ONORM S 1393 Teil 34-1986 Rifle cartridge with brink and Chamber caliber 11 15 X 60 R《步枪子弹带边缘及药室 口径11 15 × 60 R》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

DIN 6354-1980 Milling machine arbors with steep taper complete《精加工的大锥体铣刀轴》.pdf

DIN 6355-1980 Clamping Devices Milling Machine Arbors with Taper《夹紧装置 带锥度铣床心轴》.pdf

DIN 6357-1988 Holding arbors with taper shank 7 24 for milling cutters and face milling cutters with internal alignment《内校准的铣刀和平面铣刀的7 24锥柄的铣刀杆》.pdf

DIN 6358-1988 Milling machine arbors with taper shank 7 24 for milling cutter with longitudinal or transverse drive《带纵向或横向传动装置的铣刀的 7 24 锥形刀杆的铣床刀杆主轴》.pdf

DIN 6359-1-1996 Reduction sleeves with 7 24 taper shank for parallel shanks with lateral driving surface and inclined clamping surface - Part 1 Type A with 7 24 taper shank in acco.pdf

DIN 6359-2-1996 Reduction sleeves with 7 24 taper shank for parallel shanks with lateral driving surface and inclined clamping surface - Part 2 Type B with 7 24 taper shank in acco.pdf

DIN 6360-1983 Milling machine arbors with 7 24 taper for milling cutters with longitudinal and transverse drive《带纵向和横向传动的铣刀用 7 24 锥度铣床刀柄》.pdf

DIN 6364-2000 Reduction sleeves with external taper shank 7 24 for morse taper shank with tightening thread《带紧定螺纹的莫氏锥柄用7 24外锥柄异径连接套管》.pdf

DIN 6366-2007 Clutch drive rings for shell end mill arbors《筒形端铣刀刀杆用离合器驱动环》.pdf