ISO 277-2012 Binders for paints and varnishes－Raw tung oil－ Requirements and methods of test《涂料和清漆用粘合剂 生桐油 要求和试验方法》.pdf