1、AEROSPACE STANDARD FITTING, ELBOW, 90 DEGREE, INTEGRAL WELD RING, 3000 PSI AS1584Copyright 2013 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, record
2、ing, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1980-02REAFFIRMED 2007-11 REVISED 2013-10T
3、HIRD ANGLE PROJECTION CUSTODIAN: G-3/G-3B REV.EFEDERAL SUPPLY CLASS 4730 AS1584SHEET 1 OF 3REV. EPROCUREMENT SPECIFICATION: AS1576 /6/SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entir
4、ely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised, reaffirmed, stabilized, orcancelled. SAE invites
5、 yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS1584ERATIONALE REVISE ACTIVATION DATES FOR PRI-QPL-AS1576. FIGURE 1 - FITTING, ELBOW, 90 DEGREE TABLE 1 - DIMENSIONS BASIC NO. AS1584/17/SIZE
6、CODE (NOMINALTUBE SIZE)(NOMINALTUBE WALL) A B C.010 E F 0405060810121620.250 .312 .375 .500 .625 .750 1.000 1.250 .016.020.020.026.033.039.052.065.187 .234 .297 .422 .515 .656 .875 1.093 .376- .393.438- .455.438- .455.563- .581.688- .706.876- .8941.121-1.1461.370-1.395.840.895.9821.1881.2501.4001.62
7、51.750.650 .650 .650 .650 .830 .870 1.000 1.125 .090.090.090.090.125.125.125.125AEROSPACE STANDARD AS1584SHEET 2 OF 3REV. EFITTING, ELBOW, 90 DEGREE, INTEGRAL WELD RING, 3000 PSI TABLE 1A - DIMENSIONS AND WEIGHTS BASIC NO. AS1584/17/SIZE CODE G H J U.030LBAPPROX REF CRESLBAPPROX REF TI04050608101216
8、20.212.266.329.442.553.666.8901.114.050.050.050.050.070.080.090.110.615.615.615.605.785.815.9351.050.090.090.120.120.190.190.190.190.0241 .0322 .0367 .0624 .110 .185 .326 .517 .0133 .0177 .0203 .0344 .0609 .102 .180 .285 NOTES: /1/ MATERIAL: a. CODE LETTER T - TYPE 6AL-4V TITANIUM ALLOY FORGING OR B
9、AR PER AMS4928. b. CODE LETTER V - TYPE 15-5PH CORROSION RESISTANT STEEL FORGING OR BAR PER AMS5659. 2. HEAT TREATMENT: a. MATERIAL CODE LETTER T - NONE b. MATERIAL CODE LETTER V - HEAT TREAT TO CONDITION H 1075 PER AMS2759/3. 3. FINISH: NONE. /4/ CLEANING: a. NO SUFFIX CODE LETTER IN PART NUMBER -
10、CLEAN BY ANY SUITABLE METHOD PER PROCUREMENT SPECIFICATION. b. SUFFIX CODE LETTER “C“ IN PART NUMBER - HOT ALKALINE CLEAN PER PROCUREMENT SPECIFICATION. c. SUFFIX CODE LETTER “E“ IN PART NUMBER FOR TITANIUM ALLOY PARTS ONLY - NITRIC-HYDROFLUORIC ACID ETCH PER PROCUREMENT SPECIFICATION. 5. PACKAGING:
11、 PER PROCUREMENT SPECIFICATION. /6/ PROCUREMENT SPECIFICATION: AS1576 UNLESS OTHERWISE SPECIFIED ON THIS STANDARD PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER AS LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST PRI-QPL-AS1576 FOR
12、THIS STANDARD. SEE www.eAuditN FOR CURRENT QPL ONLINE. THIS QPL REQUIREMENT SHALL BE IN EFFECT FOR PURCHASE ORDERS PLACED ON OR AFTER JULY 1, 2014. SUPPLIERS SEEKING LISTING ON THE INITIAL QPL MUST APPLY TO PRI FOR APPROVAL NO LATER THAN JANUARY 1, 2014. UNTIL THE QPL IS IN EFFECT, USERS OF THIS STA
13、NDARD ARE ADVISED TO CONTROL SOURCE APPROVALS. TRANSITION TO PRI-QPL SHALL BE COMPLETED BY JULY 1, 2014. ./7/ IDENTIFICATION AT LOCATION SHOWN: MARK PER AS478 CLASS C OR D OR METHOD 7A3, 15A3, OR 15B MANUFACTURERS IDENTIFICATION, CAGE CODE NUMBER OR TRADEMARK, BASIC PART NUMBER FOR SIZE 08 AND LARGE
14、R, LETTERS “AS“ FOR SIZE 06 AND SMALLER AND MATERIAL CODE LETTER. AEROSPACE STANDARD AS1584SHEET 3 OF 3REV. EFITTING, ELBOW, 90 DEGREE, INTEGRAL WELD RING, 3000 PSI 8. THIS PART IS DESIGNED FOR USE IN SYSTEMS WITH MAXIMUM OPERATING PRESSURE OF 3000 PSI WHEN ORBITAL ARC WELDED TO TITANIUM ALLOY OR CO
15、RROSION RESISTANT STEEL TUBING. 9. DIMENSION “J“ HAS BEEN ADDED TO THIS REVISION TO REPLACE DIMENSION “E“ TO RELATE THE TURN LENGTH TO THE TUBE STOP. THE NOMINAL DIMENSION OF “E“ HAS NOT CHANGED AND IS SHOWN AS A REFERENCE; IT MAY BE DELETED AT THE NEXT REVISION. /10/ WRENCH PADS ARE NOT REQUIRED ON
16、 THIS PART. WHEN MACHINED FROM BAR OR OVERSIZE FORGING, THE CENTER BODY SECTION SHALL CONFORM TO AS1376, TABLE 5. 11. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSU
17、E OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. 12. INTERPRETATION OF DRAWING PER ARP4296
18、 13. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 MICROINCHES Ra. 14. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. SEE AS1579. 15. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994 16. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .005, ANGULAR DIMENSIONS 1 DEGREE. /17/ EXAMPLE OF PART NUMBER:
