NF C74-014-1994 Medical electrical equipment Part 1 general requirements for safety 3 Collateral standard general requirements for radiation protection in diagnostic X-ray equipm.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

EN 2584-2001 en Aerospace Series - Bearings Spherical Plain in Corrosion Resisting Steel with Self-Lubricating Liner - Narrow Series - Elevated Load at Ambient Temperature - Dimens.pdf

EN 2585-2001 en Aerospace series - Bearings spherical plain in corrosion resisting steel with self-lubricating liner - Wide series - Elevated load at ambient temperature - Dimensio.pdf

EN 2586-1991 en Washers Lock for Flight Control Rods - Dimensions《航空航天系列 飞行驾驶杆用锁紧垫片尺寸》.pdf

EN 2587-1990 en Rod Ends Adjustable Double Fork and Threaded Shank Dimensions and Loads《航空航天系列 两端均为叉端、杆部有螺纹的可调整的操纵杆 尺寸和负荷》.pdf

EN 2588-2006 en Aerospace series - Bearings Spherical Plain in Corrosion Resisting Steel with Assembly Slots - Dimensions and Loads《航空航天系列 带装配槽的耐蚀钢普通球面轴承 尺寸和负荷》.pdf

EN 2589-2017 en Aerospace series - Steel - Sheet and strip cold rolled - Thickness 0 1 mm less than or equal to a less than or equal to 3 mm - Dimensions《航空航天系列-钢片和带冷轧厚度0 1mm小于或等于a.pdf

EN 259-1-2001 en Wallcoverings in Roll Form - Heavy Duty Wallcoverings - Part 1 Specifications《卷式墙面饰层 重负载墙面饰层 第1部分 规范》.pdf

EN 259-2-2001 en Wallcoverings in Roll Form - Heavy Duty Wallcoverings - Part 2 Determination of Impact Resistance《卷式墙面饰层 重负载墙面饰层 第2部分 耐冲击性测定》.pdf

EN 2590-2017 en Aerospace series - Steel - Sheets and plates hot rolled - Dimensions《航空航天系列-钢片和带热轧-尺寸》.pdf