1、AEROSPACE STANDARD (R) PIN AND PLUG, EXPANSION, SET OF PARTS CRES, 416 OR 416SE, LONG; STD AND .010 OVERSIZE DIAMETERS, UNS S41600/UNS S41623 AS3584Copyright 2009 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any
2、 form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: htt
3、p:/www.sae.org ISSUED 1996-06REAFFIRMED 2006-05 REVISED 2009-02THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.AFEDERAL SUPPLY CLASS 5340 AS3584SHEET 1 OF 2REV. APROCUREMENT SPECIFICATION: NONESAE TechnicalStandards Board Rules provide that: “This report is published by SAE toadvance thestate of technica
4、l andengineering sciences. Theuse of thisreport is entirely voluntary, andits applicabilityandsuitability forany particularuse, including any patent infringement arising therefrom, is thesole responsibility oftheuser.”SAE reviews each technical report at least every five yearsat which time it may be
5、 reaffirmed, revised, orcancelled. SAE invites yourwritten commentsandsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS3584ARATIONALE ADD MANUFACTURERS PART NUMBERS, CLARIFY PART MARKING REQUIREMENTS AND GENERAL SAE
6、 UPDATING REQUIREMENTS FOR FORMATING.FIGURE 1 - AS3126 PIN FIGURE 2 - AS3125 PLUG TABLE 1 - PART NUMBERS AEROSPACE STANDARD PARTNUMBER /3/MANUFACTURERSPARTNUMBER /3/PIN SIZE PLUG SIZE APPROX MASSLB/100 AS3584-03 PLGA1561020A AS3126-03 AS3125-03 .116 AS3584-04 PLGA1871020A AS3126-04 AS3125-04 .179 AS
7、3584-05 PLGA2181020A AS3126-05 AS3125-05 .283 AS3584-06 PLGA2501020A AS3126-06 AS3125-06 .446 AS3584-07 PLGA2811020A AS3126-07 AS3125-07 .585 AS3584-08 PLGA3431020A AS3126-08 AS3125-08 1.082 AS3584-09 PLGA4061020A AS3126-09 AS3125-09 1.747 AS3584-10 PLGA4681020A AS3126-10 AS3125-10 2.630 AS3584-11 P
8、LGA5311020A AS3126-11 AS3125-11 3.766 AS3584-12 PLGA6561020A AS3126-12 AS3125-12 6.440 AS3584-53 PLGA1661020A AS3126-03 AS3125-53 (a) .132 AS3584-54 PLGA1971020A AS3126-04 AS3125-54 (a) .200 AS3584-55 PLGA2281020A AS3126-05 AS3125-55 (a) .315 AS3584-56 PLGA2601020A AS3126-06 AS3125-56 (a) .489 AS358
9、4-57 PLGA2911020A AS3126-07 AS3125-57 (a) .621 AS3584-58 PLGA3531020A AS3126-08 AS3125-58 (a) 1.148 AS3584-59 PLGA4161020A AS3126-09 AS3125-59 (a) 1.839 AS3584-60 PLGA4781020A AS3126-10 AS3125-60 (a) 2.751 AS3584-61 PLGA5411020A AS3126-11 AS3125-61 (a) 3.890 AS3584-62 PLGA6661020A AS3126-12 AS3125-6
10、2 (a) 6.688 (a) DESIGNATES .010 OVERSIZED PLUGS. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS3584SHEET 2 OF 2REV. A(R) PIN AND PLUG, EXPANSION, SET OF PARTS CRES, 416 OR 416S
11、E, LONG; STD AND .010 OVERSIZE DIAMETERS, UNS S41600/UNS S41623 NOTES: 1. MATERIAL: AMS5610 (416 OR 416SE CRES BAR), UNS S41600 OR UNS S41623, 20 TO 34 HRC REF. 2. FINISH: a. PLUG: SEE AS3125. b. PIN: SEE AS3126. /3/ MARK AS3584-( ) PART NUMBER AND MANUFACTURERS PART ON PACKAGE IN ACCORDANCE WITH AS
12、478, METHOD 37. IN ADDITION, PACKAGES FOR OVERSIZE PLUGS SHALL INCLUDE “OVERSIZE 416 SS” IN A RECTANGULAR BLOCK. 4. SEE AIR3276 FOR HOLE PREPARATION AND AIR 3277 FOR INSTALLATION PROCEDURE. 5. PIN AND PLUG EXPANSION SET OF PARTS SHALL CONTAIN A PIN SIZE FROM AS3126 AND A PLUG SIZE FROM AS3125 AS SPE
13、CIFIED WITH THE CORRESPONDING DASH NUMBER IN TABLE 1. 6. AS, AIR AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. 7. A CHANGE BAR ( l ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF
14、 THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. APPROVED SOURCE OF SUPPLY: THE LEE CO WESTBRO
15、OK, CT FEDERAL SUPPLY CODE FOR MANUFACTURERS NO 92555. ONLY THE ITEM DESCRIBED ON THIS DRAWING WHEN PROCURED FROM THE VENDOR LISTED HEREON IS APPROVED FOR USE IN THE APPLICATIONS SPECIFYING THIS AEROSPACE STANDARD IDENTIFICATION NUMBER. A SUBSTITUTE ITEM SHALL NOT BE USED WITHOUT PRIOR TESTING AND A
16、PPROVAL BY THE DESIGN ACTIVITY RESPONSIBLE FOR THE APPLICATION. IDENTIFICATION OF THE APPROVED SOURCE HEREON IS NOT TO BE CONSTRUED AS A GUARANTEE OF PRESENT OR CONTINUED AVAILABILITY AS A SOURCE OF SUPPLY FOR THE ITEM DESCRIBED ON THE DRAWING. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
