1、AEROSPACE STANDARD INSERT - THIN WALL, SHORT, SELF-LOCKING, 1025 F,SILVER PLATED ON INTERNAL SURFACES ONLY UNS N07718, UNJ THREAD AS3504Copyright 2012 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by
2、any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sa
3、e.org ISSUED 1993-08REAFFIRMED 1999-03 REVISED 2012-10THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.BFEDERAL SUPPLY CLASS 5340 AS3504SHEET 1 OF 2REV. BPROCUREMENT SPECIFICATION: AS3506SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengi
4、neering sciences. Theuse ofthis report is entirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised, r
5、eaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS3504BRATIONAL SILVER PLATE ON INTERNAL SURFACES ONLY ADDED, OMITTED ON REV.A, SEE NOTE 3A, NOTE
6、 1 CORRECTED, NOTE 3B CORRECT PASSIVATION NOTE ADDED, NOTE ADDED TO INDICATE AS3504-05 AND AS3504-06 ARE NOT TO BE USED FOR NEW DESIGNS. H REFACROSS FLATSJ NUMBER OF TEETH CFE REFDCLLOCKGSTRAIGHT KNURLACROSS THREADMANUFACTURERSIDENTIFICATION MAR.005 ZPER AS8879THREAD APER AS8879THREAD BZ.006 Z.005z
7、TO AS478 CLASS AFIGURE 1 TABLE 1 PARTNUMBER ATHREADBTHREADMODIFIED MINOR DIA THREADSIZE BTHREADMODIFIED MINOR DIA MINOR DIA MAXC.003D.010EREFF.005G.005 HREFJWEIGHT APPROX lb/1000 PCS AS3504-01 AS3504-02 AS3504-03 AS3504-04 AS3504-05 AS3504-06 .1900-32UNJF-3B .2500-28UNJF-3B .3125-24UNJF-3B .3750-24U
8、NJF-3B .4375-20UNJF-3B .5000-20UNJF-3B .2500-28UNJF-3A .3125-24UNJF-3A .3750-24UNJF-3A .4375-20UNJF-3A .5000-20UNJF-3A .5625-24UNJEF-3A .2170 .2785 .3405 .4010 .4630 .5290 .196 .256 .318 .382 .444 .507 .290 .380 .470 .560 .660 .750 .19 .24 .30 .35 .40 .45 .090 .090 .090 .120 .120 120.075 .075 .075 .
9、105 .105 .105 .157 .210 .266 .322 .377 .439 2024293439441.264 2.285 3.570 5.024 7.351 /11/ 9.816 /11/ AEROSPACE STANDARD AS3504SHEET 2 OF 2REV. BINSERT - THIN WALL, SHORT, SELF-LOCKING, 1025 F, SILVER PLATED ON INTERNAL SURFACES ONLY UNS N07718, UNJ THREAD NOTES: 1. MATERIAL: NICKEL ALLOY, CORROSION
10、 AND HEAT RESISTANT, AMS5662 (UNS N07718). 2. HARDNESS: 45 HRC MAX 3. FINISH: A. SILVER PLATE INSIDE DIAMETER C AND THREAD A, AND AT THE MANUFACTURERS OPTION THE END SURFACES, TO AMS2411. ON INSERTS WITH THREAD A OF .2500 OR LARGER THE COATING THICKNESS SHALL BE .0002 TO .0006. INSERTS WITH THREAD A
11、 OF .1900 SHALL SHOW COMPLETE COATING COVERAGE ON THE THREAD. B. PASSIVATE PER AS2700 PRIOR TO PLATING. DIMENSIONS MET AFTER PLATING. 4. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 125 in Ra, EXCEPT THREADS TO BE 63 in Ra AND KNUR
12、L TO BE 250 in Ra. 5. BREAK SHARP EDGES .015 MAX, UNLESS OTHERWISE SPECIFIED. 6. DIMENSIONS ARE IN INCHES. 7. PRODUCT QUALIFICATION: QUALIFICATION TESTS IN ACCORDANCE WITH AS3506 SHALL BE PERFORMED BY THE VENDOR PRIOR TO FIRST SHIPMENT OF EACH PART NUMBER. 8. PARTS TO BE INSTALLED PER AS3507 INTO MA
13、CHINED HOLES PER AS3508. 9. DO NOT USE UNASSIGNED PART NUMBERS. 10. AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. 11. AS3504-05 AND AS3504-06 ARE NOT TO BE USED FOR NEW DESIGNS.12. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVIS
14、IONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
